American Standard Metering 1340.725 User manual

M968492 Rev.1.5
Certified to comply with ANSI A112.18.1M
1
2
PREPARE TUBE AND TEE ASSEMBLY 3VALVE ASSEMBLY (1340.825; 1340.855; 1340.865)
2
3
1
1
2
1340.725
1340.825
1340.827
1340.855
1340.857 1340.865
9
8
Remove COUPLING NUT (1) and FERRULE (2) from each
VALVE (3) and slide onto TUBING (4).
Push TUBING (12) ends into VALVE (4) side outlets. Insert
VALVES (4) into mounting holes from underside of ledge.
Install LOCKNUTS (1), METAL WASHERS (3) and RUBBER
WASHERS (2) onto valve shanks.
Place RUBBER RING (8) into ESCUTCHEONS (7) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (10) and COUPLING NUT (11) to outlet of VALVE (4)
and tighten COUPLING NUT (11) firmly.
Place WASHER (14) on top of VALVE ASSEMBLY (4).
COLD
8"
4
10 11
6
5
11
10
12
4
4
14
MOUNTING
SURFACE
Attention; Sealing washer (5) should be
replaced everytime valve actuator (4)
is removed.
MOUNTING
SURFACE
SPREAD LAVATORY
FAUCETS
Installation
Instructions
Thank you for selecting American-Standard...the
benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Thread of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (9). If necessary, adjust LOCKNUT (1).
8
13
7
METERING 1340.725
1340.825
1340.855
1340.865
1340.827
1340.857
Plumbers' Putty or CaulkingAdjustable Wrench 2.5mm Hex WrenchChannel Locks
Recommended tools
REMOVE REPLACE
Remove HANDLE (1) by
removing INDEX BUTTON (2)
and SET SCREW (3) with a
2.5mm hex wrench.
Pull off HANDLE (1).
Remove ACTUATOR
ASSEMBLY (4).
Replace WASHER (5) with
new Washer (5) that is
provided in separate bag.
Thread VALVE ACTUATORS (13) onto VALVES (4) and torque VALVE
ACTUATOR 12-15 ft. lbs, (12-20Nm).
REMOVE HANDLE AND
ACTUATOR ASSEMBLY
1
4
5
23
HOT
Connect water supply to VALVES (4) with 1/2" IPS FLEXIBLE
SUPPLIES or 3/8" O.D. BULL-NOSE RISERS. Use adjustable wrench
to tighten connections. Do not over tighten. Be careful not to kink
copper supply when bending. Use tubing cutter to cut to proper length.
1/2" IPS FLEXIBLE
SUPPLIES or 3/8" O.D.
BULL-NOSE RISERS
COUPLING NUT
Tubing Cutter
7
2
4
5/16''
MIN. MOUNTING
SURFACE
8
9
1
3

M968492 Rev.1.5
3a VALVE ASSEMBLY (1340.725)
For Cold or Tempered Water Supply
5
4
12
13
6
7
2
4
5/16'' MIN. MOUNTING
SURFACE
8
9
1
3
9
MOUNTING
SURFACE 8
COLD OR
TEMPERED
WATER
11
10
7
1/2" IPS FLEXIBLE SUPPLIES or
3/8" O.D. BULL-NOSE RISER
COUPLING NUT
Valve assembly is same as two handle lavatory faucets. See Step 3
instructions for assembly, (1340.725 Single Valve Faucet) is for Cold
or Tempered water only.
14
Turn off hot and cold water
supplies before beginning.
CAUTION
4
Assemble RUBBER WASHER (5) and BRASS WASHER (6) and
LOCKNUT (7) onto SPOUT SHANK (4). Align SPOUT ASSEMBLY.
From underside of ledge, tighten LOCKNUT (7) approximately
halfway up the spout shank.
Press SPOUT SHANK (4) onto TEE (8) making certain that the
O-RING (3) is properly seated on SHANK (4). Push COUPLING (9)
into TEE (8) and attach to SPOUT SHANK (4) and tighten.
Por la parte inferior, apriete la tuerca (7) para asequrar el
cuerpo a la superficie de montaje.
SPOUT ASSEMBLY
Install RING WASHER (1) into SPOUT (2) recess. Check
that O-RING (3) on end of SPOUT SHANK (4) is in place. Insert
SPOUT SHANK (4) into center hole on mounting surface.
SPOUT
RECESS 1
3
2
8
MOUNTING
SURFACE
SPOUT
ASSEMBLY
4
COLD
HOT
9
5
6
7

M968492 Rev.1.5
Remove HANDLE (1) by removing INDEX BUTTON (2)
and SET SCREW (3) with a 2.5mm hex wrench.
Pull off HANDLE (1).
To increase cycle time, turn the gray PLASTIC ADJUSTING
KNOB (4) clockwise.
To decrease cycle time, turn the gray PLASTIC
ADJUSTING KNOB (4) counter-clockwise.
Replace SET SCREW (3), INDEX BUTTON (2) and
HANDLE (1). Test faucet for proper operation and
cycle time.
TO ADJUST CYCLE TIME
7SERVICE
8
1
23
4
TO INCREASE
CYCLE TIME
ROTATE
CLOCKWISE
TO DECREASE
CYCLE TIME
ROTATE
COUNTER-
CLOCKWISE
2.5mm HEX WRENCH
CARE INSTRUCTIONS:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR
WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH
WITH A COARSE SURFACE.
Remove HANDLE (1). Refer to Step 3 for handle removal.
Remove ACTUATOR ASSEMBLY (1).
Remove WASHER (3). Pull out VALVE ASSEMBLY (4) and
FILTER SCREEN (5).
Inspect that VALVE ASSEMBLY (4), FILTER SCREEN (5) and
VALVE SEAT (6) are clean and free from debris. VALVE
ASSEMBLY (3) and FILTER SCREEN (5) can be cleaned with
soap and water.
Replace FILTER SCREEN (5), VALVE ASSEMBLY (4) and WASHER (3).
Place WASHER (3) on top of VALVE ASSEMBLY (4). Thread VALVE
ACTUATOR (2) onto faucet. Torque VALVE ACTUATOR (2)
to 12-15 ft. lbs (15-20 Nm).
Replace HANDLE (1).
1
4
3
5
2
REMOVE REPLACE
6
1
2
Turn on water supplies and check connections for leaks.
Remove AERATOR (1) with KEY (2) supplied.
Operate HOT and COLD HANDLES by pressing down on HANDLES.
Both Hot and Cold handles are set for approximately 8 second operating cycles.
Replace AERATOR (1).
TEST INSTALLED FITTING
6
PRESS HANDLE
DOWN TO OPERATE
5INSTALL HANDLES
Remove INDEX BUTTON (1; 2) and loosen SET
SCREW (3) with a 2.5mm hex wrench.
Install HANDLES (4) onto VALVE STEM (5).
Tighten SET SCREWS (3) with 2.5mm Hex Wrench.
Replace INDEX BUTTONS. Red (1) in Left HANDLE (4)
Blue (2) in Right HANDLE (4).
14
3
2.5mm
HEX WRENCH
3
5
4
2
Attention; Sealing washer (3) should be
replaced everytime VALVE ACTUATOR (2)
is removed.