Amico ARM Instructions for use

Installation Instructions and
Maintenance Manual
Side to Side Monitor (SSM) Arm

Preface
IMPORTANT, PLEASE READ CAREFULLY
Thank you for your purchase with Amico Accessories Inc.
This unit is designed for long lasting performance, providing the end user complies with assembly and maintenance
procedures. This Instruction Manual is your guide to ensure that you get the best performance out of the equipment.
Amico Accessories is not responsible for any damage as a result of (but not limited to) abuse and other problems that
may be a direct or indirect result of failure to comply with the instructions provided in this manual.
Please note these key words and symbols:
WARNING Steps where extra care should be taken to prevent injuries and damage.
NOTE Steps that point out helpful information.
Medical Facility Responsibilities
Preventive maintenance checks must be performed regularly to maintain the quality and performance of this product.
Any parts that may be broken, missing, worn, distorted, or contaminated in any way should not be used and all
affected parts should be replaced immediately. Should the necessity of any repair be suspected; please contact your
local distributor or call 1-877-264-2697.

Table of Contents
Section 1: Installation Preparation 4-6
Installation Tools Requirements 4
Pre-Installation Information 5
Typical Installation Reference for SSM 6
Section 2: Installation on Rail Systems 7-10
Mounting to MRS (Monitor Rail System) 7
Mounting to Hill-Rom Vertical Rail (with the G-Track Adapter (GTA)) 8
Mounting to the VRS (Vertical Rail System) with the V-Adapter 9
Mounting to the Ergotron and Rubbermaid Rail 10
OSHPD Anchor Pre-Approval OPA-1743 10
Section 3: Monitor Installation 11-17
Monitor Mounting 11
Monitor Shelf: 3" (76.2 mm) Top/Back Mount, 5" (127 mm) Top/ Back Mount and VESA 12
Monitor Shelf: 6" (152.4 mm) Drop On 13
Monitor Shelf: Philips Intellivue 14
Monitor Shelf: Welch Allyn 15
Monitor Mounting: VESA 75/100 16
Accessory Shelf: Disc 17
Section 4: Adjustments 18-25
Rotation (SSM Side To Side) 18
Adjusting the Tension Bolt 19
Monitor Tilt 20-21
Rotation (Monitor Head) 22
Portrait and Landscape Adjustment 22
Portrait and Landscape Limiter 23
Cable Management: SSM Cable Management 24
Cable Management: MRS Rail Cover 25
Section 5: Troubleshooting, Maintenance and Product Classification 25-30
Cleaning 25
Troubleshooting 26
Preventive Maintenance (SSM Monitor Arm) 27-28
Part Number Matrix 29-30
Warranty Information 31

4Amico Accessories Inc.
Section 1: Installation Preparation
Installation Tools Requirements
The following table lists all the tools and parts required for installation
NOTE: Amico does not provide any display hardware, nor the tools necessary for assembly (All above in grey text).
NOTE: Tools and the monitor-dependant hardware set are not provided by Amico Accessories Inc.
A B
1
2
3
4
Item Item number Quantity
Phillips screw driver #2 A1 1
Hex keys (1/8" [0.3 cm], 3/16" [0.5 cm], M3, M4) A2 1 each
Socket wrenches (12 mm [1.2 cm],1/2" [0.05 cm]) A3 1 each
Adjustable wrench A4 1
SSM arm B1 1
Mounting adapter/plate (many options)
and Monitor dependant hardware set B2 1
Mounting shelf (0-9, W) B3 1
Extension arm (optional) B4 1

