American Standard R910 Flash User manual

- 1 - M965908 (7/18)
Product names listed herein are trademarks of AS America, Inc.
© AS America, Inc. 2018
Thank you for selecting American-Standard...
the benchmark of fine quality for over 140 years.
To ensure that your installation proceeds smoothly-please read
these instructions carefully before you begin.
Flash™
Deck Mount
Tub Systems
Rough Valve Kit
INSTALLATION
INSTRUCTIONS
R900
R910
ROUGHING-IN
1
FINISHED DECK VARIABILITY
ACCOMMODATES DECKING
MATERIAL (TILE, MARBLE,
CORIAN®...) TO 1" THICK
2. FINISHED DECK
3. FITTING MOUNTING SURFACE
4. ACRYLIC BATHS
DECK MOUNTING HOLES
ADJUSTABILITY, TO 1-1/2" THICK
1. DECK THICKNESS
TOTAL DECK THICKNESS
UP TO 2-1/2"
ADJUSTABILITY, TO 1-1/2" THICK
2
3
4
FINISHED
DECK
FITTING
MOUNTING
SURFACE
ACRYLIC
BATH
MOUNTING
1
1/2" COPPER
INLET SUPPLIES
1-3/8" D
MAX.
1-3/8" D MAX.
1-3/8" D
(2) 1-3/8" D
HOLES
(3) 1-3/8" D
HOLES
8" to 12" for Copper tubes
12" for Flex hoses
7-1/8"
1-1/2" D
8" to 12" for Copper tubes
12" for Flex hoses
2MOUNT SPOUT SHANK
SPOUT SHANK LOCK RING FLUSH WITH
TOP OF THREADS ON SPOUT SHANK
SPOUT SHANK
LOCK RING
SPOUT SHANK
FRICTION WASHER
SPOUT SHANK MOUNTING
NUT
1-1/2" MAX.
MOUNTING
SURFACE
PLUG
Certied to comply with ANSI A112.18.1
U.S. Patent No. D403,750
• Drill holes in mounting deck as shown on STEP 1. The maximum allowable deck thickness is 1-1/2".
• Unthread PLUG from SPOUT SHANK.
• Insert the SPOUT SHANK through the mounting deck from below. Assemble the SPOUT SHANK LOCK RING so it
is ush with the top of the threads on the SHANK.
• Tighten SPOUT SHANK MOUNTING NUT securely.
• Thread PLUG into SPOUT SHANK.

- 2 -
3a
NOTE: For unfinished surface use larger VALVE LOCK RING.
NOTE: For finished surface use small VALVE LOCK RING.
Larger VALVE LOCK RING can be used on nished surface for Colony Pro, Quentin,
Estate, Fitzgerald, and Studio S.
• Insert the HOT and COLD VALVE BODIES through the mounting deck from below. The HOT VALVE BODY
is marked with a red label. Assemble the VALVE LOCK RINGS so they are ush with the top of the
VALVE BODIES.
• Tighten the VALVE BODY mounting nuts securely.
• Fasten the VALVE LOCK RINGS to the unnished surface with #8 at screws (Not provided)
• Thread HOSE CONNECTOR (1) onto VALVE BODY (3, 5). Thread HOSE CONNECTOR (2) onto TEE (4).
Tighten HOSE CONNECTOR (1) and (2) rmly.
Note: Hoses have different thread ends. Make sure to connect the fine thread to the Hot/cold valve bodies.
• Insert HAND SHOWER SHANK (6) through mounting deck from top and secure it with MOUNTING NUT.
• Install HOSE and PLUG (7) from above deck.
MOUNT SIDE VALVE BODIES
3
M965908 (7/18)
SMALL
VALVE
LOCK RING
FITTING
MOUNTING
DECK
LARGE
VALVE
LOCK RING
SPOUT
SHANK
HOT
COLD
FRICTION WASHER
MOUNTING NUT
VALVE LOCK RING FLUSH WITH
TOP OF THREADS ON VALVE SHANK
VALVE
BODY
# 8 FLAT
SCREWS
5
1
1
7
6
3
2
2
4
FOR COPPER TUBE INSTALLATION (not supplied)
2
1
5
3
4
NOTE: Remove cartridge to protect from brazing process.
• Remove SLEEVES (1) from the SIDE VALVES and PLUG (5)
from spout shank.
• Remove CARTRIDGES from the Side Valves
(Follow instruction in Step 5 to remove Cartridges )
• Remove VALVE PIPE (2) if installing (R910) or
remove VALVE PLUG (3) if Installing (R900)
• Take INSERTS (4) out from SIDE VALVES
and TEE.
• Cut copper tubes as needed and braze joints.

- 3 -
5
MAKING CONNECTIONS
SERVICE — TO CHANGE THE DIRECTION OF HANDLE ROTATION
• Turn off the water supplies.
• Turn HANDLE to the off position and remove HANDLE.
• Unthread SCREW from CARTRIDGE.
• Remove the SLEEVE from the CARTRIDGE.
• Unscrew the VALVE LOCK NUT and remove.
(17 mm deep socket is required)
• Remove the CARTRIDGE.
• Remove the SPRING CLIP.
• Remove the STOP WASHER. Turn it 90˚ and replace.
• Replace the SPRING CLIP.
• Reverse the above steps to reassembly the components.
• If the spout drips, operate the handles several times
from the off to the on position. Do not force - the handles only turn 90˚
4
M965908 (7/18)
WATER SUPPLY
CONNECTIONS
WATER SUPPLY
CONNECTIONS
1
3
2
4
VALVE
LOCK NUT
SLEEVE
SCREW
VALVE
CARTRIDGE
SPRING
CLIP
STOP
WASHER
90
DEEP SOCKET
17 mm (11/16")
• Connect the water supply lines to the VALVE BODY.
For R910 installation, install HAND SHOWER HOSE (1) to the TEE.
• Insert HAND SHOWER HOSE (1) through HAND SHOWER SHANK (2) and
thread HAND SHOWER HOSE (1) into TEE (4).
• Place HOSE PLUG (3) into HAND SHOWER SHANK (2).

- 4 -
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369
(TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
A911546-0070A
VALVE LOCK NUT
M906666-0070A
LARGE FIXATION NUT
M918464-0070A
SPINDLE
918555-0070A
SCREW
994053-0070A
VALVE CARTRIDGE
M962278-0070A
VALVE MOUNTING KIT
M970512-0070A
VALVE PIPING KIT (R910)
M970511-0070A
VALVE PIPING
PLUG (R900)
M906666-0070A
LARGE
FIXATION
NUT
M906699-0070A
SMALL
FIXATION
NUT
M970510-0070A
HAND SHOWER
HOLDER
(R910)
051343-0070A
HOSE KIT (R910)
A952849-0070A
CHECK VALVE
MODEL NUMBERS
R900 / R910
Flash™
Deck Mount
Tub Systems
Rough Valve Kit
M965908 (7/18)