American Standard Elevate AM00840400 User manual

THE BEST BATH OR SHOWER EXPERIENCE?
THE ONE NOBODY INTERRUPTS.
Thank you for buying an American Standard
bath or shower product.
We’re so grateful you did, and you will be too. Not just while you’re waking
up each morning, but also every time a dirty gardener, sweaty soccer player,
or muddy dog gets cleaned up. How do we know? Just like you, we’ve lived
with that same beautiful chaos called life for almost 150 years. We believe
that while every home should appreciate in value, we never forget the
sentimental value that grows from enjoying life in the heart of home—
your kitchen and bath. That’s why we love your stories and ideas; they help
us innovate with products that make your life easier.
Or, visit americanstandard-us.com/bathroom/tub-and-shower-
doors to watch video, view/download installation manuals
or learn more about your product.
Have a question or need help on install?
For questions or help on installation call us at 800-442-1902.
For a copy of our warranty in additional languages,
please visit Americanstandard.com

OWNERS MANUAL
Elevate®Curved Corner Shower Door
AM00840400
INSTALLATION INSTRUCTIONS
Thank you for selecting American Standard – the benchmark of fine quality for over 150 years. To ensure this
product is installed properly, please read these instructions carefully before you begin. Certain installations may
require professional help. Also be sure your installation conforms to local codes.
INSTALLATION PREPARATION
• Please unpack carefully and identify all parts needed for installation by using the Box Contents page as a
reference. Inspect the product and report any damages or missing parts immediately to customer care by
calling 800-442-1902. Follow the prompts for consumer/shower doors.
• These Elevate shower doors were developed to be installed with the Elevate shower base and Elevate
shower walls. If you are using a different base and wall set, you may need additional hardware and tools to
complete the installation.
• Handle the glass panels carefully and protect the edges. Unequal pressure applied during installation can
cause cracking or breakage, and the sharp corners on the glass panels can cause damage to the wall or
floor materials.
• Ensure adequate wall support is provided to area where shower door is to be installed.
• Shower base and wall material must be installed prior to the door installation.
• Wear protective equipment during installation to avoid injury.
• Please keep these instructions for after care and customer service details.
!WARNING: PRODUCT IS HEAVY AND REQUIRES TWO PEOPLE FOR INSTALLATION.
!WARNING: TEMPERED GLASS CANNOT BE DRILLED, CUT OR MODIFIED.

BEFORE YOU BEGIN
Inspect your product thoroughly before installing. Take extra care in handling surfaces
of the bath and use only non-abrasive cloths to avoid scratching. Observe all local plumbing
and building codes.
INSIDE THE BOX
RECOMMENDED TOOLS AND MATERIALS
Level
36"x 72"Curved Shower Door
Hammer
Installation steps will indicate which tools should be used with asscociated letter
Pencil
Tape
Measure
Caulking Gun Drill
1/4"(6 mm))
Drill Bits #2 Square Drive Bit
1/8"(3.2 mm)
Drill Bits #2 Square Drive Bit
Phillips
Screwdriver
Regular
Screwdriver
Safety
Equipment
B
H
I J
ACD
FG
E
K
Drill 1/4" (6mm) & 1/8" (3.2mm)
Drill Bits #2 Square Drive Bit
Drill 1/4" (6mm) & 1/8" (3.2mm)
Drill Bits #2 Square Drive Bit
Image shown may vary from product purchased.

BOX CONTENTS
1x Installation Instruction
[1] 1x Top Rail
[2] 1x Bottom Threshold
[3] 2x Wall Posts
[4] 2x Inserted Gaskets
[5] 1x Side Gasket (Longer)
[6] 1x Side Gasket (Shorter)
[7] 1x Magnetic Seal (Longer)
[8] 1x Magnetic Seal (Shorter)
[9] 1x Fixed Panel A.
[10] 1x Door Panel-L
[11] 1x Fixed Panel B
[12] 1x Handle Set
[13] 2x Exterior Wheels
[14] 4x Fasteners
[15] 2x Interior Adjust Wheels
[16] 1x Wrench
[17] 1x 2 mm Allen Key
[18] 1x 2.5 mm Allen Key
[19] 1x Bottom Guide A
[20] 1x Bottom Guide B
[21] 1x End Cap
[22] 1x Screw Cap
[23] 2x Screw St4x25
[24] 6x Wall Anchors
[25] 6x Screws ST4x35
[26] 6x Screw Caps
[27] 6x Back Screw Caps
[28] 1x Installation aid
[29] 1x Glass Stabilizer