www.amico.com 5
Section 1: Installation Preparation
Pre-Installation Information (Please read carefully before starting)
WARNING: VERIFY THAT RAILS HAVE BEEN INSTALLED IN ACCORDANCE WITH AMICO RAIL INSTALLATION
INSTRUCTIONS. RAIL FAILURE WITH DEVICES MOUNTED CAN CAUSE SERIOUS INJURY AND EQUIPMENT DAMAGE.
WARNING: IT IS DANGEROUS TO USE THE ARM FOR WEIGHTS OUTSIDE OF THE RATED RANGE. STRUCTURAL
FAILURE AND/OR SERIOUS INJURY COULD RESULT.
WARNING: DO NOT POSITION THE SSM MONITOR ARM ABOVE A PATIENT.
WARNING: IT SHALL BE THE RESPONSIBILITY OF THE HOSPITAL, ITS CONSULTANTS AND/OR CONTRACTORS TO
DETERMINE IF THE WALL IS ADEQUATE TO SAFELY MOUNT THE SPECIFIC INSTRUMENT. THIS INCLUDES THE
SELECTION OF APPROPRIATE FASTENERS AND THE PROPER INSTALLATION OF EQUIPMENT, REGARDLESS OF WHAT
IS SUPPLIED WITH YOUR SSM MONITOR ARM. SEE RAIL INSTRUCTIONS FOR SPECIFIC WALL CHANNEL GUIDELINE
INFORMATION.
WARNING: VERIFY THE WEIGHT OF THE DEVICE TO BE MOUNTED. SINGLE ARM SSM MONITOR ARMS ARE RATED
FOR 30 LBS (13.6 KG), DUAL ARM SSM MONITOR ARMS ARE RATED FOR 15 LBS (6.8 KG). PLEASE REFER TO WEIGHT
RATING LABEL, LOCATED EITHER ON THE TOP OR BOTTOM OF THE ARM ASSEMBLY, DEPENDING ON THE MODEL.
CHECK THAT THE DEVICE TO BE MOUNTED DOES NOT EXCEED THE WEIGHT RATING. SERIOUS INJURY AND
DAMAGE TO THE ARM CAN OCCUR AS A RESULT OF OVERLOADING THE ARM ASSEMBLY.
For installation on non-Amico rails, ensure the rail is safe for the application.
If you are unsure about any part of the installation process or product use, please contact an Amico Accessories
product Specialist: 1-877-264-2697
Considerable efforts have been made to ensure the safety of your hospital staff and your patients. The installation itself
is beyond the control of Amico Accessories. Accordingly, Amico Accessories will not be responsible for failure related to
the installation of the product.
HAVE A PRODUCT QUESTION? GIVE US A CALL AT: 1-877-264-2697

6Amico Accessories Inc.
Typical Installation Reference for SSM
The diagram below illustrates the components referenced in relation to one another in the installation of the SSM
Monitor Arm. Please follow the instructions outlined herein to ensure proper installation.
SSM MONITOR ARM
1. Monitor Mounting Adapter
VESA LCD mount shown, other options available
2. Monitor Head - Rotation
Monitor rotation adjustment
3. SSM Joint
Rotates the monitor head to the desired position
4. MRS Adapter
Adapter for the MRS rail
5. Cable Management
Manages the cables of the monitor for better organization
Section 1: Installation Preparation
SSM MONITOR ARM
1. Monitor Mounting Adapter
(Pg.12-18)
VESA LCD mount shown, other options available
2. Monitor Head - Rotation (Pg. 22)
Monitor Rotation Adjustment
3. SSM Joint (Pg. 20)
Rotates the Monitor Head to the desired
position
4. Mounting Adapter (Pg. 6-9)
MON adapter shown for MRS rail
5. MRS Adapter (Pg. 9)
Adapter for the MRS Rail
6. Cable Management (Pg. 25)
Manages the cables of the Monitor for better
organization.
1
2
3
4
5
6
1
23
4
5
6

www.amico.com 7
Section 2: Installation on Rail Systems
WARNING: DO NOT ATTEMPT TO MOUNT/REMOVE THE ARM FROM THE RAIL
WHEN LOADED WITH ANY INSTRUMENT
Mounting to the MRS (Monitor Rail System)
WARNING: SUPPORT SSM ARM UNTIL THE SET SCREWS ARE
TIGHTENED, SSM ARM CAN SLIDE DOWN WHEN SET SCREWS ARE
NOT TIGHTENED.
NOTE: Top and bottom stoppers prevent the adapter from sliding
out of the MRS. To remove, the adapter must be removed from
the top with the top stopper pressed into the rail (Figure 2).
NOTE: To slide the arm vertically in the channel, lift the arm near
the monitor and push up or down at the adapter (Figure 1).
1. Support the bottom of the arm with one hand, guide the adapter
into the top of the channel (Figure 1).
2. Once the arm is at the desired height, tighten the two set screws
located at the bottom of the adapter using a 1/8" (3 mm) HEX key.
DO NOT release the SSM Monitor Arm until the two set screws
are tight. The SSM Monitor Arm may slide down the rail if the set
screws are not tightened.
Figure 2
Bottom
Stopper
Top Stopper
MRS Rail: Length for representational use only
Figure 1
1/8" (3 mm)
set screws
SSM Arm
Standard MON
Channel Adapter
MRS Rail

