American Standard Comrade Maintenance manual

Adjustable Wrench
Channel Lock Pliers Regular Screwdriver
Recommended Tools & Materials
Phillips Screwdriver
Pipe Wrench
Putty Knife
Drill Saber Saw
Basin Wrench
Plumbers' Putty or Caulking
Tubing Cutter
Tape
Measure
Hacksaw
NOTE: For installation of models using concealed or exposed arms, follow instruction provided by arms manufacturer.
Level
SAVE FOR FUTURE USE
730427-100 Rev. E
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
Product names listed herein are
trademarks of AS America, Inc.
© AS America, Inc. 2015
NOTE: Pictures may not exactly define contour of china and components.
WALL HUNG SINK
INSTALLATION INSTRUCTIONS
CARE AND MAINTENANCE
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years.To ensure this product is installed
properly, please read these instructions carefully before you begin. (Certain installations may require professional help.) Also be
sure your installation conforms to local codes.
!
OBSERVE LOCAL PLUMBING AND BUILDING CODES
3
12
4
Provide suitable reinforcement behind
finished wall for lavatory hanger mounting
screws. *Determine horizontal center line
location of support from the table listed in
Step 2. (Make sure support bottom
extends to lavatory back wall bottom.)
NOTE: If replacing an existing sink be
certain to shut off water supply before
removing old sink.
Hanger
Location
C/L of 2x8
Support
Finished
Floor
*
Determine the
desired rim height
(for example 32")
then select from the
Table at right the
height of the hanger
mounting bolts
centerline
EXAMPLE:
For Lucerne:
32"-1"= 31"
For Missouri:
32"+1"= 33"
Drill pilot holes in positioning screw
slots of hanger. (Note: Some models
are supplied with anchor screws, or
steel hangers for lavatory installations.
Other models are not provided with
mounting hardware which can be
purchased at local hardware outlets.
Lavatories with bottom anchor screw
holes should be secured with anchor
screws in addition to hangers.
Part # Model
TABLE
Distance "A"
0124
0321
0355/0356
0372/0373
4867/4869
0436
9024
Comrade
Declyn
Lucerne
Penlyn
Regalyn
Missouri
Decorum
- 2-1/2" (64mm)
- 2-3/4" (70mm)
- 1" (25mm)
- 1/8" (3mm)
+ 2-3/4" (70mm)
+ 1" (25mm)
- 3-11/16" (93mm)
HOLES FOR
ANCHOR SCREWS
IN BACK DRAPERY
RIM
HEIGHT
*
SUPPLIES
AS REQUIRED
WASTE
FINISHED FLOOR
HANGER
C/L OF HANGER ANCHORING SLOTS
MOUNTING
SCREW
HOLES (4)
POSITIONING
SCREW
SLOTS (2)
A
Position hanger according to Step 2,
making sure its center is aligned
with the waste hole centerline. 
Mark the hanger screw locations
through its mounting holes.

AS AMERICA, INC. ONE YEAR LIMITED WARRANTY
If inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is
defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a same or similar model.
This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof
of purchase will be required—save sales receipts.
This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this
product should check with a local building or plumbing contractor to insure local code compliance before installation.
This limited warranty will be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it
has been modified in a manner inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal
or installation including any costs of any surrounding material such as tile or marble. American Standard is not responsible for any other
incidental or consequential damages attributed to a product defect or to the repair or exchange of a defective product, all of which are
expressly excluded from the warranty. This limited warranty does not cover the extension beyond the duration of this limited warranty of any
implied limited warranties, including those of merchantability or fitness for an intended purpose. (Some states or provinces do not allow the
exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to
province, in which case this limited warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product
was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:
2730427-100 Rev. E
In the United States:
American Standard Brands,
P.O. Box 6820
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
For residents of the United States, warranty
information may also be obtained by calling
the following toll free number: [phone]
www.americanstandard.com
In Mexico:
Customer Service Manager
AS Maquila, S.A. de C.V.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
www.americanstandard.com.mx
THIS WARRANTY IS NOT TRANSFERABLE FROM ORIGINAL CONSUMER PURCHASER.
56
78
Steel Hanger
Mounting Screw
Positioning Screw
Anchor Screw
(if used)
Lavatory
Affix hanger to wall (hand tighten only). Mount
lavatory for positioning, level the deck, and mark
bottom anchor screw holes (if applicable). Remove
lavatory, tighten the hanger positioning screws and
drill pilot holes for anchor screws and 4 mounting
screws. Install and tighten the mounting screws.
Return the fitted lavatory to
the installed position. Connect
trap to drain assembly hand
tight to check alignment. It
may be necessary to cut off
part of the tailpiece (area "B")
or part of the horizontal leg of
the trap (area "C").
Secure lavatory on
hanger as shown in 5.
Insert and tighten anchor
screws if applicable.
Connect hot and cold
supply lines to the
shut-off valves. Tighten
trap joints for watertight
assembly. Apply a bead
of caulk around the edge
which contacts the wall
as shown.
Following manufacturers instructions, install faucet
and drain assembly. (Not included). Be certain to
apply a bead of sealing putty on the underside of
the drain (Part "A") in order to ensure a watertight
seal between the lavatory and drain. Remove
excess putty after installing drain on lavatory.
B
C
A
Shut-off
Valves
Caulk
In Canada:
AS Canada ULC
5900 Avebury Road
Mississauga, Ontario
Canada L5R 3M3
Toll Free: [phone]
www.americanstandard.ca