Arconic 2024 Series User manual

Patent Pending
December 6, 2018
HK1077
Makers of Huck®, Marson®, Recoil®
Brand Fasteners, Tools & Accessories
Instruction Manual
2024 series
Pneudraulic Installation Tool
Declaration of Conformity
2
Safety Instructions
3

4-6
Principle of Operation
7
Preparation for Use
7
Operating Instructions
8
Maintenance
8
Disassembly Instructions
9-10
Assembly Instructions
11-12
Fill and Bleed
13
Measuring Tool Stroke
14
Components Drawings
15-17
Troubleshooting
18
Kits and Accessories
18

2
2024 series Pneudraulic Installation Tool (HK1077)

3
2024 series Pneudraulic Installation Tool (HK1077)
I. GENERAL SAFETY RULES:
1.Ahalfhourlonghands-ontrainingsessionwithqualiedpersonnelis
recommendedbeforeusingHuckequipment.
2.Huckequipmentmustbemaintainedinasafeworkingconditionatall
times.Toolsandhosesshouldbeinspectedatthebeginningofeach
shift/dayfordamageorwear.Anyrepairshouldbedonebyaqualied
repairmantrainedonHuckprocedures.
3.Formultiplehazards,readandunderstandthesafetyinstructionsbefore
installing,operating,repairing,maintaining,changingaccessorieson,
orworkingneartheassemblypowertool.Failuretodosocanresultin
serious bodily injury.
4.Onlyqualiedandtrainedoperatorsshouldinstall,adjustorusethe
assemblypowertool.
5.Donotmodifythisassemblypowertool.Thiscanreduceeectivenessof
safetymeasuresandincreaseoperatorrisk.
6.Donotdiscardsafetyinstructions;givethemtotheoperator.
7.Donotuseassemblypowertoolifithasbeendamaged.
8.Toolsshallbeinspectedperiodicallytoverifyallratingsandmarkings
required, and listed in the manual, are legibly marked on the tool. The
employer/operatorshallcontactthemanufacturertoobtainreplacement
markinglabelswhennecessary.Refertoassemblydrawingandpartslist
forreplacement.
9. Tool is only to be used as stated in this manual. Any other use is
prohibited.
10.ReadMSDSSpecicationsbeforeservicingthetool.MSDS
specicationsareavailablefromtheproductmanufactureroryourHuck
representative.
11.OnlygenuineHuckpartsshallbeusedforreplacementsorspares.Use
ofanyotherpartscanresultintoolingdamageorpersonalinjury.
12.Neverremoveanysafetyguardsorpintaildeectors.
13.Neverinstallafastenerinfreeair.Personalinjuryfromfastenerejecting
may occur.
14.Whereapplicable,alwaysclearspentpintailoutofnoseassembly
before installing the next fastener.
15.Checkclearancebetweentriggerandworkpiecetoensurethereisno
pinchpointwhentoolisactivated.Remotetriggersareavailablefor
hydraulictoolingifpinchpointisunavoidable.
16.Donotabusetoolbydroppingorusingitasahammer.Neveruse
hydraulicorairlinesasahandleortobendorprythetool.Reasonable
careofinstallationtoolsbyoperatorsisanimportantfactorin
maintainingtooleciency,eliminatingdowntime,andpreventingan
accidentwhichmaycauseseverepersonalinjury.
17.Neverplacehandsbetweennoseassemblyandworkpiece.Keephands
clear from front of tool.
18.Toolswithejectorrodsshouldneverbecycledwithoutnoseassembly
installed.
19.Whentwopiecelockboltsarebeingusedalwaysmakesurethecollar
orientationiscorrect.Seefastenerdatasheetforcorrectpositioning.
II. PROJECTILE HAZARDS:
1.Riskofwhippingcompressedairhoseiftoolispneudraulicorpneumatic.
2.Disconnecttheassemblypowertoolfromenergysourcewhenchanging
inserted tools or accessories.
3.Beawarethatfailureoftheworkpiece,accessories,ortheinsertedtool
itselfcangeneratehighvelocityprojectiles.
4.Alwayswearimpactresistanteyeprotectionduringtooloperation.The
gradeofprotectionrequiredshouldbeassessedforeachuse.
5. The risk of others should also be assessed at this time.
6.Ensurethattheworkpieceissecurelyxed.
7.Checkthatthemeansofprotectionfromejectionoffastenerorpintailis
inplaceandoperative.
8.Thereispossibilityofforcibleejectionofpintailsorspentmandrelsfrom
front of tool.
III. OPERATING HAZARDS:
1.Useoftoolcanexposetheoperator’shandstohazardsincluding:
crushing,impacts,cuts,abrasionsandheat.Wearsuitableglovesto
protecthands.
2.Operatorsandmaintenancepersonnelshallbephysicallyabletohandle
thebulk,weightandpowerofthetool.
3. Hold the tool correctly and be ready to counteract normal or sudden
movementswithbothhandsavailable.
4.Maintainabalancedbodypositionandsecurefooting.
5.Releasetriggerorstopstartdeviceincaseofinterruptionofenergy
supply.
6.Useonlyuidsandlubricantsrecommendedbythemanufacturer.
7.Avoidunsuitablepostures,asitislikelyforthesenottoallow
counteractingofnormalorunexpectedtoolmovement.
8.Iftheassemblypowertoolisxedtoasuspensiondevice,makesure
thatxationissecure.
9.Bewareoftheriskofcrushingorpinchingifnoseequipmentisnottted.
IV. REPETITIVE MOTION HAZARDS:
1.Whenusingassemblypowertool,theoperatorcanexperience
discomfortinthehands,arms,shoulders,neckorotherpartsofthe
body.
2.Whenusingtool,theoperatorshouldadoptacomfortableposture
whilemaintainingasecurefootingandavoidawkwardorobalanced
postures.
3.Theoperatorshouldchangepostureduringextendedtaskstohelpavoid
discomfort and fatigue.
4.Iftheoperatorexperiencessymptomssuchaspersistentorrecurring
discomfort,pain,throbbing,aching,tingling,numbness,burning
sensationsorstiness,thesewarningsshouldnotbeignored.The
operatorshouldtelltheemployerandconsultaqualiedhealth
professional.
V. ACCESSORIES HAZARDS:
1.Disconnecttoolfromenergysupplybeforechanginginsertedtoolor
accessory.
2.Useonlysizesandtypesofaccessoriesandconsumablesthatare
recommended.Donotuseothertypesorsizesofaccessoriesor
consumables.
VI. WORKPLACE HAZARDS:
1.Beawareofslipperysurfacescausedbyuseofthetoolandoftrip
hazardscausedbytheairlineorhydraulichose.
2. Proceed with caution while in unfamiliar surroundings; there could be
hiddenhazardssuchaselectricityorotherutilitylines.
3.Theassemblypowertoolisnotintendedforuseinpotentiallyexplosive
environments.
4.Toolisnotinsulatedagainstcontactwithelectricalpower.
5.Ensuretherearenoelectricalcables,gaspipes,etc.,whichcancausea
hazardifdamagedbyuseofthetool.
VII. NOISE HAZARDS:
1.Exposuretohighnoiselevelscancausepermanent,disablinghearing
lossandotherproblemssuchastinnitus,thereforeriskassessmentand
theimplementationofpropercontrolsisessential.
2.Appropriatecontrolstoreducetheriskmayincludeactionssuchas
dampingmaterialstopreventworkpiecefrom‘ringing’.
3.Usehearingprotectioninaccordancewithemployer’sinstructionsandas
requiredbyoccupationalhealthandsafetyregulations.
4.Operateandmaintaintoolasrecommendedintheinstructionhandbook
topreventanunnecessaryincreaseinthenoiselevel.
5.Select,maintainandreplacetheconsumable/insertedtoolas
recommendedtopreventanunnecessaryincreaseinnoise.
6.Ifthepowertoolhasasilencer,alwaysensurethatitisinplaceandin
goodworkingorderwhenthetoolisbeingoperated.
VIII. VIBRATION HAZARDS:
1.Exposuretovibrationcancausedisablingdamagetothenervesand
bloodsupplytothehandsandarms.
2.Wearwarmclothingwhenworkingincoldconditionsandkeephands
warm and dry.
3.Ifnumbness,tingling,painorwhiteningoftheskininthengersor
hands,stopusingthetool,tellyouremployerandconsultaphysician.
4.Supporttheweightofthetoolinastand,tensionerorbalancerinorder
tohavealightergriponthetool.
IX. PNEUMATIC / PNEUDRAULIC TOOL SAFETY INSTRUCTIONS:
1.Airunderpressurecancausesevereinjury.
2.Alwaysshutoairsupply,drainhoseofairpressureanddisconnecttool
fromairsupplywhennotinuse,beforechangingaccessoriesorwhen
makingrepairs.
3.Neverdirectairatyourselforanyoneelse.
4.Whippinghosescancausesevereinjury,alwayscheckfordamagedor
loosehosesandttings.
5. Cold air should be directed away from hands.
6.Wheneveruniversaltwistcouplings(clawcouplings)areused,lockpins
shallbeinstalledandwhip-checksafetycablesshallbeusedtosafeguard
againstpossiblehosetohoseorhosetotoolconnectionfailure.
7.Donotexceedmaximumairpressurestatedontool.
8.Nevercarryanairtoolbythehose.
Safety Instructions
GLOSSARYOFTERMSANDSYMBOLS:
 - Productcomplieswithrequirementssetforthby
therelevantEuropeandirectives.
 - Readmanualpriortousingthisequipment.
 - Eyeprotectionisrequiredwhileusingthis
equipment.
 - Hearingprotectionisrequiredwhileusingthis
equipment.
Notes:areremindersofrequiredprocedures.
Bold, Italic type, and underline:emphasizeaspecic
instruction.
WARNINGS: Must be understood to avoid
severe personal injury.
CAUTIONS: Show conditions that will damage
equipment or structure.