ASSEMBLY DRAWING
[1] 1x Top Rail
[2] 1x Bottom Threshold
[3] 2x Wall Posts
[4] 2x Inserted Gaskets
[5] 1x Side Gasket (Longer)
[6] 1x Side Gasket (Shorter)
[7] 1x Magnetic Seal Longer)
[8] 1x Magnetic Seal (Shorter)
[9] 1x Fixed Panel A
[10] 1x Door Panel-L
[11] 1x Fixed Panel B
[12] 1x Handle Set
[13] 2x Exterior Wheels
[14] 4x Fasteners
[15] 2x Interior Adjust Wheels
[16] 1x Wrench
[17] 1x 2 mm Allen Key
[18] 1x 2.5 mm Allen Key
[19] 1x Bottom Guide A-L
[20] 1x Bottom Guide B
[21] 1x End Cap
[22] 1x Screw Cap
[23] 2x Screw ST4x25
[24] 6x Wall Anchors
[25] 6x Screws ST4x35
[26] 6x Screw Caps
[27] 6x Back Screw Caps
[28] 1x Installation aid
[29] 1x Glass Stabilizer
[14]
[13]
[15]
[10]
[11]
[21]
[24]
[25]
[5]
[6]
[2]
[3]
[12]
[20]
[19]
[23]
[16]
[26]
[27]
[17]
[18]
[28]
[22]
[29]
[8]
[4]
[7]
[1]
[9]

INSTALLATION INSTRUCTIONS
1
• In this step, you’ll need following parts: [3] x2, [24] x6, [25] x6, [26] x6, [27] x6
• In this step, you’ll need the following tools: B, C, D, G, I, J
1a. From outside edge of shower base threshold, measure 1-3/16"(30.2mm) and mark deck of base with
Pencil [I]. Place Wall Post [3] onto mark on deck of base and plumb. Tape Wall Post [3] to wall to
temporarily hold wall post in place.
1b. Mark each predrilled hole in Wall Post [3] with a pencil and remove Wall Post [3]. Repeat on opposite side.
1c. If using supplied Wall Anchors [24] drill each of the marks on the wall from step 1b using a 6mm drill bit.
If not using Wall Anchors, drill using appropriate size bit for screw being used.
1d. If using Wall Anchors [24], place into each drilled hole.
1e. Place either Left or Right Wall Post [3] on the wall, and place a Back Screw Cap [27] over each ST4x35
screw [25] and screw Wall Post [3] into place.
1f. Cover each ST4x35 screw head [25] using Screw Caps [26].
PREPARING INSTALLATION OF WALL POSTS
IMPORTANT GENERAL INFORMATION
This unit is best installed by two people.
Cover drain with tape prior to installation to prevent the loss of small parts.
Unpack your unit carefully and inspect for freight damage. Lay out and identify all parts using Box
Contents and Assembly Drawing as a reference. Before discarding the carton check to see that no
small hardware parts have fallen to the bottom of the box. If any parts are damaged or missing refer to
the description noted in the instructions when inquiring about replacements.
Handle the glass panels carefully and protect the edges. Although tempered glass is very resistant to
breakage, the glass can still break if unequal pressure is applied during installation and the sharp corners
of the panel can damage tile and flooring surface.
Be sure to wear safety glasses whenever drilling or cutting. When drilling holes in ceramic tile or marble
use a center punch and hammer to carefully break the glazed surface. This will prevent skidding
when drilling.
NOTE: TEMPERED GLASS CANNOT BE DRILLED, CUT OR MODIFIED.
[3]
[3]
[3]
I
J
D
Screw
ST4x35
6mm
Shower
Base Outside of
Threshold
Locate Wall Post From Outside of Threshold
[24]
[27]
[26]
[25]
1b
1c
1e
1f
1a 1d
[3]
H
G
B
I
1a

