&Tradition JAIME HAYON MEZCLA JH20 User manual

USER INSTRUCTIONS
Congratulations on choosing this original Mezcla
table, designed in 2018 by Jaime Hayon. We
hope you will enjoy using this product and
follow these instructions to ensure correct
assembly. If you have any questions or comments,
please do not hesitate to contact us by mail on:
[email protected]
MEZCLA JH20 -JH22
BY
JAIME HAYON
2018

CONTENTS
A- Base
B- Top support
C - Column
D- Table top
E - Large bolts x 3
F - Large counter sunk bolts x 3
G - Flanged button head screws x 6
H - Large Allen key
I - Small Allen key
J - Self-adhesive felt pads x 8
Please read these instructions carefully and retain them
for future reference to ensure that the table is used
correctly. For your own safety, please study each step of
this instruction manual. &tradition is not responsible
for any faults or damages caused by not following these
instructions correctly.
SAFETY PRECAUTIONS
- Dispose of plastic bag from packaging and do not allow
children to play with it.
- The table is only intended for interior use.
- Handle table tops with care in order not to scratch surfaces.
- Power tools can be used to assemble the table. Be careful
not to overtighten or damage screw or thread.
- Two or more persons are needed to turn table around once
assembled
- Spilled liquids of any kind should be removed immediately
from the table top as it may penetrate the surface treat-
ment and cause damage to it.
CLEANING INSTRUCTIONS
The Mezcla table is made from powder and plated coated
steel, solid wood and/or honed marble. Never use aggressive
or abrasive cleaning detergents for any parts of the table,
as this will cause irreparable damage.
Solid wood table top
For daily care, dust oiled furniture with a soft dry cloth.
Cleaning can be done using a soft cloth wrung in lukewarm
water following the wood grain and dried immediately with
E
F
GH I
B
A
C
D
J
2
a dry cloth following the wood grains. For more severe
cleaning a soap specically developed for oiled wood can
be used. Follow the instructions on the packaging of the
cleaning product. To maintain the look and silky feeling of
oiled wood, regular re-oiling is recommended. Re-oiling
should be done when the wood starts to appear dry or faded.
Usually, reoiling four times every year is sufcient.
Marble table top
The marble plate is made from natural marble and will
therefore have variations in structure and colour. This should
not be considered a defect nor a valid reason for claims. The
marble is treated with sealer, but it is strongly recommended
to use a trivet and never place glasses or cups with liquids
directly on to the marble. Spilled liquids will leave perma-
nent stains due to the natural sensitivity of marble.
For daily cleaning of the marble top it is recommended to
use a cleaning agent specically developed for stone or
marble. It is also highly recommended to do a re-sealing of
the marble every second month, using an appropriate sealer
developed specically for stone or marble.
Metal base
It is recommended only to use a soft dry cloth to clean
plated and powder coated surfaces but in case more severe
cleaning is necessary, a soft cloth wrung in lukewarm water
can be carefully applied. Always dry immediately after
cleaning with a soft dry cloth. Avoid using abrasive cleaning
agents or aggressive cleaning detergents on lated or powder
coated surfaces as this may permanently damage the surface.
3

STEP 3
Place the base (A) on the column, align the holes with the
corresponding holes in the column. Place the large counter
sunk bolts (F) in the appointed holes and fasten clockwise
with the large Allen key.
STEP 1
Place the column (C) on the oor. Place the top support
(B) on the column, align the holes with the correspond-
ing holes in the column. Place the large bolts (E) in the
appointed holes and fasten clockwise with the large Allen
key (H).
STEP 2
Turn the top support upside down on a soft, at surface.
STEP 4
Place the self-adhesive felt pads (J) on the bottom of the
base, with equal spacing and 1 cm from the edge as
illustrated.
1cm
4 5

STEP 5
Turn the base upside down.
6
STEP 6
Place the table top (D) on top of the top support. Align the
holes with the corresponding holes in the table top. Place
the anged button head screws (G) in the appointed holes
and fasten clockwise with the small Allen key (I).
Turn the table around and place carefully on the oor.
7