4
2024 series Pneudraulic Installation Tool (HK1077)
Specifications
Stroke: 0.850in(2.16 cm)
Weight: 5.5lbs(2.5 kg)
MAX air PRESSURE:90psi(6.2 bar)
Max Flow Rate: 8.5 scfm(241 l/min)
Power Source:90psi(6.2 bar)maximumshopair
Max Operating Temp:125°F(51.7° C)
Pull Capacity: 3993lbs@90psi(17.76 kN @ 6.2 bar) 
3549lbs@80psi(15.79 kN @ 5.5 bar)
Hose Kits:UseonlygenuineHuckHoseKitsrated@
10,000psi(689.5 bar)workingpressure.
Hydraulic Fluid:HydraulicuidshallmeetDEXRON®
III,DEXRONVI,MERCON®,AllisonC-4orequivalent
AutomaticTransmissionFluid(ATF)specications.Fire-
resistantuidmaybeusedifitisanester-baseduid
such as Quintolubric®HFDorequivalent.Water-based
uidshallNOTbeusedasseriousdamagetoequipment
will occur.











































Models 2024 & 2024L Models 2024V & 2024LV
Inches
(cm)
Inches
(cm)
Where the following trade names are used in this manual, please note:
DEXRON is a registered trademark of General Motors Corporation.
GLYD Ring is a registered trademark of Trelleborg Sealing Solutions Germany GmbH
Loctite is a registered trademark of Henkel Corporation, U.S.A.
LUBRIPLATE is a registered trademark of Fiske Brothers Rening Co.
MERCON is a registered trademark of Ford Motor Corp.
MOLYKOTE is a registered trademark of Dow Corning Corporation
Never-Seez is a registered trademark of Bostik, Inc.
Quintolubric is a registered trademark of Quaker Chemical Corp.
Slic-tite is a registered trademark of LA-CO Industries, Inc.
Spirolox is a registered trademark of Smalley Steel Ring Company
Teon is a registered trademark of Chemours Company FC.
Threadmate is a registered trademark of Parker Intangibles LLC.
TRUARC is a trademark of TRUARC Co. LLC.
Vibra-Tite is a registered trademark of ND Industries, Inc. USA.

5
2024 series Pneudraulic Installation Tool (HK1077)



 











PULL STROKE
Whentoolisconnectedtotheairsupply,theair
pressureholdsthethrottlevalveintheup(RETURN)
position;airpressureisdirectedtothetopoftheair
piston,keepingitdown.Whenthetriggerispressed,
thethrottlevalvemovesdowntothePULLposition,
andpressurizedairisdirectedtothebottomoftheair
piston,causingittomoveupward(seeabove).Theair
abovetheairpistonisexhaustedanddirectedthrough
thecenterofthethrottlevalveandoutthebottomof
thetool(throughthemuer).
Asthehydraulicpistonrodmovesupward,acolumnof
pressurizeduidisforcedintohead,whichmovesthe
pullpistonrearward.Theattachednoseassemblymoves
withthepullpistontostartfastenerinstallation.
RETURN STROKE
Whenfastenerinstallationiscompleted,thetriggeris
released.Airpressure,withtheassistanceofaspring,
sendsthethrottlevalvetotheup(RETURN)position.
Pressurizedairisre-directedtothetopoftheairpiston
(seeabove),causingitandthehydraulicpistonrodto
movedownward.
Theairfrombelowthepistonisexhaustedthroughthe
bottomofthetool.Thepistonandhydraulicpistonrod
movedownward,hydraulicpressureisreversed,and
thepullpistonisreturnedforward.Thedampervalve
impedesoilowatpinbreakhelpingprevent“ToolKick”.
Principle of Operation
Figure 1bFigure 1a