2INSTALLING FIXED PANELS
2a. Insert Fixed Panel A [9] into Wall Post [3].
2b. Ensure Fixed Paned A [9] fits fully into the Wall Post [3] as illustrated. Then install Fixed Panel B [11]
on the right (opposite) side in the same manner.
2c. Place Top Rail [1] from inside of shower area and align holes in Top Rail [1] with holes in Fixed Panel A [9]
on left side. Attach Top Rail [1] to Fixed Panel A [9] using 2 Fasteners [14] and screw into the Top Rail [1].
2d. Tighten the 2 Fasteners [14] turning clockwise using supplied 2mm Allen Key [17] placed into a hole in
Fastener. Ensure the clear plastic spacer of the Fastener [14] stays in the hole of the Fixed Panel. Do not
overtighten Fasteners [14] or damage to the glass Fixed Panels may occur. Repeat on the opposite side
for Fixed Panel B [11].
2e. Place Inserted Gaskets [4] from outside of shower area, between Wall Post [3] and Fixed Panel A [9]
using supplied Installation Aid [28] while checking level on top of panel.
2f. Fully press Inserted Gasket [4] into Wall Post [3] between Fixed Panel A [9] and Wall Post [3] as illustrated.
Repeat on opposite side. NOTE: Closely check the gasket and ensure it is fully inserted as the gasket aids
in securing the glass panel to the wall post and provides a water tight seal.
• In this step, you’ll need following parts: [1] x1, [4] x2, [9] x1, [11] x1, [14] x4, [17] x1, [28] x1
• In this step, you’ll need the following tool: B
NOTE: TWO PEOPLE REQUIRED
[3]
[14]
[14]
[17]
2c
=
=
2e 2f
2c 2d
2a 2b
[9]
[9]
[3]
[9]
[9]
[4]
[1]
[1]
[1]
[3]
[9]
[4]
[28]
[11]
2a
2e
2e
2a
2c
[9]
NOTE: Fixed Panel A [9] MUST be installed on left side only. See above illustration for reference.

3INSTALLING BOTTOM GUIDE/CAP & BOTTOM THRESHOLD
• In this step, you’ll need following part: [2] x1, [19] x1, [21] x1,
• In this step, you’ll need the following tools: A, B, C, G, I
3.2mm
[2]
[2]
[2][2]
[21]
[11]
[11]
[19]
[9]
[19]
[2]
[19]
[9]
3b3a
3d3c
3f3e
3h
3g
3j
3k
3i
[9]
[21]
[2]
[19]
[9]
[2]
[11]
[21]
[21]
[2]
[11]
[2]
[2]
I
J
F
Shower
Base A
Screw
ST4x25
[23]
Screw
ST4x25
[23]
GG
[21]
[11]
[22]
B
3a. Place slot in Bottom Guide A-L [19] over Bottom
Threshold [2] and Fixed Panel A [9].
3b. Place End Cap [21] over Bottom Threshold [2]
and Fixed Panel B [11]. NOTE: Evenly space Bottom
Threshold [2] between Bottom Guide A-L [19] and
End Cap [21] so no spaces exist between the two.
3c. Check that both Fixed Panel A [9] and Fixed
Panel B [11] are plumb using a Level. Mark the
surface of the shower base deck using a pencil at
the center slot of Bottom Guide A-L [19] .
3d. Mark the surface of the shower base deck using
a Pencil at the center hole of End Cap [21].
3e. Remove both Bottom Guide A-L [19] and End Cap [21] and drill
at both marked locations using a 3.2 mm (1/8") Drill Bit.
3f. Apply a silicon sealant to the underside of the Bottom Threshold [2]
3g. Place Bottom Threshold [2] on deck of Shower Base, then place Bottom
Guide A-L [19] over Bottom Threshold [2] and Fixed Panel A [9].
3h. Place End Cap [21] over Bottom Threshold [2] and Fixed Panel B [11].
3i. Screw Bottom Guide A-L [19] into place using supplied ST4x25 Screw [23].
3j. Screw End Cap [23] into place using supplied ST4x25 Screw [23].
3k. Snap Screw Cap [22] over screw hole of End Cap [23].