8Amico Accessories Inc.
Section 2: Installation on Rail Systems
Mounting to Hill-Rom Vertical Rail (with the G-Track Adapter (GTA))
WARNING: TO PREVENT THE ADAPTER FROM FALLING DOWN THE CHANNEL, ENSURE THAT THE SCREWS ARE
FASTENED AS TIGHT AS POSSIBLE. AFTER INSTALLATION, ROTATE THE SSM ARM SIDE TO SIDE AND VERIFY NO
MOVEMENT IS PRESENT BETWEEN THE ADAPTER AND THE RAIL.
WARNING: REMOVAL OF LOCK NUTS WILL REQUIRE A NEW SET FOR REINSTALLATION. PLEASE CONTACT AMICO
ACCESSORIES FOR SPARE PARTS, 1-877-264-2697.
NOTE: Before installing, ensure two regular nuts and two lock nuts are loosened to the tip of the G-adapter
screws. This will allow the head of the G-adapter screws to adjust into the profile of the Hill-Rom rail (Figure 3).
1. Support the bottom of the SSM Arm and guide the head of the top screw into the opening of the rail
(Figure 1 and 2).
2. Ensure the flange on the GTA is properly aligned with the rail. Slide the GTA up so that the head of the bottom
screw slides into the opening of the rail (Figure 3).
3. Position the SSM Arm at the desired height. Tighten the two regular nuts and then the two lock nuts on the top and
bottom of the adapter using a 12 mm socket wrench.
4. Cover the nuts with the two plastic caps provided (Figure 4).
Figure 1
Hill-Rom
Rail
Front
Opening of
the rail
Jam nut,
lock nut, and
plastic cap
Figure 3
Side of the G-Adapter
12 mm nuts,
lock nuts
Flange
Backside
Head of
the top GTA pin
Head of the
bottom GTA pin
Figure 2
G-adapter Screw
Figure 4
Plastic caps

www.amico.com 9
Section 2: Installation on Rail Systems
Mounting to the VRS (Vertical Rail System) with the V-Adapter
WARNING: TO PREVENT THE V-ADAPTER FROM FALLING DOWN THE CHANNEL, ENSURE THAT THE SCREWS ARE
FASTENED AS TIGHT AS POSSIBLE. ROTATE SSM ARM SIDE TO SIDE AFTER INSTALLATION TO VERIFY NO
MOVEMENT IS PRESENT BETWEEN THE ADAPTER AND THE RAIL.
NOTE: Before installation, ensure two nuts and two knobs are loose to the tip of the V-adapter screws. This will
allow the head of the V-adapter screws to adjust into the profiles of the vertical rail.
1. Angle the SSM Arm from either side and guide the heads of the top and bottom screws into the channel of the rail
(Figure 1-3)
2. Ensure the flange on the adapter is properly aligned with the rail.
3. Position the arm to the desired height and fasten two knobs and two nuts (12 mm) to the tightest possible position.
Cover the nuts with the two plastic caps provided (Figure 4).
Figure 1 Figure 4
Vertical Rail
End Cap
Screw Knobs
Tighten thumb
screws and nuts
Flange
Backside
Head of
the top screw
Head of the
bottom screw
Figure 2
V-adapter Screw
Figure 3
Side of the
V-adapter
Side of
the VRS