6
2024 series Pneudraulic Installation Tool (HK1077)
Preparation for Use
WARNINGS:


forcibly from rear of tool. Unshielded eyes, especially, may be

pintails. If there is any chance of a projectile-like ejection, always
point rear of tool in a safe direction, or be sure there is some
structure that will stop ejecting pintails.
To avoid pinch points, be sure there is adequate clearance for tool
and operator’s hands before proceeding. Tool moving toward

clearance is limited.
The 2024seriesoftoolsshipwithaplugintheair
inletconnector.Theconnectorhas1/4”-18femalepipe
threadstoaccepttheair-hosetting.Huckrecommends
quick-disconnectttingsanda1/4”inside-diameter
airhose.Theairsupplyshouldhavealter-regulator-
lubricatorunitandaccessto90psi(6.2 bar),capableofa
owrateof8.5CFM(241 l/m).NOTE:Quick-disconnect
ttings and air hoses are not available for purchase
from Huck International, Inc. Huck includes an air
hose (P/N 115436) to facilitate immediate tool use.
1. Removetheshippingplugfromairinletconnector
andaddafewdropsofanapprovedhydraulicuid.
2. Screwthequick-disconnectttingintotheairinlet
connector.
3. Set the airpressureontheregulatorto90psi
(6.2 bar), and connect the air hose to the air inlet
connector and the tool.
4. Press and release the trigger a few times to cycle the
tool.
5. Disconnecttheairhosefromthetool,andremove
theretainingnut.Selectthepropernoseassembly
for the fastener being installed.
6. Screwthecolletassembly(includingthelockcollar
andshimifapplicable)ontothespindleandtighten
with a wrench.
7. Slidetheanviloverthecolletassemblyandintothe
counterbore.Slidetheretainingnutovertheanvil,
and screw the nut onto the head.
8. Connect the air hose to the tool and install fasteners
inatestplateofproperthicknesswithpropersize
holes.Inspectthefasteners.
Ifthefastenersdonotpassinspection,consultthe
Troubleshootingsectiontoinvestigatepossiblecauses.
NOTE: On older nose assemblies with lock collars, use
Loctite®243™ on collet threads, because the 2024
pull piston does not have staking holes. Refer to
the nose assembly drawings that shipped with nose
assemblies.
CAUTION: Do not use TEFLON®tape on pipe threads. Tape can

Threadmate®is available in a 4oz. tube from Huck (P/N 508517).

7
2024 series Pneudraulic Installation Tool (HK1077)
Operating Instructions
Read all of these instructions in order to ensure the safe operation of this equipment.
This section details installing MAGNA-GRIP®and Huck
BlindFasteners.ReviewallCAUTIONsandWARNINGs
priortoinstallingthesefasteners.Ifthetoolmalfunctions,
consult the Troubleshootingsectionbeforeattempting
anyrepairs.NOTE:Reasonable care of tools by
operators is an important factor in maintaining
eciency and reducing downtime.
To install a MAGNA-GRIP Fastener:
1. Placeapinintheworkpieceandplacethecollarover
thepin.
NOTE:If the collar has one tapered end, that end
must be out toward tool; not next to the sheet.
2. Holdthepinin the hole andpushthenoseassembly
ontothepinprotrudingthroughthecollaruntilthe
noseanviltouchesthecollar.
3. Press and hold the trigger until the collar is swaged
andthepintailbreaks.
4. Releasethetrigger;thetoolwillperformitsRETURN
stroke.
Thepressureisre-directed;thepistonmovesforward;and
thetoolispushedothefastenerandreadyforthenext
installation cycle.
To install a Huck Blind Fastener:
1. Placeafastenerintheworkpieceorintheendofthe
nose assembly.
NOTE:The tool or nose assembly must be
held against, and at a right angle (90°) to, the
workpiece.
2. Press and hold the trigger until the fastener is
installedandthepintailbreaks.
3. Releasethetrigger;thetoolwillperformitsRETURN
stroke.
Thepressureisre-directed;thepistonmovesforward;and
thetoolispushedothefastenerandreadyforthenext
installation cycle.
For complete safety information, see page 4.
CAUTION:
Make sure the tool is properly re-assembled before use.

stroke.
Remove excess gap from between the sheets to permit proper fastener installation and prevent jaw
damage. ALL jaw teeth must engage the pintail to avoid damaging the teeth.
WARNINGS:
Inspect tools for damage and wear before using. Do not use if damaged or worn; serious personal
injury may occur.
Pulling a pin (fastener) without a collar, or with collar chamfer against workpiece, may result in the

Serious personal injury may occur 



Wear approved eye and hearing protection.
Ensure adequate clearance for operator’s hands before installing fasteners.

personnel.
Do not pull on a pin without placing a fastener in a workpiece. Make sure that the collar chamfer is

which could cause serious injury.

