American Standard Fluent 7186.900 User manual

*Wrench
Certified to comply with ANSI A112.18.1
Recommended Tools
*Supplied with Fitting
*Hex key
SPOUT RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
12
Assemble RUBBER WASHER (4) and BRASS WASHER (5) and
LOCKNUT (6) onto SPOUT SHANK (3). Align SPOUT ASSEMBLY
and from underside of ledge secure SPOUT ASSEMBLY into
position with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
4
2
31
3
4
1
2
4
5
Prepare TUBE and TEE ASSEMBLY (1) to fit each VALVE (2).
Distance between valves should be between 10-1/2" and 12"
(center to center). If necessary, cut and/or bend TUBING
carefully. Make sure tube bend is close to the TEE (1) so
that it will not effect the compression joint at the
VALVE CONNECTION.
ADJ. 10-1/2 TO 12
6
5
Flat Blade Screwdriver
Adjustable Wrench
Slip Jaw Pliers
MOUNTING
SURFACE
VALVE inlets are 3/4-inch NPT male.
NOTE
ROUGHING-IN DIMENSIONS
MOUNTING
SURFACE
DECK-MOUNT BATH FILLER
Installation
Instructions
7186.900
7186.901
Install RING WASHER (1) into SPOUT recess. Check that O-RING (2)
on end of SPOUT SHANK (3) is in place. Insert SPOUT SHANK (3)
through center hole on mounting surface.
FLUENT™
3
M965623
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
MOUNTING
SURFACE
165mm to 305mm
(ADJ. 6-1/2 TO 12)
38mm
(1-1/2" MAX.)
32mm
(1-1/4 " MAX.)
31mm
(1-3/16 " DIA.)
76mm
(3
")
40mm
(1-5/8 ")
DIA.
(H)(C)
29mm
(1-1/8
" DIA.)
208mm
(8-3/16
")
305mm
(12 " MAX)
53mm
(2-1/16
")
27mm
(1-1/16 " DIA.)
3/4-14 MALE
N.P.T. INLETS
93mm
(3-5/8")
140mm
(5-3/8")
219mm
(8-5/8")
250mm
(9-3/4")
199mm
(7-7/8")
SPOUT
ASSEMBLY
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.

9
2
4
5/16'' MIN. MOUNTING
SURFACE
HOLE IN BACK
OF HANDLE
HOLE IN BACK
OF ADAPTER
FOR FITTING
LESS SPRAY
10
11
11
10
1
3
4
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8 or 8a) into TEE (5) and
attach to SPOUT SHANK (6) and tighten. For 7186.901 use a 10 mm
(3/8") hex key.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to left VALVE inlet and COLD water supply to right valve
inlet using appropriate connectors. Note: VALVE inlets are 3/4-inch NPT male.
VALVE ASSEMBLY
HOT
COLD
12 13
7
6
8
8a
5
13
12
3
4
MOUNTING
SURFACE
Thread of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).
10
9
9
M965623
INSTALL HANDLES
Turn hot and cold VALVE STEMS (1) to the off position.
Push ADAPTER (2) onto VALVE STEM (1), so the hole in ADAPTER (2) is
facing toward the back wall. VIEW “A”. Install and tighten STEM SCREW (3)
to secure ADAPTER (2).
Align the hole in back of the HANDLE (4) with the hole in ADAPTER (2).
Install the HANDLE (4) onto ADAPTER (2).
Tighten SET SCREW (5) with 5/64"HEX WRENCH (6) supplied. 2
1
4
5
6
3
5/64" HEX
WRENCH
5SERVICE
To change direction of handle:
If spout drips, operate handles several times from
OFF to ON position. Do not force - handles turn only 90˚.
Turn valve to OFF position.
Remove SET SCREW (1) with 5/64" Hex Wrench.
Pull HANDLE (2) “UP” firmly to release from
ADAPTER (3).
Remove ADAPTER SCREW (4) and pull off ADAPTER (3).
Remove SPRING CLIP (5). Lift STOP WASHER (6),
turn 90˚ and replace. Replace SPRING CLIP (5).
Re-install HANDLE ASSEMBLY.
VIEW “A”
VIEW “A”
90˚
5
6
HOLE IN BACK
OF HANDLE
3
2
1
4