10 Amico Accessories Inc.
Section 2: Installation on Rail Systems
OSHPD Anchor Pre-Approval OPA-1743
Mounting to the Ergotron and Rubbermaid Rail (15 lbs [6.8 kg] max. weight capacity)
WARNING: TO PREVENT THE SSM ARM FROM FALLING DOWN THE CHANNEL, ENSURE THAT THE TWO NUTS ARE
FASTENED AS TIGHT AS POSSIBLE.
NOTE: COW-adapter will work both with Ergotron and Rubbermaid rails. Set the slider horizontally to insert the
adapter to the Rubbermaid rail, and set the slider vertically to insert the adapter to the Ergotron rail (Figure 1:
Rubbermaid) (Figure 2: Ergotron).
NOTE: Before installing, ensure two nuts are loosened to the tip of the screws. This will allow the sliders to adjust
into the profile of the rail.
1. Remove the cap from the top of the rail.
2. Ensure the sliders are vertical for the Ergotron or horizontal for the Rubbermaid rail.
3. Align the sliders with the slot on the rail and slide the adapter into the slot from the top of the rail (Figure 4 and 5).
4. Position the adapter to the desired height and tighten the nuts. Replace plastic caps on to the nuts.
Figure 1 Figure 2 Figure 3
Sliders set
horizontally for the
Rubbermaid rail
Sliders set
vertically for the
Ergotron rail
Figure 4 Figure 5
Top of the
Ergotron
Ergotron rail shown
COW - Rail
Slot
COW - Rail
Slot
Plastic caps
COW - Rail
In compliance with standards established for the anchor and installation of instrument support systems by the
California Office of Statewide Health Planning and Development (OSHPD), Amico Accessories Inc. has obtained
preapproval for MRS 19" (482.6 mm) Wall Channels or longer with extension Arm. For proper installation requirements
please refer to our OPA document.

www.amico.com 11
Section 3: Monitor Installation
Monitor Mounting
WARNING: ENSURE THAT THE ARM IS IN THE HIGHEST POSITION AND IS LOCKED BEFORE MOUNTING OR
REMOVING THE ARM FROM THE CHANNEL.
WARNING: ENSURE THE MONITOR SHELVES/PLATES PROVIDED BY AMICO ACCESSORIES INC. OR OTHER
MANUFACTURERS ARE ASSEMBLED AS DIRECTED AND MATCH THE SHELF REQUIREMENT. IF A MONITOR SHELF/
PLATE DOES NOT MATCH THE REQUIREMENT, PLEASE CONTACT AMICO ACCESSORIES INC. AT 1-877-264-2697
NOTE: Amico Accessories Inc. carries a variety of Mounting Shelves and adapters that attach to the SSM Arm. View
the SSM Matrix on pages 29 and 30 for more information.
NOTE: SSM - XXY - (C) – (Z) - Variables X, Y, C and Z are placeholders for part classification. Please refer to the SSM
Matrix on pages 29 and 30 for more information.

12 Amico Accessories Inc.
Section 3: Monitor Installation
Monitor Shelf: 3" (76.2 mm) Top/Back Mount, 5" (127 mm) Top/ Back Mount and VESA
WARNING: ENSURE THE MOUNTING SHELF IS SECURELY LOCKED AND HORIZONTAL TO PREVENT THE MONITOR
FROM SLIDING AND FALLING (SEE PAGE 20).
WARNING: ON THE BOTTOM OF THE MOUNTING SHELF THERE IS A PLUNGER THAT SECURES THE SHELF TO THE
MOUNTING ADAPTER. SIMPLY PULL DOWN ON THE PLUNGER, ALIGN THE ADAPTER PLATE WITH THE SHELF AND
RELEASE THE PLUNGER ONCE POSITIONED OVER THE CLEARANCE HOLE (FIGURE 3).
NOTE: The plunger can be locked in the open position by pulling and twisting it.
1. First install the mounting adapter to the device (Please refer to the adapter installation manual provided with the
adapter) (Figure 1 on previous page).
2. Loosen the plastic screws on the bottom side of the mounting shelf. Pull down on the plunger lock at the bottom of
the mounting shelf and twist it to keep it open. Slide the adapter laterally onto the mounting shelf until the plunger
aligns with the clearance hole at the front of the mounting adapter (Figure 3).
3. Release the plunger and tighten the plastic screws by hand (Figure 4).
Mounting shelf
Monitor
Mounting
adapter
Front of the
mounting
adapter
Monitor
dependant
hardware
Figure 1 Figure 2
Mounting shelf
Front of
the shelf
Plunger Lock
5" (127 mm) mounting shelf is shown above
Plastic
Screws
Plunger released
Plunger pulled
Figure 3 Figure 4

