American Standard 6047.8 Series User manual

Installation Instructions
Installation Instructions
(In Toronto Area only: 1-905-3061093)
Certified to comply with:
• ASSE 1037
• CSA B125.3
• ADA Compliant
© 2013 AS America, Inc.
NOTE TO INSTALLER: Please give this manual to the customer after installation.
MANUAL FLUSH VALVE
with BEDPAN WASHER
M965403 REV. 1.4
MODEL NUMBERS
To learn more about American Standard Faucets visit our website at: www.americanstandard.com
or U.S. customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-3061093)
6047.8XX
6047.8006047.860 (1.6gpf)
6047.820 (1.28gpf)
6047.821 (1.28gpf)
6047.861 (1.6gpf)
6047.815
For Use with 1-1/2"Top Spud Toilets

1
Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.
1. Remove the Bedpan Washer items from the carton. The illustration below shows all items
after they have been removed from the carton. Some items may be packaged partially
assembled to other items.
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
M965403 REV. 1.4
1
1
2
3
49
7
5
6
1. Flush Valve Assembly
(6047.820/.821) (6047.860/.861)
2. Down Tube and Vacuum Breaker
3. Diverter assembly
4. Straight Tailpiece
5. Spud Coupling Nut and Washers
6. Spud Flange
7. Wall Support
8. Installation Instructions
9. 1-1/2" Offset Tailpiece (6047.861/.821/.815)
All American Standard Products Are Water Tested At Our Factory.
Some Residual Water May Remain In The Valve During Shipping.
UNPACKING
8
Installation Instructions
Installation Instructions
(In Toronto Area only: 1-905-3061093)
Certified to comply with:
• ASSE 1037
• CSA B125.3
• ADA Compliant
© 2013 AS America, Inc.
NOTE TO INSTALLER: Please give this manual to the customer after installation.
MANUAL FLUSH VALVE
with BEDPAN WASHER
M965403 REV. 1.4
MODEL NUMBERS
To learn more about American Standard Faucets visit our website at: www.americanstandard.com
or U.S. customer's e-mail us at: [email protected]
For Parts, Service, Warranty or other Assistance,
please call 1-800-442-1902 (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-3061093)
6047.8XX
6047.8006047.860 (1.6gpf)
6047.820 (1.28gpf)
6047.821 (1.28gpf)
6047.861 (1.6gpf)
6047.815
For Use with 1-1/2"Top Spud Toilets

RECOMMENDED TOOLS; Fig. 2 Fig. 2
1.
2.
3.
4.
5.
Flat Blade Screwdriver
Smooth Jaw Adjustable Wrench
Tape Measure
Tubing Cutter
File
12
3
4
5
PRIOR TO INSTALLATION
• Flush all water lines prior to operation.
• DO NOT use pipe sealant or plumbing grease on any coupling!
• Protect the chrome or special finish on the Bedpan Washer.
DO NOT USE toothed tools on finished surfaces to install or
service these valves. Also see “Care and Cleaning” section of
this manual.
IMPORTANT:
• All plumbing must be installed in accordance with
applicable codes and regulations.
• Water supply lines must be sized to provide an
adequate volume of water for each fixture.
• Water pressure over 80 psi is not recommended
with most plumbing fixtures
2
Fig. 1
Roughing-in Dimensions GENERAL DESCRIPTION:
10'
FLUSH VALVE with BEDPAN WASHER
M965403 REV. 1.4
For Use with Exposed Flushometer
and 1-1/2" Top Spud Toilets
38mm (1-1/2")
OFF-SET
TAILPIECE
FOR 1-1/2" TOP
SPUD FIXTURES
ADJUSTABLE
245mm
(9-5/8")
MAX. 619mm
(24-3/8")
708mm
(27-7/8")
358mm
(14-1/16")
222mm
(8-3/4")
FINISHED WALL SUPPLY
DN 25mm
(1" I.P.S.)
FINISHED WALL 108mm-133mm
(4-1/4" to 5-1/4")
ADJUSTABLE
207mm
(8-1/8")
MAX.
322mm
(12-11/16")
90˚