9
HANDSHOWER INSTALLATION
(FOR MODEL 7186.901 ONLY)
TEST INSTALLED FAUCET
7
Turn VALVES (1) to "off" position.
Lift HANDSHOWER (3) from holder, direct spray into tub, lift
TRANSFER KNOB (4) to check HANDSHOWER (3) and HOSES for leaks.
Turn VALVES "off."
Be sure RUBBER RING (2) is properly seated in ESCUTCHEON (1). Drop SPRAY ESCUTCHEON (1)
through the fourth hole of the tub ledge (12" max from SPOUT center) with SPRAY ESCUTCHEON (1)
directed towards tub center. Install RUBBER WASHER (3) and LOCKNUT (4) from
underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (4).
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of TEE (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and ESCUTCHEON (1). Note: SPRAY HOLDER (6)
must be separate from ESCUTCHEON (1) to get HOSE (8)
through ESCUTCHEON (1). Install SEAL (9) and connect to
HOSE (10). INSTALL second SEAL (9) and connect
HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
6
With handles in "off" position, turn on water supplies and check
all connections for leaks.
Operate both handles and flush water lines thoroughly.
Check SPOUT (2) mounting for leaks.
The flow rate of this Tub Filler exceeds 20 gallons/minute
at higher water pressure. Do not fill bathtub unattended.
CAUTION
1
2
3
4
5
7
8
10
9
9
11
6
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 2014
1
1
3
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90˚.
2
M965623
IN MEXICO 01-800-839-12-00
4
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles.
8
Hex wench, supplied
To remove handles, reverse steps in STEP 4.
To remove SPOUT (1), proceed as follows:
Lift KNOB (2) and unscrew from TRANSFER ROD (7).
Remove SET SCREW (3) using 5 mm hex wrench supplied.
Lift SPOUT (1) off SHANK (4) carefully and remove RUBBER
RING (5).
Unscrew SHANK SLEEVE (6) and lift TRANSFER ROD (7) from
SHANK (4).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (5) is properly seated in its recess at the base of SPOUT (1).
Make certain SET SCREW (3) is properly aligned and tight so that
SPOUT (1) is locked in place.
3
7
5
4
6
1
2
DO: CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON
FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH CLEANERS, OR A CLOTH WITH A
COARSE SURFACE.
CARE INSTRUCTIONS:

028679-0070A
TUBE & TEE
ASSEMBLY
012668-0070A
SHANK KIT
030274-0070A
SHANK
MOUNTING KIT
911903-0070A
RUBBER RING
M961634-0070A
VALVE
MOUNTING KIT
012078-0070A
VALVE COUPLING KIT
028664-YYY0A
HAND SHOWER
HOLDER
M950092-YYY0A
HAND SHOWER
028699-0070A
COUPLING (FOR TRANSFER)
A922388-YYY0A
STREAM STRAIGHTENER
028667-YYY0A
HAND SHOWER HOSE
033760-0070A
HAND SHOWER SEAL KIT
051343-0070A
HOSE KIT
030275-0070A
SHANK SLEEVE KIT
MODEL NUMBER
028698-0070A
COUPLING
(LESS SPRAY)
A952459-0020A
TRANSFER
ROD ASSEMBLY
M909825-YYY0A
TRANSFER KNOB
A994053-0070A
CARTRIDGE
DECK-MOUNT BATH FILLER
CHROME
SATIN NICKEL
OIL RUBBED BRONZE
002
295
224
Replace the "YYY" with
appropriate finish code
7186.900
7186.901
FLUENT™
M964926-YYY0A
LEVER HANDLE (LEFT)
M964927-YYY0A
LEVER HANDLE (RIGHT)
M965623