4INSTALLING EXTERNAL/INTERNAL WHEELS & DOOR PANEL-L
4a. Unscrew and separate 2 Exterior Wheels [13] and 2 Interior Adjust Wheels [15]
as illustrated. Install one Exterior Wheel [13] into upper hole of Door Panel-L [10]
as illustrated and fully tighten. Install one Interior Adjust Wheel [15] in the lower hole
of Door Panel-L [10] as illustrated and lightly tighten. Install the second set of
Exterior Wheel [13] and Interior Adjust Wheel [15] on the opposite side of Door
Panel-L [10] and tighten.
4b. Lift assembled Door Panel-L [10] into shower area and place both Exterior Wheels [13]
onto Top Rail [1] while inserting the Interior Adjust Wheels [15] into a notch in the
Top Rail [1] which accepts the Interior Adjust Wheels [15] and slide Door Panel-L
into place.
4c. Adjust both left and right Interior Adjust Wheels [15] using supplied 2mm Allen
Key [17] to secure Door Panel-L [10] in place onto Top Rail [1].
4d. Unscrew Glass Stabilizer [29] turning counterclockwise and separate the
Glass Stabilizer [29] as illustrated using supplied 2mm Allen Key [17].
4e. Insert one section of Glass Stabilizer [29] into outside hole of Door Panel-L [10]
as illustrated while inserting opposite section of the Glass Stabilizer [29] from
inside of Door Panel-L [10]. Screw clockwise to secure Glass Stabilizer [29]
to Door Panel-L [10] while aligning the groove side of the Glass Stabilizer [29]
to rest over the Bottom Threshold [02].
4f. The Glass Stabilizer [29] should be lowered over the Bottom Threshold [2] as illustrated. Ensure the
Glass Stabilizer [29] stays in place on the Bottom Threshold [29] as the door is opened and closed.
4g. Slide slot of Bottom Guide B [20] onto Door Panel-L [10] as illustrated.
4h. Snap Bottom Guide B [20] into Bottom Guide A-L [19] as illustrated.
[10]
[10]
[10]
[13]
[15]
[20]
[29]
[17]
[13]
[1]
[10]
[10]
[9]
View from inside
View from inside
4a
4g
4e
4d
4a
4e4b
4c 4f
4g
4h
View from
inside
[17]
[17]
[20]
[2]
[19]
[13]
[10]
[1]
[13]
[29]
[2]
• In this step, you’ll need following parts: [10] x1,
[13] x2, [15] x2, [17] x1, [20] x1, [29] x1

5INSTALLING SIDE GASKET/MAGNETIC SEAL AND HANDLE SET
5a. Install Longer Side Gasket [5] onto left edge of Door Panel-L [10]. Install Shorter Side Gasket [6]
onto right edge of Fixed Panel A [9].
5b. Install Longer Magnetic Seal [7] onto right edge of Door Panel-L [10]. Install Shorter Magnetic Seal [8]
onto left edge of Fixed Panel B [11].
5c. Unscrew upper portion of Handle Set [12 Longer End] and install into upper hole of Door Panel-L [10].
5d. Unscrew lower portion of Handle Set [12 Shorter End] and install into lower hole of Door Panel-L [10].
5e. Tighten both upper and lower portions of Handle Set [12] using supplied 2.5 mm Allen Key [18] to secure
Handle Set [12] to Door Panel-L [10].
• In this step, you’ll need following parts: [5] x1, [6] x1,
[7] x1, [8] x1, [12] x1, [18] x1
[11]
[10][10]
[10]
[18]
[5]
[9]
[6][12]
[10]
[10]
[1]
[1]
[8][7]
[12]
5a
5a 5b
5c
5c
5b 5d
5e