8
2024 series Pneudraulic Installation Tool (HK1077)
GENERAL
Theoperatingeciencyofyourtoolisdirectlyrelated
totheperformanceoftheentiresystem.Regular
inspectionandtheimmediatecorrectionofminor
problemswillkeepthetooloperatingeciently,
andpreventdowntime.Ascheduleof“preventive”
maintenance of the tool, nose assembly, hoses, trigger
and control cord, and POWERIG®willensureyourtool’s
properoperationandextenditslife.
NOTE:Huck tools should be serviced only by
personnel who are thoroughly familiar with its
operation.
- Servicethetoolinaclean,well-lightedarea.Take
specialcaretopreventcontaminationofpneumatic
and hydraulic systems.
- Haveavailableallnecessaryhandtools(standardand
special),abrass drift and wood block, and a soft-jaw
vise. See .
- Carefullyhandleallparts.Beforereassembly,examine
them for damage and wear.
- Disassembleandassembletoolcomponentsina
straightline.DoNOTbend,cock,twist,orapplyundue
force.
- HavetheappropriateSpare Parts Service Kit
(2024KIT or 2024LVKIT)availablewhenservicing
thetool;itincludesimportantperishableparts.Other
components,asexperiencedictates,shouldalsobe
available.See.
- ApplyLoctite®243 Threadlocker (Huck P/N 508567)
toglandthreads.ApplyLoctite®271-05 (Huck P/N
503657)tonutsandlocknut(P/N505420);torqueto
25–30 ft.-lbs.
- Smear LUBRIPLATE®130-AA(Huck P/N 502723)or
SUPER-O-LUBE®(HuckP/N505476)onrings and
matingpartstoeaseassembly.
- ApplyThreadmate®(HuckP/N508517)topipe
threadsandquick-disconnectttings.
Forsupplementaryinformation,see,and
the  and proceduresinthismanual.
DAILY
- Huckrecommendsusingalter-regulator-lubricator
unit.Ifoneisnotbeingused,uncoupletheair
disconnectsandaddafewdropsofhydraulicuidor
a light-weight oil to the air inlet of the tool.
NOTE:If the tool is in continuous use, add a few
drops of uid every 2–3 hours.
- Before connecting an air hose to the tool, clear the air
lines of dirt and water.
- Checkallhosesandcouplingsfordamageandair
leaks;tightenorreplaceifnecessary.
- Check the tool and nose assembly for damage and
airorhydraulicleaks;tighten,repair,orreplaceif
necessary.
- Inspectthetool,hoses,andPOWERIGduring
operationtodetectabnormalheating,leaks,or
vibration.
- Clean nose assemblies inmineralspiritstoclearjaws
andrinsemetalchipsanddirt.Foramorethorough
cleaning,disassemblethenoseassembly.Usea
pointed“pick”toremoveimbeddedparticlesfromthe
pullgroovesofthejaws.
CleanallpartsofanyassemblywithUNITIZEDTM Jaws
inmineralspiritsorisopropylalcoholonly;donotlet
jawscomeincontactwithothersolvents.Donotlet
jaws soak; dry them immediately after cleaning. Huck
recommendsdryingotherpartsbeforere-assembling.
WEEKLY
- Disassemble, clean, and re-assemble nose assembly in
accordancewithapplicableinstructions.
- Checkthetoolandallconnectingpartsfordamage
and uid/airleaks;tightenorreplaceifnecessary.
Maintenance
CAUTION: Replace all seals, wipers, and
rings when the tool is disassembled for any
reason, and at regular intervals, depending
on severity and duration of use.
CAUTION: Do not use TEFLON®tape on
pipe threads. Tape can shred and break free

Threadmate®is available in a 4oz. tube
from Huck (P/N 508517).
CAUTION: Damaged jaw teeth, or debris
packed between teeth, will result in
fastener not being installed or being
improperly installed.

9
2024 series Pneudraulic Installation Tool (HK1077)
Disassembly
GENERAL
Thisprocedureisforthecompletedisassemblyofthe
tool.Disassembleonlythosecomponentsnecessaryto
replacedamagedO-rings,Quad-rings,Back-uprings,
andwornordamagedcomponents.Forcomponent
identication,seeFigures2–5,10,and 14.
1. Disconnect the tool from the air source.
2. Unscrewtheretainingnutandremovethenose
assembly.(FollowtheinstructionsontheNose
Assembly Data Sheet.)
3. Unscrewthebleedplugfromtopofthehead/
handle.Turnoverthetool(Figures10&14)and
draintheuidintoacontainer.(Thetoolcanbe
cycledtoclearmorecompletely.)Discardtheuid.
4. Models 2024 & 2024L:Pullthepintaildeectoro
theendcap.
Models 2024V & 2024LV:See
 and Figures 5, 6, &
10.
5. Removethrottlearmpivotscrewandleverguard,
and lift out throttle arm. Disconnect the ball end of
the cable assembly from it.
6. Securethetoolupside-downinasoft-jawvise;use
a1/8”hexkeytoremovebutton-headscrewsfrom
themuerendcap.(Figure2)Removeendcapand
gasket,andremovemuerfromtheendcap,and
springfromthethrottlevalve.(Figure14)
7. Tapdownthecylinderheadwithasoftmallet(to
takepressureothering),andremovetheretaining
ring.(Figure2)
8. Screw the button-head screws into cylinder head;
(Figure 2)carefullypryonscrewstoremovehead.
RemovetheO-ring.
9. Pullonlocknutwithvise-gripstoremovetheair
pistonfromcylinder.RemovethepistonQuad-ring.
10. Removebumperfromtheglandassembly.Unscrew
theglandassemblywitha1-3/8”socketwrenchand
extension.
11. Removeretainingringfromgland,andthenpull
outspacerandPolyseal.(Figure2)RemoveO-rings,
Quad-ring,andBack-upring.Liftcylinderassembly
fromthehead/handle.(Figure2)
12. Turnoverthetoolanddraintheuidintoa
container;discardtheuid.
13. Removethrottlevalvefromaircylinder,andremove
theO-rings.(Figure14)
HEAD/HANDLE
Thisprocedureisapplicabletomodels2024 and 2024L.
Forcomponentidentication,seeFigures3,4, and 14.
For models 2024V and 2024LV, see 
.
1. Unscrewendcap;removespring,spacer,andwiper
seal.(Figure3)
2. Thread the Polyseal Insertion Tool into the rear of
the head/handle. NOTE:See Figure 3 for tool-
specic part numbers.




















Figure 2
CAUTION: Always use a soft-jaw vise to
avoid damaging the tool.
CAUTION: Take care to not scratch the
piston, rod, or cylinder when removing.
WARNING: Disconnect the air hose
from the tool before performing any
maintenance. Serious personal injury could
result if the air hose is connected.