www.amico.com 13
Section 3: Monitor Installation
Monitor Shelf: 6" (152.4 mm) Drop On
WARNING: Ensure the mounting shelf is secure and vertical to prevent the monitor from sliding and/or falling.
NOTE: Quick installation system: On the back of the mounting plate there is a plunger that secures the plate to
the mounting adapter. Simply slide and align the adapter to the shelf and the plunger will automatically engage
and lock.
1. First, install the mounting adapter to the back of the monitor (Please refer to the adapter installation manual
provided with the adapter).
2. Lift the monitor and slide the mounting adapter plate on to the mounting shelf. Slide the monitor down until
the mounting hole on the mounting adapter aligns with the plunger (Figure 1). When the hole and the plunger
are perfectly aligned the plunger will automatically lock. If the plunger does not lock automatically then lock the
plunger manually by turning it. Tighten the locking screws by hand to the tightest possible position (Figure 2).
Figure 1 Figure 2
Mounting
shelf
Plunger Lock
Locking screws
Mounting adapter
plate
Mounting hole

14 Amico Accessories Inc.
Section 3: Monitor Installation
Monitor Shelf: Philips Intellivue
WARNING: ENSURE THE MOUNTING SHELF IS FIRMLY LOCKED AND HORIZONTAL TO PREVENT THE MONITOR
FROM SLIDING AND FALLING.
NOTE: Philips recommends a Maximum tilt of 15°.
NOTE: It is recommend to use M6 x 20 mm screws with thread locker or patched screws in order to eliminate
possible dangers.
1. Attach the table top mount from Philips (not supplied by Amico) to the mounting shelf by securing the 3 screws
through the shelf (Figure 2).
2. Place the monitor to the table top mount until it clicks (Figure 3).
3. Tilt the monitor to the desired angle and re-adjust the tension as needed with a 12 mm wrench (Figure 4).
Philips Table Top Mount
(not supplied)
12 mm hex nut
To tighten
To loosen
Three 20 mm
M6 screws
Table top
mount
Mounting shelf
Figure 1 Figure 2 Figure 3 Figure 4

www.amico.com 15
Section 3: Monitor Installation
Monitor Shelf: Welch Allyn
WARNING: ENSURE THE MOUNTING SHELF IS SECURE AND HORIZONTAL TO PREVENT THE MONITOR FROM
SLIDING AND FALLING.
1. To attach the monitor to the Welch Allyn shelf, lift the monitor to match the front lip of the mounting plate. Slide the
monitor laterally until the mounting hole on the monitor aligns with the thumb screw on the adapter (Figure 1).
2. Tighten the thumb screw to the tightest possible position (Figure 2).
Figure 1 Figure 2
Thumb screw
Front lip
Thumb screw

16 Amico Accessories Inc.
Section 3: Monitor Installation
Monitor Mounting: VESA 75/100
NOTE: Setting the VESA shelf horizontally can make the mounting procedure easier.
NOTE: If the original monitor bolts are too large, determine the screw size and consult with Amico Accessories Inc.
1. Determine the monitor mounting configuration. VESA 75 (75 mm x 75 mm with M4 threads) or VESA 100 (100 mm x
100 mm with M4 threads).
2. If a VESA 75 configuration is present on the monitor then lift the monitor to match the mounting holes on the VESA
75 shelf (Figure 1). Fasten two M4 screws by hand through the back of the VESA 75 shelf and into the rear of the
monitor. Secure the two remaining screws through the holes on the back of the VESA 75 shelf and into the monitor.
Ensure all screws are secured. Be sure not to force the screw in, as it may strip the head. The VESA 100 adapter will
not be required. Tighten using a cross pattern.
3. If a VESA 100 configuration is present on the monitor then attach the back of the VESA 100 adapter to the front of
the VESA 75 shelf. This is done by inserting four M4 screws through the holes on the back of the VESA 75 shelf, into
the inner threads from the back of the VESA 100 adapter (Figure 2 and 3) Lift the monitor to match the mounting
holes on the VESA 100 adapter. Secure four M4 screws provided by the monitor manufacturer through the back
of the VESA 100 adapter and into the monitor. Ensure all screws are secured; be sure not to force the screw in, as it
may strip the head. Tighten using a cross pattern.
Figure 1 Figure 2 Figure 3
M4 screws for VESA
Front of the VESA 100 adapter
M4 inner
threads
M4 mounting hole
Screws
VESA 75
VESA 100
Side of the VESA 75 and VESA 100 together
M4 mounting hole
Front of the VESA 75 shelf

