&Tradition Hee Welling Drip HW61 User manual

Congratulations with your new Drip table, designed in
2021 by Hee Welling. We hope you will enjoy using this
product and follow these instructions to ensure correct
assembly. If you have any questions or comments,
please do not hesitate to contact us by mail on:
in[email protected]
Drip HW61-HW64
Hee Welling
2021
User instructions

Please read these instructions carefully and retain them
for future reference to ensure that the product is used
correctly. For your own safety, please study each step of
this instruction manual first. &Tradition is not responsible
for any faults or damages caused by not following these
instructions correctly. Do not modify this product in
any way.
Contents
ATabletop
B Legs x 4
CCorners x 4
D Long frames x 2
EShort frames x 2
F Middle crossbar
GEnd-crossbars x 2
HAdaptor x 6
ILong hex screws x 12
JShort hex screws x 12
KFlat head hex screws x 16
LShort button screws x 14
MLong button screws x 8
NAllen key x 3
OCover components x 4
PHex socket head cap screws x 8
Safety precautions
- Dispose of plastic bag from packaging and do not allow
children to play with it.
- The table is only intended for indoor use.
- Handle tabletop with care in order not to scratch surfaces.
- Two or more adults are required when lifting the table.
Drip HW61-HW64
Hee Weeling
2021
Cleaning instructions
Laminate can be cleaned with a soft cloth wrung in a mild
solution of lukewarm water and an universal cleaning
detergent. Always wipe with a dry soft cloth after cleaning.
For difficult stains such as coffee or tea use a nylon
bristle brush with mild household cleaner or detergent,
rinsing with clean water and repeating as necessary. Rinse
thoroughly with water.
Aluminium (powder coated or polished) can be cleaned
using a soft cloth wrung in lukewarm water. Always dry
immediately with a soft cloth. Avoid use of abrasive
cleaning products such as steel wool as this will cause
damage to the surface.
A
B
D
C
E
F G
H I J
K L M
N O P

Step 1
Insert the corners (C) into the frames (D & E)
as shown and attach them with screw (K).
The two small holes on the corners (C) must
be facing upwards - see illustration.
Important: Only install the screws slightly
and then finally tighten all of them.
Step 2
Install one adaptor (H) in the lower middle
part of each leg (B) using two long hex
screws (I). Make sure to place adaptor in the
correct direction - see illustrations.
Step 3
Connect one adaptor (H) in the middle of
each end-crossbar (G) using two long hex
screws (I). Please make sure that the adaptor
(H) and the crossbars are facing in the
correct direction - see illustration.
Step 4
Connect the crossbar (G) to two legs using
the short hex screws (J).
BG
H
J
A
D
DETAIL D
SCALE 1 : 5
A A
B B
C C
D D
E E
F F
G G
H H
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:10 SHEET 1 OF 1
A2
WEIGHT:
HW62_1900x800x950
N
K
I
B
Correct Incorrect
H
I
H
G

Step 5
Attach the middle crossbar to (F) and
make sure that the holes are in the correct
direction - sew illustration.
Step 6
Place the leg-section on the frame upside
down and align all four legs in each corner (C).
Screw two long button screws (M) in each
corner to connect them.
F
J
Step 7
Place the cover components on each of the
4 corners (C) and attach them with screws (P).
Step 8
Place the tabletop (A) upside down on a soft,
flat surface and place the frame on top,
upside down.
Important: Install only the screws (L) slightly
and then finally tighten all of them to secure
correct fit.
Finally, flip the table and enjoy your product.
B
C
M
B
O
P
DE
A
L

andtradition.com