10
2024 series Pneudraulic Installation Tool (HK1077)
3. Slidethespacerontothepiston.ThreadthePiston
AssemblyToolontothepiston.(Figure3)
4.
Pushthepistonandfrontglandassembliesoutthe
back of the head/handle; allow clearance, with stand-
o,asthepistonleavesthetool.(Figures 4 & 7)
5. Un-threadthePistonAssemblyToolandremove
spacerfromthepiston.Re-threadthePiston
AssemblyToolontothepiston,thenslidethefront
glandassemblyothepiston.(Figures 4 & 7)
6. RemovethePistonAssemblyToolfromthepiston,
andremovethePolysealInsertionToolfromtherear
of the head/handle.
7. Removeretainingring,washer,andPolysealfromthe
piston.
NOTE:Inspect the hydraulic piston for wear,
scoring, and damage; replace if necessary.
8. Unscrewtheadapter.(Figure14)Inspectallsealsand
parts.
9. Iftriggercableassemblyisdamaged,removeitby
drivingoutpinwithapunch.Removedowelpinto
disconnect the cable from the the trigger.
PINTAIL BOTTLE/VACUUM SYSTEM DISASSEMBLY
Thisprocedureisapplicabletomodels2024V and
2024LV only; it should be used in conjunction with the
previoussections, and . For
componentidentication,seeFigures5, 6, and 15.
1. Reachthroughthewindowofpintailbottleand
removeretainingringandwasher.(Figure5)
2. Removepintailbottle, and then disconnect the tube
fromthetubingconnector.(Figure15)
3. RemovetheadapterandtheTubing & Slide
Assembly.Thenremovetheendcapandspring.
(Figure6)
4. RemovethespacerandO-ringfromthespringside
oftheendcap.Removeretainingring,wiperhousing,
wiperseal,washer,andO-ringfromthebottle side of
theendcap.
5. RemoveO-ringsfrominsidetheadapterand Tubing
and Slide Assembly.(Figure 15)
Disassembly (continued)
Piston Assembly Tool
123111-2 (2024)
123111-4 (2024L)
123112-4 (2024LV, 2024V)
Spacer
123112-2 (2024)
123112-3 (2024L, 2024LV, 2024V)
123761 Adapter
Handle Assembly
127748 (2024, 2024L)
128132 (2024LV, 2024V)
Polyseal Inseron Tool
121694-2024 (all models)
PRESS
SUPPORT / STAND-OFF
Figure 3





Figure 4
501007 Retaining Ring
and 506628 Washer
125862
End Cap
128044 Tubing & Slide Assembly
123784 Adapter
123772 Pintail Bole
Figure 5
500780
O-ring
508187
Spring
125866
Spacer
125862
End Cap
500809
O-ring
125865
Washer
507351
Wiper
Seal
502317
Retaining
Ring
125864
Wiper Housing
Figure 6

11
2024 series Pneudraulic Installation Tool (HK1077)
Assembly
HEAD/HANDLE
Thisprocedureisfortheassemblyofthehead/handle
of models 2024 & 2024L.Forcomponentidentication,
see Figures 7, 8, 14, and 15.
For models 2024V and 2024LV, see 
.
Prior to re-assembling the tool:
• Cleancomponentswithmineralspiritsorasimilar
solvent.Inspectforwear/damageandreplaceas
necessary.
• UsetheO-rings,Quad-rings,andBack-uprings from
HuckServicePartsKits(P/N2024KIT or 2024VKIT).
When assembling the tool, take care not to damage
O-rings,Quad-rings,Back-uprings.
Smear LUBRIPLATE®130-AA(Huck P/N 502723)or
SUPER-O-LUBE®(HuckP/N505476)onrings and
matingpartstoeaseassembly.
To re-assemble the tool:
1. Ifremoved,positioncableassemblyintriggerslot
andslidedowelpinthroughtheholesintrigger-
and-cable assembly. Position the assembled trigger
inthehandleanddrivepinthroughtheholesinthe
handleandtrigger.(Figure14)
2. Screwnoseadapterintohead;tighten.
3. ThreadthePolysealInsertionTool(P/N121694-
2024)intothehead.(Figure8)
4. Assemblepiston,Polyseal,andretainingring.(Note
the orientation of the Polyseal in Figures 4 & 7.)
5. Assemblefrontgland,O-ring,Back-upring,Polyseal,
andglandcap.(Note the orientation of the Polyseal
in Figures 4 & 7.)
6. ThreadthePistonAssemblyTool(see P/Ns in gures)
ontopiston.Slidethecompleteglandassemblyand
wipersealontopiston.
7. Useapresstogentlyinstalltheassembled
componentsthroughtherearofthetool.(Figure8)
8. RemovethePistonAssemblyToolandthePolyseal
Insertion Tool.
9. Installrearwipersealintoendcap.(Figure14)
10. Slidespacerandspringintoendcap,andthen
threadtheendcapassemblyintotherearofthe
head.(Figure15)
NOTE:Models 2024V and 2024LV, see 
 and Figures 5, 6, and 10.
123761 Adapter
Handle Assembly
127748 (2024, 2024L)
128132 (2024LV, 2024V)
Polyseal Inseron Tool
121694-2024 (all models)
PRESS
SUPPORT / STAND-OFF
Figure 8
CAUTION: Always replace all seals, wipers
and rings of disassembled components;
these parts wear out over time.
Replacement minimizes problems.
Piston Assembly Tool
123111-2 (2024)
123111-4 (2024L)
123112-4 (2024LV, 2024V)
Piston Assembly
127743 (2024)
127744 (2024L)
127744-2 (2024V)
127744-1 (2024LV)
502827
Retaining Ring
127749
Washer
508188 Polyseal
(note orientaon)
505817
Wiper Seal
122432
Gland Cap
123757
Front Gland
500816
O-ring
501110
Back-up Ring
505818 Polyseal
(note orientaon)
Figure 7

12
2024 series Pneudraulic Installation Tool (HK1077)
Assembly (continued)
GENERAL
Forcomponentidentication,seeFigures2,7,and13.
1. Secure head/handleupside-downinasoft-jawvise.
(Figure2)Placetheinvertedcylinderassemblyon
thebaseofthehandle.(Thetimingpinmaintains
orientation.)
2. Assemble Main Gland Assembly with new seals.
(Note the orientation of the Polyseal in Figure 14.)
ApplyLoctite®243™to the threads of the gland.
Screwtheglandassemblyintothehandle/head.Use
a1-3/8”socketwrenchtotightenandtorqueto
36–66 ft.-lbs.
3. Pushbumperrmlyoverthegland.
NOTE:The side of the bumper with two slots
must face the bottom of the tool.
4. InstallO-ringontoairpiston.
5. CleanthepistonrodthreadsandapplyLoctite®
243™.Presstheassembledairpiston/rodintothe
cylinder just enough to allow installation of the
cylinder head.
6. InstallO-ringonthecylinderheadandthenpush
the cylinder head squarely into the cylinder, taking
care not to damage O-ring. Install the retaining ring;
alignthescrewholeswiththemuerendcap.
7. Positionmuerincenterofcylinderhead.(Figure2)
Positiongasketonthecylinder.(Note the orientation
of the Polyseal in Figure 7.)
8. Carefullypositionbottomplateonthecylinder.
NOTE:Make sure the muer is properly
positioned in the recess of the bottom plate.
(Figures 2 & 14)
9. Securethebottomplatewiththreebutton-head
screwsusinga1/8”hexkey.(Figure2)
10. InstallO-ringsonthrottlevalve.(Figure14)
11. Placethetooluprightonalevelsurface.Drop
springintothethrottlevalveboreincylinder,and
pushthethrottlevalveintothecylinder.
12. Place the ball end of throttle cable into the end of
throttle arm, then slide the throttle arm into the slot
onthecylinder.(Figure14)
13. Snapleverguardinplace,andinstallpivotscrewin
the cylinder to retain throttle arm.
14. Models 2024 & 2024L:Pushpintaildeectoronto
endcap.
Models2024V&2024LV:see
 and Figures 5, 6, and 10.
Thetoolisnowassembledandmustbelledwith
hydraulic uidpriortouse.Seethe
section. NOTE: Install the bleed plug and O-ring
assembly after that process.
PINTAIL BOTTLE/VACUUM SYSTEM ASSEMBLY
Thisprocedureisapplicabletomodels2024V and
2024LV only; it should be used in conjunction with
theprevioussections, and . For
componentidentication,seeFigures 5, 6, and 15.
1. AssembleadapterandTubing & Slide Assembly and
new O-rings.
2. Fromthebottlesideofendcap,installO-ring,
washer,wiperseal,wiperhousing,andretainingring
as shown in Figure 6.
3. From the toolsideoftheendcap,installO-ring,
spacer,andspring.(Figure6)Screwtheentire
assembly into the head; tighten.
4. Assemble the Tubing & Slide Assembly and O-rings;
slidethecompleteassemblyontoendcap,andpush
thetubeintoconnector.(Figure15)
5. Positionadapterandpintailbottleonendcap.
(Figures5&15)
6. Reachthroughthewindowofthepintailbottleand
install the washer and retaining ring as shown in
Figure 5.
CAUTION: Always use a soft-jaw vise to
avoid damaging the tool.