www.amico.com 17
Section 3: Monitor Installation
Accessory Shelf: Disc
NOTE: It is possible to attach accessories to the top or bottom side of the SSM Arm using this same mount
(Figure 1).
NOTE: Amico Accessories Inc. carries a variety of different accessories that attach to the head of the SSM Arm.
Figure 1
Figure 5
Figure 2
Figure 6
Figure 3
Figure 7
Figure 4
Figure 8
6" and 12" post
(152.4 mm and 304.8 mm)
Single or dual
cord holder
Keyboard
handle
Screw type:
10 x 32
Top side Bottom side
(Disc installed on the top and Disc
installed on the bottom)
Dual Head Keyboard Tray Laptop Holder ARS Rail

18 Amico Accessories Inc.
Rotation (SSM Side To Side)
WARNING: BOTH ARMS HAVE A 180° ROTATION.
ENSURE PROPER CLEARANCE AROUND THE
ARM(S) TO AVOID COLLISION.
NOTE: If the arm becomes difficult to rotate, or
too loose, please contact Amico Accessories Inc.:
1-877- 264-2697.
Single Arm Rotation:
To rotate the arm, simply push on the side of the arm or the mounted monitor in the direction desired (Figure 1).
Dual Arm Rotation:
To rotate at the end point (near wall), push on the side of the extension arm, near the mid-way point (Figure 2). To
rotate at the midway point, hold the extension arm with one hand and push on the side of the SSM Arm with the
mounted monitor in the direction desired (Figure 3).
Section 4: Adjustments
Figure 5
12
3
4
DETAIL 1
SCALE 1 : 5
DETAIL 2
SCALE 1 : 5
DETAIL 3
SCALE 1 : 5
DETAIL 4
SCALE 1 : 5
Detail 1
Scale 1:5
Detail 2
Scale 1:5
Detail 3
Scale 1:5
Detail 4
Scale 1:5
Figure 4
Arm rotated
Figure 1
To rotate at first arm
First arm rotated
Figure 2
Second arm rotated
To rotate at second arm
Figure 3
End point
End point
Midway point

www.amico.com 19
Adjusting the Tension Bolt
WARNING: It is not recommended to adjust the rotation tension bolt. If you do, be sure not to unfasten the bolt
too much or the head will disassemble from the arm.
WARNING: Be sure not to adjust rotation tension bolt at the bottom end of the arm. This may damage the
hardware inside the head.
1. The rotation tension bolt is located under the front-end of the arm. This is where the tension of the heads rotation
is adjusted (Figure 1).
2. The mounted device rotates at the front of the arm. To rotate the device, push the corners of the device or the head
(Figure 2 and 3).
Section 4: Adjustments
1/2" (12.7 mm) bolt
Rotation Tension
Point
Figure 1 Figure 2 Figure 3
Head Rotated SSM Head without Rotation

20 Amico Accessories Inc.
Section 4: Adjustments
Monitor Tilt
WARNING: ALWAYS SUPPORT THE MONITOR IF ADJUSTING THE TILT ANGLE WHILE A MONITOR IS MOUNTED.
WARNING: FOR HEAVIER MONITORS, IT IS STRONGLY RECOMMENDED TO CHECK WHETHER THE TILT-SETTING
LEVER IS TIGHTENED TO THE TIGHTEST POSITION WHILE THE MONITOR IS ATTACHED. IF THE ADJUSTMENT LEVER
CANNOT BE TIGHTENED ENOUGH TO SECURE THE MONITOR IN PLACE, PROCEED TO STEP 3.
WARNING: DO NOT ADJUST TILT-ANGLE WITHOUT FIRST LOOSENING THE TILT-SETTING LEVER.
NOTE: Tilt-angle setting is ONLY ACHIEVED BY TIGHTENING THE TILT-SETTING LEVER. DO NOT tighten nuts
adjacent to the Tilt-setting Lever.
Tilt Hinge Tilt-Setting Lever
4 mm (5/32")
Allen Nut
Patient Monitor
Shelf
1. To TIGHTEN the Tilt-Hinge (in order to set the desired tilt angle), TURN the Tilt-Setting Lever CLOCKWISE. [Turning
the Lever COUNTER-CLOCKWISE will ENABLE tilt movement]
4 mm Allen Key 12 mm Socket Wrench
Tools Reference
Tighten Loosen