American Standard 8350.235 User manual

Exposed Yoke Wall Mount
Utility Faucet
ROUGHING-IN DIMENSIONS
M965041 Rev 1.3
Certified to comply with ANSI A112.18.1M
8350.235
8350.243
ROUGH-IN
1
Prepare water supply lines per "Roughing-in
Dimensions". Install 1/2" NPT. SUPPLY NIPPLES
Installation
Instructions
Plumbers' Putty or Caulking
Adjustable Wrench Phillips Screwdriver
Channel Locks
RECOMMENDED TOOLS
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
8350.235
8350.235
8350.243
8350.243
1/2 NPT. FEMALE THREADS
FINISHED WALL
1/2 NPT. SUPPLY NIPPLE
1/2 to 1
1-1/4 DIA. OPENING
2-1/2"
(100mm)
8"
(203mm)
3/4" HOSE
TREADS 6-6/8"
(173mm)
OFFSET
SHANKS
HOT COLD
BACKFLOW
PREVENTER
8"
(203mm)
3/4" HOSE
TREADS 6-1/2"
(164mm)
12-1/2"
(317mm)
OFFSET
SHANKS
BACKFLOW
PREVENTER
1/2 N.P.T.
FEMALE
2-1/2"
(63mm)
HOT COLD
12-1/2"
(317mm)
2-3/8" DIA.
(60mm)
1/2 N.P.T.
FEMALE
2-3/8" DIA.
(60mm)

M965041 Rev 1.3
SERVICE
4
To change direction of handle rotation, proceed as follows:
Turn HANDLE to OFF position.
Remove HANDLE SCREW and HANDLE.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90°and replace.
Replace SPRING CLIP (1).
Replace HANDLE and HANDLE SCREW.
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90°.
90°
3
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Turn HANDLES (1) TO OFF POSITION.
Slowly turn water supplies on and
check all connections for leaks.
Operate HANDLES (1) to flush water
lines thoroughly.
Turn HANDLES (1) to OFF position.
Thread ESCUTCHEONS (2) against
finished wall.
TEST FAUCET
2
5
3
4
6
2
2
1
1
FINISH INSTALLATION
90˚
8"
OFF
ON
Slide COUPLING NUTS (5) onto INLET SHANKS (3).
Thread ESCUTCHEONS (2) fully onto INLET SHANKS (3).
Thread INLET SHANKS (3) onto SUPPLY NIPPLES (1). Distance
between INLET SHANK (3) outlets must be 8" to match the VALVE.
Insert RUBBER WASHERS (4) into INLET SHANK (3).
Attach VALVE (6) to INLET SHANKS (3). Tighten both
COUPLING NUTS (5) firmly.

Exposed Yoke Wall Mount
Utility Faucet
M965041 Rev 1.3
MODEL NUMBER
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2010
HOT LINE FOR HELP
A904939-0020A
BONNET NUT
M962962-YYYOA
FEMALE ECCENTRIC
SHANK W/ECUTCHEON
M911631-0070A
GASKET
951764-0070A
CARTRIDGE
CHROME
ROUGH CHROME
002
004
Replace the "YYY" with
appropriate finish code
051322-0020A
HANDLE SCREW
051211-0070A
INDEX KIT (PAIR)
051210-0020A
LEVER HANDLE
8350.235
8350.243
8350.235
8350.243
M962952-0020A
VACUUM BREAKER
REPAIR KIT
M918014-0070A
ADAPTER