13
2024 series Pneudraulic Installation Tool (HK1077)
Fill and Bleed
Thissectiondocumentsthe“bleed-&-ll”procedure.For
componentidentication,see Figures 9–11.
REQUIRED EQUIPMENT
• DEXRON®IIIorequivalentATF(See for
moreinformation.)
• Shopair-linewith90psi(6.2 bar)max.
• Air regulator
• FillBottleAssy(P/N120337,suppliedwithtool)
• Largeat-bladescrewdriver
• StallNut(P/N124090 or 125340,optional)
• Nose assembly
• Fasteners(optional)
PREPARATION
• Installairregulatorintheair-lineandsetthepressure
to20–40psi(1.4–2.8 bar).
• Addanapprovedhydraulicuidtothellpointofthe
llbottle.

1. Laythetoolonitssidewiththellportfacingup
andremovebleedplugfromthellport.
2. Connectthetooltoshop
air-line.Ifuidispresent,
holdthetooloverasuitablecontainerwithllport
facingintocontainer.Cyclethetoolseveraltimesto
drainolduid,air,andfoam.(Figure10)
3. Screwthellbottleintothellport.(Figure11)
4. Standthetooluprightonabench.Triggerthetool
slowly(20–30cycles),andbendthellbottleata
right-angle(90°)tothetool.(Figure11)Airbubbles
willaccumulateattopofthebottle.
5. Whenairbubblesstopaccumulatingattopofthe
bottle,stopcyclingthetool.Whenthetriggeris
released,thepullpistonreturnstotheidleposition
(full-forward).
6. Disconnect the tool from the air-line. Lay the tool
onitssideandremovethellbottle.Topothe
uidinthellport,andinstallandtightenthebleed
plug.
7. Connect the air-line to the tool and measure the
stroke as described in .
If the stroke is less than the length specied in
,removethebleedplugandadduid.
Re-insertthebleedplugandre-measurethestroke.
8. Increasetheairpressuretothethemaximumlisted
in . Install two fasteners to check
the function and installation in a single stroke, or
cycle the tool with a stall nut fully threaded onto
thepistontoloadupthetool.Measurethestroke
again.Ifnecessary,removetheplugandadduid.
Re-inserttheplug,andcycleandmeasureagain.
Repeatthisprocessuntilthestrokemeetsthe
recommended minimal length.
WARNING: Avoid contact with hydraulic

in accordance with local regulations. See

120336
Fill Bole
Fill Point
120004 Cap
120337 Fill Bole Assy
Figure 9
WARNING: Air pressure must be set at
20–40 psi (1.4–2.8 bar) to prevent possible
injury from high-pressure spray.

must be in place before cycling the tool.
CONTAINER
(Discard fluid)
Figure 10
CAUTION



that is recommended in .
Figure 11

14
2024 series Pneudraulic Installation Tool (HK1077)
Measuring Tool Stroke
NOTE:Remove the Nose Assembly from the tool for both of the following procedures.
2024L & 202LV
1. Cyclethepistonallthewayforward
and measure X.
2. Cycleandholdthepistonbackand
measure Y.
Stroke = X-Y
If the stroke is less than 0.850 in (2.16 cm),
follow the steps at the end of the 
procedure.
Figure 13
2024 &2024V
1. Cyclethepistonallthewayforwardand
measure X.
2. Cycleandholdthepistonbackand
measure Y.
Stroke = Y-X
If the stroke is less than 0.850 in (2.16 cm), follow the
steps at the end of the  procedure.
Figure 12

15
2024 series Pneudraulic Installation Tool (HK1077)
125742 Main Gland Assembly
125740 Gland
Housing
500787 O-ring
507447 Polyseal
(note orientation)
125741 Spacer
506876
Retaining Ring
500785 O-ring
501091
Back-up Ring
501075
Quad Ring
Tighten and torque to 36–66 ft.-lbs.
Bumper
116408
Cylinder Assembly
125733 **
Timing Pin
Muffler
Piston Rod
125743
500903 O-ring
Air Piston
130729
Retaining Ring
507445
Gasket
126941-4
Screw (3)
504127 Bottom Plate128792 115554-1 Locknut 505420
Washer
506493
Cylinder
Head
125747
O-ring
500871
Pivot Screw
125118
SECTION A-A
125742
Gland Assembly
(see below)
NOTE:
These stickers are at the base of Cylinder
Assembly 125733. They must be purchased
and placed as shown if they become
damaged, lost, or unreadable, or if the
Cylinder Assembly is replaced.
590350
CE Sticker
590351
Max. Pressure
and Flow Sticker
590347
HUCK Address
Sticker
HUCK 2024
125751
Throttle Arm
125562-1
Throttle Valve
507396
O-ring (2)
507396
O-ring
116272
Spring
CC
A
A
507167 Swivel Assembly
SECTION C-C
500778 O-ring
500779
O-ring (2)
502274
Retaining
Ring
507164
Swivel Assy
Tool Base (all models)
Figure 14