3a
3
1. Place the SPUD FLANGE (1) over the spud on
the Fixture.
2. Thread SPUD COUPLING NUT (2) onto Spud. Make
sure SEAL WASHER (3) and FRICTION WASHER
(4) are installed. Do not tighten fully.
INSTALL TAILPIECE and DOWN
TUBE with VACUUM BREAKER;
Fig. 3
1
INSTALL SPUD FLANGE
COUPLING; Fig. 4
2
M965403 REV. 1.4
1
3
2
TAPERED SIDE
DOWN
1. Slide the COUPLING NUT (3) onto the TAIPIECE
(4 or 4a). Place SEAL WASHER (2) with the tapered
side facing down into the COUPLING NUT (3).
2. Thread and tighten COUPLING NUT (3) to
DIVERTER ASSEMBLY (1).
3. Slide COUPLING NUT (3a) onto the DOWN TUBE
(5). Place SEAL WASHER (2a) with the tapered side
facing up into the COUPLING NUT (3a).
4. Thread and tighten COUPLING NUT (3a) to
DIVERTER ASSEMBLY (1).
Fig. 3
4
4a
2a
5
2
1
23
4
Fig. 4
1-1/2" TOP SPUD
TAPERED
SIDE UP
1-1/2" OFF-SET
TAILPIECE
OR

4
1. Install BEDPAN WASHER ASSEMBLY (1) into SPUD
ASSEMBLY (2) on fixture. Push the ASSEMBLY (1)
down until the TAILPIECE (3) seats on the internal stop.
Do not fully tighted SPUD COUPLING NUT (4).
2. TAILPIECE (3) may be cut to obtain the correct
rough-in dimensions for flush valve.
INSTALL BEDPAN WASHER; Fig. 5
3
M965403 REV. 1.4
Fig. 5
2
4
3
1
1
1
4
2
3
Fig. 7
1. Measure from finished wall to first thread of Adapter
or threaded supply pipe (dimension “X”). Cut COVER
TUBE (1) to length (X). Apply Teflon Tape to the
threaded end of the Adapter or supply pipe. Fig. 7a.
2. Push the COVER TUBE (1) into the WALL
ESCUTCHEON (2). Slide both onto the SUPPLY PIPE
(3). Fig. 7b.
3. Push the COVER TUBE (1) in, to expose the threads
of the supply pipe. Fig. 7c. With a wrench thread the
SUPPLY STOP (4) onto the SUPPLY PIPE (3). Align
and tighten. Fig. 7c.
4. Pull COVER TUBE (1) against SUPPLY STOP (4)
and push WALL ESCUTCHEON (2) against finished
wall. Fig. 7c.
INSTALL COVER TUBE, WALL
ESCUTCHEON and SUPPLY STOP;
Fig. 7
5
TEFLON TAPE
FINISHED WALL
INSTALLATION OF FLUSH VALVE
(6047.820 / 6047.860 Only)
Fig. 6
CAUTION Turn water supplies off
before beginning
Note: Install Optional Sweat Solder Adapter
(Supplied) for copper pipe supply line. Fig. 6.
1. Measure the distance (A) from the finished wall to the
center of the inlet spud on the fixture.
2. Cut the supply pipe 1-1/4" (A-B=C) shorter then the
measurement taken in Step 1. File any rough edges off
the end of the supply pipe.
3. Clean the end of the supply pipe. Push the threaded
Adapter on until it is seated against the internal stop.
Sweat the Adapter to the pipe.
4
CENTER LINE OF
FIXTURE SPUD
FINISHED WALL
FILE EDGES
SOLDER
ADAPTER
Fig. 6
ADAPTER
32mm
(1-1/4)
A
(A-B)= B
C
X
X
CLEAN
Fig. 7a
Fig. 7b
Fig. 7c
2

