Amico Majestic Series User manual

Corporation
Installation Instructions
Horizontal Headwall
Majestic Series Single Tier

Caution
Please do not lift headwall by the plastic end caps
1. Review a copy of the nal approved shop drawing(s) and/or submittal package. These docu-
ments will provide you with technical information specic to your installation, such as:
• equipment types and quantities
• room numbers and location
• shop drawings of each unit type
• wiring diagrams and rough-in locations
2. Locate the headwall unit from the shipping boxes that you wish to install.
The contents of each shipping box are listed on the shipping document(s).
For Seismic Installation:
See Page 7
Before Installation
2Amico Architectural
Note
The installation instructions provided are for the Amico standard products. Slight modications
to the installations may be required. The product shipped to the job site may not be exactly as
shown on the installation drawings.
Headwall installation should conform to local building codes

www.amico.com 3
Installation
1. Using shop drawings, mark both devices center line AFF (above nished oor) on wall.
2. Mark horizontal line for bottom of mounting bracket (to be installed later). This line is to be o-
set 4" (102 mm) above devices center line.
devices center line AFF
Unit shown for reference only
Note
4
devices center line AFF
bottom of mounting
bracket line AFF

4Amico Architectural
Installation
3. Using a stud locator, mark the location of any metal studs in the building wall that intersect the
headwall mounting location.
stud
drywall
stud reference line
wall
nished oor
4. Mount the bracket(s) on the wall using hardware compliant to local building codes (supplied
by others). Align bracket(s) horizontally according to headwall mounting location. Refer to
drawings. Bracket includes I.D. Marks for locating holes vertically, which are to be drilled on-site
according to location of studs. Remember to align bottom of bracket to“bottom of bracket” line
marked in step “2”.
bottom of
mounting
bracket line
bracket
I.D. mark for holes
bottom of
mounting
bracket lines

www.amico.com 5
Installation
5. Check rough-in drawing(s) for electrical rough-in locations. Remove any device cover plates
preventing removal of fascia, if necessary, then remove fascia panel(s) for access to rough-in
locations.
6. Remove center and lower cover of headwall to expose medical gas pipes (on units having gases)
and lower mounting area.
typical rough-ins

6Amico Architectural
Installation
7. Hang the headwall unit on the wall, over the mounting bracket, and center the unit with refer-
ence to bed center line. Verify rough-in locations in wall and align with rough-in provisions on
headwall.
8. Make all necessary medical gas and electrical connections at rough-in locations.
9. Secure headwall to the wall through lower section using hardware compliant to local building
codes (provided by others). Lower bracket is to be drilled on-site according to stud location.
Replace lower headwall cover when done.
10. Replace any fascia panels and covers removed in step 5 and 6.
End plate and cover removed in this
view to show detail. Do not remove!
Note
lower mounting locations

www.amico.com 7
Seismic Installation
For Seismic Installation
1. Backing plate shall be minimum 16 ga. steel along the full width of headwall, and attached to
building structure using #12 tek screws
2. Headwall shall be attached to backing plate using #12 tek screws at 16" o.c.

C US LISTED
Amico Architectural | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
71 East Industry Court, Deer Park
NY 11729, U.S.A
Toll Free Tel: [phone]
Toll Free Fax: [phone]
Tel: [phone]
Fax: [phone]
Email: [e-mail] INSTALL INSTR. MAJESTIC SNGL TIER HORIZ HDWL 2011
www.amico.com