16
2024 series Pneudraulic Installation Tool (HK1077)
TOOL HEAD 2024 & 2024L
Top View
104293 Bleed
Plug Assembly
506576 Plug &
Gasket Assembly
126439 Guard
505438
O-ring
A
A
Polyseal
505818 *
Front
Gland
123757
Retaining Ring
502827
Washer127749
Polyseal508188 *
Spring508187
WARNING Scker
590240-1 **
End Cap127742
Spacer
507323
Wiper Seal
507351 *
Pintail Deflector
124210
Handle
Assembly
127748 **
Cable Assembly
116404-1
Stop
120588
* Note orientaon of Wipers and Polyseals.
** WARNING scker (590240-1) MUST be
purchased and placed as shown when it
becomes damaged, lost, or unreadable, or
if Handle Assembly (127748) is replaced.
Dowel Pin505496
Trigger Pin500621
Trigger124333-2
127743 Piston
(2024)
127744 Piston
(2024L)
Retaining Nut
111795
Adapter
123761
Wiper Seal
505817 *
Gland Cap
122432
Back-up Ring
501110
O-ring
500816
SECTION A-A
Head/Handle 2024 & 2024L
Figure 14a

17
2024 series Pneudraulic Installation Tool (HK1077)
507351
Wiper Seal
125862 End Cap 125866
Spacer
128044 Tubing
and Slide Assy
500780
O-ring
500809
O-ring
125865
Washer
125864
Wiper Housing
502317
Retaining Ring
501007
Retaining
Ring
506628
Washer
123784
Adapter
500790
O-ring (2)
123772 Pintail
Bole
Piston Assembly
127744-2 (2024V)
127744-1 (2024LV)
PARTIAL SECTION A-A
(Note orientaon.)
506675 Tubing
Connector
Head 2024V & 2024LV
Figure 15

18
2024 series Pneudraulic Installation Tool (HK1077)
Troubleshooting
Alwayscheckthesimplestpossiblecause(suchasalooseordisconnectedtriggerline)ofamalfunctionrst.Then
proceedlogically,eliminatingotherpossiblecausesuntilthecauseisdiscovered.Wherepossible,substituteknown
goodpartsforsuspecteddefectiveparts.Usethistroubleshootinginformationtoaidinlocatingandcorrecting
trouble.
1. Tool fails to operate when trigger is pressed.
a. Air-linenotconnectedorairpressuretoolow.
b. WornordamagedthrottlevalveO-rings.
c Brokenthrottlevalvecable.
2. Tool does not complete fastener installation and
break pintail.
a. Airpressuretoolow.
b. WornordamagedairpistonQuad-ring.
c. Toolislowonhydraulicuid. See the 
 section.
d. Air in hydraulic system. See .
3. Pintail stripped and/or swaged collar not ejected.
a. Check for broken or worn jaws in nose assembly.
See the Nose Assembly Data Sheet.
b Checkforwornanvil.SeetheappropriateNose
Assembly Data Sheet.
4. Hydraulic uid exhausts with air or leaks at base
of handle.
a. Wornordamagedglandassembly.Inspect
Polyseal and all rings. Replaceifnecessary.
5. Hydraulic uid leaks at rear of pull piston.
a. Worn or damaged hydraulicpistonPolyseal.
InspectPolyseal.Replaceifnecessary.
6. Hydraulic uid leaks at front of pull piston.
a. Wornordamagedpartinfrontgland.Inspect
Polysealandrings.Replaceifnecessary.
7. Pull piston will not return.
a. Throttlevalvestuck;lubricateO-rings.
b. Throttle arm, cable, or trigger binding.
8. Air leaks at air cylinder head.
a. Worn or damaged O-ring.Replaceifnecessary.
Kits & Accessories
KITS
Service Kits - 2024KIT (2024&2024L)
- 2024LVKIT (2024LV&2024V)
Conversion Kit(convert2024L to 2024LV)- 126190
- Tubing and Slide Assembly - 124245
- Pintail Collection Bottle - 123772
- End Cap Assembly - 125863
- Piston Assembly - 125738-3
Conversion Kit(convert2024 to 2024V)- 126432
- Tubing and Slide Assembly - 124245
- Pintail Collection Bottle - 123772
- Vacuum Attach Adapter - 123784
- End Cap Assembly - 125863
- Retaining Ring Ext - 501007
- Straight Connector - 506675
- Piston Assembly - 125738-2
- Flat Washer - 506628
Assembly Tool Kit - 123110-17 *
*The Model 2024LKitP/Nis123110-18.
- Polyseal Insertion Tool - 121694-2024
- Piston Assembly Tool - 123111-2 (2024)
- 123111-4 (2024L)
- 123112-4 (2024LV,2024V)
- Spacer - 123112-2 (2024)
- 123112-3 (2024V,L,&LV)
ACCESSORIES
Stall Nut
-2024&2024V -124090
-2024L&2024LV -125340
Fill Bottle Assy (Fig.9) - 120337
Damper Valve
Removal Tool - 123769
STANDARD TOOLS AVAILABLE FROM HUCK
-1/8”hexkey(P/N502294),useonbutton-headscrew
(P/N504127)
Huckhascreatedtool-specicSpare Parts Service Kitsthatcontainvariousperishableparts.Thetypesand
quantitiesofsparepartsthatshouldbeavailablevarywiththeapplicationandtoolsinuse.Havetheappropriatekit
accessiblewhenusingthistoolandwhenperformingmaintenanceonit.HuckAssembly Tool Kitshaveproduct-
specictoolsthatshouldbeusedwhendisassemblingandassemblingthetool.
HuckrecommendshavingthefollowingAccessoriesavailablewhenpreparing,using,andperformingmaintenance
on this tool.