M965403 REV. 1.4
1. Determine required length of SUPPORT BRACE (1) by
measuring the distance between finished wall and back
of the DIVERTER VALVE (2) at support rod hole. Add
1/4" (6mm) to the length determined and cut the
SUPPORT ROD (5) to size.
2. Rotate the DIVERTER VALVE (2) to allow threading
SUPPORT ROD (5) into back of diverter body. Slide
wall SUPPORT ROD FLANGE (3) onto SUPPORT
ROD (5) and rotate the DIVERTER VALVE (2) so that
the wall SUPPORT ROD FLANGE (3) is flush with
the wall.
3. Using the SUPPORT ROD FLANGE (3), mark the two
holes on the finished wall for the mounting screws and
anchors. Rotate the DIVERTER VALVE (2) to the side
and drill two 5/16" holes in the finished wall 1-1/4" deep.
4. Rotate the DIVERTER VALVE (2) and align the
SUPPORT ROD FLANGE (3). Secure the FLANGE
with two Anchors and Screws (not provided). Tighten
SET SCREW (4). Once aligned correctly, use a
wrench to tighten couplings to make water tight
connections.
INSTALL SUPPORT BRACE;
Fig. 9
Fig. 9
1
5
3
1
4
2
FINISHED
WALL
X+1/4" (6mm)
CUT
THIS END
ANCHORS
SCREWS
X+1/4" (6mm)
5
7
6
2
5
8
121mm, 13mm
(4-3/4)( 1/2)
Fig. 8a
1. As shown in Fig. 8, insert the side INLET FLANGE (1)
on the FLUSH VALVE (2) into the SUPPLY STOP (3).
Lubricate the INLET FLANGE O-RING (4) with water if
necessary. Lightly tighten COUPLING NUT (5). Fig. 8.
Important: Do not use lubricants (other than water)
or any type of thread sealing paste or tape.
2. Align the FLUSH VALVE (2) (Fig. 8a) directly above
the DOWN TUBE (7) and VACUUM BREAKER
COUPLING NUT (6).
Note: There is a 13mm, ( 1/2) tolerance for the
121mm (4-3/4) dimension. Fig. 8a.
3. Pull the DOWN TUBE (7) up to meet the threaded
FLUSH VALVE CONNECTION (8) and hand tighten
the VACUUM BREAKER COUPLING NUT (6). Align all
components of the flush valve assembly. Fig. 8a.
4. Lightly tighten the COUPLING NUT (5) connection
first, then the VACUUM BREAKER COUPLING NUT
(6) and finally the SPUD COUPLING NUT (9). Fig. 8a.
INSTALL FLUSH VALVE;
Fig. 8 & 8a
6
7
3
2
5
1
4
Fig. 8
+
–
+
–
+
–
+
–
9

M965403 REV. 1.4
10
6
Fig. 10
1. Remove COVER (1) from SUPPLY STOP (2). Make
sure supply stop is closed.
2. Remove FLUSH VALVE CAP (3). Pull out PISTON (4).
Replace FLUSH VALVE CAP (3) and tighten.
3. With a flat blade screwdriver open SUPPLY STOP (2).
to flush line of any debris or sediment.
4. Close SUPPLY STOP (2). Remove FLUSH VALVE
CAP (3). Replace PISTON (4). Replace FLUSH VALVE
CAP (3) and tighten.
FLUSH OUT SUPPLY LINES; Fig. 10
8
REMOVE COVER
2
1
CLOCKWISE
CLOSES CONTROL STOP
COUNTER-CLOCKWISE
OPENS CONTROL STOP
3
4
Fig. 12
IMPORTANT: To avoid overflowing, the SUPPLY STOP
(3) must never be opened to the point where the flow
from the valve exceeds the flow capacity of the
fixture. The fixture and drain must be able to handle a
continuous flow in case of a flush valve failure.
Valve is designed to provide stated flush volume with
a 25 GPM flow rate.
1. Remove COVER (2) from SUPPLY STOP (3).Turn on
water supply 1/4 turn to 1/2 turn(CCW) and test for leaks.
Note: Unit may flush for approximately 5 to 10 sec.
when water is first turned on.
2. Actuate the FLUSH VALVE by pulling handle down.
3. Adjust SUPPLY STOP (3) after each flush until the
stated flush volume is achieved, no splashing occurs and
the fixture is properly cleansed.
4. When adjustment is complete, replace COVER (2)
and tighten to ensure vandal-resistance.
ADJUST SUPPLY STOP; Fig. 11
9
1. The FLUSH VALVE can be installed either as a right
or left hand installation.
2. Orientate the FLUSH VALVE as shown in Fig. 12 to
desired position for a left or right hand installation.
LEFT OR RIGHT HAND
INSTALLATION; Fig. 12 Right or Left Hand Installation
Left Hand Right Hand
Fig. 11
2
REMOVE COVER
CLOCKWISE CLOSES
CONTROL STOP
COUNTER-CLOCKWISE
OPENS CONTROL STOP
3

4
7M965403 REV. 1.4
1. Check alignment of FLUSH VALVE (1) and DIVERTER
VALVE ASSEMBLY (2) and fully tighten all connections.
2. Push the DIVERTER ARM and SPRAY (3) down,
parallel to the toilet rim. Flush the toilet to activate the
SPRAY (4).
3. Check all connections for leaks.
4. Return the DIVERTER ARM and SPRAY (3) to the
up-right position.
TEST INSTALLAED BEDPAN
WASHER; Fig. 13 Fig. 13
1
2
3
11