American Standard EDGEWATER 4932.300 User manual

- 1 -
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2016
Thank you for selecting American Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
RECOMMENDED TOOLS
1
M965717 Rev. 1.5 (2/19)
EDGEWATER™
Single Control Kitchen Faucet
With Pull Down Spray
INSTALLATION
INSTRUCTIONS
4932.300
4932.307
Certied to comply with ANSI A112.18.1M
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON CAUTION Turn off water at
main supply
SINK OR
MOUNTING
SURFACE
7
7
9
PUTTY
SPOUT BASE SPOUT BASE
2
3
4
5
8
6
74
5
8
7
6
9
3
2
A (OPTIONAL) B
1
• (A) Installation with ESCUTCHEON (1). (Escutcheon is not supplied with base product). Apply a bead of putty to bottom
edge of ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9) is properly seated in recess of faucet body. Insert
SUPPLY HOSES (2), SPRAY HOSE (7) and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting
surface. Follow mounting instructions below to secure faucet to mounting surface.
• (B) Installation less ESCUTCHEON (1). Make certain the SEAL (9) is properly seated in recess of spout base. Insert supply
HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting hole and seat spout base onto sink or mounting surface.
Do not use putty.
• Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
• Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside of sink
or mounting surface. Hand tighten LOCKNUT (6).
• Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening the screws
slightly each time until all are snug to ensure even pressure.
Plumbers' Putty or CaulkingAdjustable WrenchPhillips ScrewdriverFlat Blade Screwdriver

- 2 -
2
M965717 Rev. 1.5 (2/19)
• Turn off hot and cold water supplies before beginning.
• Connect FLEXIBLE SUPPLY HOSES (1, 2) directly to wall
supplies. Connection on tting supplies are 3/8"
compression. Connect left supply hose (Red Stripe) to Hot
wall supply. Connect right supply hose (Blue Stripe) to Cold
wall supply. Use adjustable wrench to tighten connections.
Do not over tighten.
*Faucet supplies are 21"long from faucet base.
• Note: If additional supply length is required, installer
must purchase additional parts separately.
• Important: If SUPPLY HOSES (1, 2) are too long,
loop as illustrated to avoid kinking.
MAKE WATER SUPPLY CONNECTIONS
3CONNECT SPRAY HOSE & INSTALL WEIGHTS
6
7
8
9
(Optional)
1
2
4
5
3
21"
(610 mm)
4CHECK CONNECTIONS FOR LEAKS
• Move HANDLE into “off” position.
• Turn on water supplies and check connections for leaks.
• Operate HANDLE (1) up and down, left and right to
ushwater lines thoroughly.
• Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
RED
STRIPE
BLUE
STRIPE
1
2
COLD
HOT
• Push the SPRAY HOSE END (2) into the HOSE CONNECTOR
(1) slide down LOCKING COLLAR (3) until it snaps into place
to secure connection.
• With HAND SPRAY (4) seated in SPOUT (5), install WEIGHT (7)
onto HOSE (6) 21 inches from the underside of the sink deck
and secure with SCREW (8).
• Adding SECOND WEIGHT (9) is optional.
• With one weight, spray will retract and dock potentially
requiring slight assistance.
• With two weights, spray will retract and dock automatically
once released.
• Please add the SECOND WEIGHT (9) below the initial
WEIGHT (7).

- 3 -
6
7
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
5
M965717 Rev. 1.5 (2/19)
1
3
2
REMOVE
COLD
ON
OFF HOT
SERVICE
If faucet drips, operate HANDLE several times from “off” to “on.” Do not apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, rst turn off water supply then:
• Loosen HANDLE SCREW (1) and remove HANDLE (2).
• Unthread the SNAP RING (3). Unthread three
MOUNTING SCREWS (4).
• Lift CARTRIDGE (5) off MANIFOLD (6).
• Clean MANIFOLD (6) and CARTRIDGE (5) ports.
• Place CARTRIDGE (5) onto MANIFOLD (6) and
tighten MOUNTING SCREWS (4) alternately.
• Replace SNAP RING (3), HANDLE (2),
tighten HANDLE SCREW (1).
1
2
3
4
5
6
TEST INSTALLED FAUCET
• Move HANDLE (1) into “off” position.
• Turn on water supplies.
• Check connection for leaks. (See Section 4)
• With HANDLE (1) in “off” position, unthread
SPRAY (3) from HOSE (2).
• Operate handle back to front, in COLD
and HOT positions, to ush water lines
thoroughly.
• Replace SPRAY (3) onto HOSE (2).

- 4 -
M951483-0070A
CARTRIDGE
M970037-YYY0A
HANDLE KIT
M970036 -0070A
SNAP RING
1660151-YYY
ESCUTCHEON AND
PUTTY PLATE
(OPTIONAL)
M962146-0070A
MOUNTING KIT
M964395-0070A
WEIGHT
M964395-0070A
WEIGHT
(OPTIONAL)
A911836-0070A
SEAL
M918511-0070A
CARTRIDGE SCREWS
M950362-YYY0A
SPRAY ASSEMBLY
M950415-0070A
SPRAY HOSE
M921602-0070A
BRUSH
M965717 Rev. 1.5 (2/19)
Replace the “YYY” with
appropriate finish code
CHROME 002
STAINLESS STEEL 075
MODEL NUMBER
4932.300
4932.307
EDGEWATER™
Single Control Kitchen
Faucet With Pull
Down Spray
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST
Saturday 10:00 a.m. to 4:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200