19
2024 series Pneudraulic Installation Tool (HK1077)
Limited Warranties
Limited Lifetime Warranty on BobTail® Tools:
HuckInternational,Inc.warrantstotheoriginalpurchaser
that its BobTail® installation tools manufactured after
12/1/2016 shall be free from defects in materials and
workmanshipforitsuseful lifetime. This warranty does
notcoverspecialorder/non-standardproducts,orpart
failureduetonormalwear,toolabuseormisapplication,
orusernon-compliancewiththeservicerequirementsand
conditionsdetailedintheproductliterature.
Two Year Limited Warranty on Installation Tools:
Huck International, Inc. warrants that its installation tools
and Powerig®hydraulicpowersourcesmanufacturedafter
December 1, 2016 shall be free from defects in materials
andworkmanshipforaperiodoftwoyearsfromdateof
purchasebytheenduser.Thiswarrantydoesnotcover
specialorder/non-standardproducts,orpartfailuredue
tonormalwear,toolabuseormisapplication,orusernon-
compliancewiththeservicerequirementsandconditions
detailedintheproductliterature.
90 Day Limited Warranty on Nose Assemblies and
Accessories:
Huck International, Inc. warrants that its nose assemblies
and accessories shall be free from defects in materials
andworkmanshipforaperiodof90daysfromdateof
purchasebytheenduser.Thiswarrantydoesnotcover
specialclearancenoses,orspecialorder/non-standard
product,orpartfailureduetonormalwear,abuseor
misapplication,orusernon-compliancewiththeservice
requirementsandconditionsdetailedintheproduct
literature.
Useful lifetimeisdenedastheperiodoverwhichthe
productisexpectedtolastphysically,uptothepointwhen
replacementisrequiredduetoeithernormalin-service
wear,oraspartofacompleteoverhaul.Determinationis
madeonacase-bycasebasisuponreturnofpartstoHuck
International,Inc.forevaluation.
Tooling, Part(s) and Other Items not manufactured by
Huck:
HUCKmakesnowarrantywithrespecttothetooling,
part(s),orotheritemsmanufacturedbythirdparties.HUCK
expresslydisclaimsanywarrantyexpressedorimplied,as
tothecondition,design,operation,merchantability,or
tnessforuseofanytool,part(s),orotheritemsthereof
notmanufacturedbyHUCK.HUCKshallnotbeliablefor
any loss or damage, directly or indirectly, arising from the
useofsuchtooling,part(s),orotheritemsorbreachof
warranty or for any claim for incidental or consequential
damages.
Huck shall not be liable for any loss or damage resulting
fromdelaysornon-fulllmentofordersowingtostrikes,
res,accidents,transportationcompaniesorforanyreason
orreasonsbeyondthecontroloftheHuckoritssuppliers.
Huck Installation Equipment:
HuckInternational,Inc.reservestherighttomakechanges
inspecicationsanddesignandtodiscontinuemodels
without notice.
HuckInstallationEquipmentshouldbeservicedbytrained
servicetechniciansonly.
Alwaysgivetheserialnumberoftheequipmentwhen
correspondingororderingserviceparts.
CompleterepairfacilitiesaremaintainedbyHuck
International,Inc.Pleasecontactoneoftheoceslisted
below.
Eastern
OneCorporateDriveKingston,NewYork12401-0250
Telephone(845)331-7300FAX(845)334-7333
OutsideUSAandCanada
ContactyournearestHuckInternationallocation(see
reverse).
Inadditiontotheaboverepairfacilities,thereare
AuthorizedToolServiceCenters(ATSC’s)located
throughouttheUnitedStates.Theseservicecentersoer
repairservices,spareparts,ServicePartsKits,Service
ToolKitsandNoseAssemblies.PleasecontactyourHuck
RepresentativeorthenearestHuckInternationallocation
(seereverse)fortheATSCinyourarea.

Arconic Inc. (NYSE: ARNC) creates breakthrough products that
shapeindustries.Workinginclosepartnershipwithourcustomers,
we solve complex engineering challenges to transform the way
wey,drive,buildandpower.
Throughtheingenuityofourpeopleandcutting-edgeadvanced
manufacturing, we deliver these products at a quality and
eciencythatensurescustomersuccessandshareholdervalue.
CERTIFIED
MANAGEMENT
SYSTEM
ISO 9001-2015
ISO 14001-2015
© 2018 Huck International, Inc.
Arconic Fastening Systems
Kingston Operations
1 Corporate Drive, Kingston, NY 12401
Tel: [phone] • Fax: [phone]
www.afshuck.net/us
INDUSTRIAL NORTH AMERICA
Kingston Operations
1CorporateDrive
Kingston,NY12401
Tel:[phone]
Fax:[phone]
[email protected]
Tracy Operations (IDG)
1925NorthMacArthurDrive
Tracy, CA 95376
Tel:[phone]
Fax:[phone]
[email protected]
Waco Operations
PO Box 8117
8001ImperialDrive
Waco,TX76714-8117
Tel:[phone]
Fax:[phone]
[email protected]
INDUSTRIAL GLOBAL
Kolkata Operations
UnitNo.28,2ndFloor,
55/1, Chowringhee Road,
Kolkata700071,WestBengal,India
Tel:[phone]
Tel:[phone]
Fax[phone]
Melbourne Operations
1508 Centre Road
Clayton,Victoria
Australia 3168
Tel:[phone]
Fax:[phone]
[email protected]
São Paulo Operations
RodoviaAnhanguera,s/n,KM17
ParqueSãoDomingos-Complexo
Anhanguera-Galpão1SeçãoIII
(MóduloIII)Box11
CEP05112-000SãoPaulo–SPBrazil
Tel:[phone]
Suzhou Operations
58 Yinsheng Road,
SIPSuzhou,Jiangsu
215126 China
Tel:[phone]-8888
Telford Operations
UnitC,StaordPark7
Telford,Shropshire
England TF3 3BQ
Tel:[phone]
Fax:[phone]
[email protected]
Tokyo Operations(JapanandKorea)
1013HibiyaU-1Bldg.
Uchisaiwai-cho1-1-7
Chiyoda-ku, Tokyo
100-0011Japan
Tel:[phone]
Fax:[phone]
AEROSPACE NORTH AMERICA
Kingston Operations
1CorporateDrive
Kingston,NY12401
Tel:[phone]
Fax:[phone]
[email protected]
Simi Valley Operations
3990A Heritage Oak Court
SimiValley,CA93063
Tel:[phone]
Fax:[phone]
www.afs-simivalley.com
AEROSPACE GLOBAL
Aichach Operations
Robert-Bosch Str. 4
Aichach 86551
Germany
Tel:[phone]
[email protected]
Cergy Operations
15 Rue du Petit Albi
F-95611 Cergy Pontoise
France
Tel:[phone]
Fax:[phone]
Hong Kong Operations
27th Floor, 88 Hing Fat Street
Causeway Bay
HongKong,China
Tel:[phone]
Arconic Fastening Systems Tooling Support Locations
Huck provides technical assistance
regarding the use and application of
Huck fasteners and tooling. NOTICE: The
informationcontainedinthispublication
is only for general guidance with regard
topropertiesoftheproductsshownand/
orthemeansforselectingsuchproducts,
and is not intended to create any warranty,
express,implied,orstatutory;allwarrantiesarecontained
only in Huck’s written quotations, acknowledgments,
and/or purchase orders. It is recommended that the
user secure specic, up-to-date data and information
regardingeachapplicationand/oruseofsuchproducts.