Argos HOME New Pagnell 3 Dr 4 Drw Wardrobe... User manual

Assembly Instructions -
Please keep for future reference 605/8788
Dimensions
Depth - 54.5cm
Width - 114.5cm
Height - 180.5cm
617/6127
New Pagnell 3 Dr 4 Drw Wardrobe
Important - Please read these instructions fully before starting assembly
Version 1 Date: 08/11/16
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
607/9884

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Do not use this item if any
components are missing or
damaged.
• Parts of the assembly will be
easier with 2 people.
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load:
50 kgs (inside of wardrobe).
• Assembly of this product must
be carried out by a competent
adult.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• During assembly children
should be kept away from the
product due to possible risk of
injury.

2
Pilot holes for guidance only
Top panel (114.6 x 54cm)
1
Right side panel (179 x 52cm)
2
Left side panel (179 x 52cm)
3
Center panel (170.4 x 51.9cm)
4
Right middle panel (73 x 51.9cm)
5
Left middle panel (51.9 x 36.7cm)
6
Shelf x 2 (49.8 x 36.7cm)
7
Front bottom panel (111.2 x 11cm)
8
Back bottom panel (111.2 x 11cm)
9
Front panel (111.2 x 7cm)
10
Bottom support (111.2 x 7cm)
11
Back support (73 x 11cm)
12
Door x 3 (138.1 x 36.1cm)
13
Pilot holes for guidance only
Pilot holes for guidance only
Finished front edge
Pilot holes for
guidance only
Finished front surface
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

3
Large drawer front panel x 2
(72.4 x 14.5cm)
14
Large drawer back panel x 2
(69.8 x 11.5cm)
15
Drawer front panel x 2
(36.1 x 14.5cm)
16
Drawer back panel x 2
(33.5 x 11.5cm)
17
Drawer right side panel x 4
(34 x 11.5cm)
18
Drawer left side panel x 4
(34 x 11.5cm)
19
Large drawer bottom panel x 2
(70.7 x 33.6cm)
20
Drawer bottom panel x 2
(34.4 x 33.6cm)
21
Large back panel (173.2 x 75.2cm)
22
Small back panel (173.2 x 38.8cm)
23
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

4
Note: The quantities below are the correct amount to complete the assembly. In some cases mor
may be supplied than are required.
Components - Fittings
N
Nail x 54
(This screw is included
in the bag of runner)
B
12mm Screw x 24
C
Door hinge x 9
E
Rail Support x 2
F
39mm Locking pin x 27
H
Door Stop x 2
I
20mm Screw x 4
K
14mm Screw x 18
L
15mm Locking nut x 11
O
12mm Locking nut x 16
Q
Clothes rail x 1
R
12mm Screw x 8
(This screw is
A
Runner x 8
D
15mm Screw x 36
(This screw is included in
the door hinge bag)
G
30mm Dowel x 12
J
Plastic support x 8
M
50mm Screw x 17
P
30mm Screw x 16
S
Door pad x 6
V
Wall strap x 2
included in the
wall strap bag)
x 2
W
Wall plug x 2
T
50mm Long dowel x 1
U
Shelf support x 8
X
Y
Glue x 1
15mm Screw x 4
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
Z
Ventilation holes cover x 4

5
a:
Assembly Instructions
Step 1
b:
Attaching runners and
hinges
Continued on next page.
V
E
Pilot holes for
guidance only
Finished
front edge
a:
Position Runners in
front edge of the Right
side panel .
Slide top of the Runners
back.
Runners on the Right
side panel .
A
A
B
A
2
Door hinges ‘back
plates’ onto the Right
side panel .
C
D
2
Rail support on the
Right side panel .
V
E
2
2
2
2
D
C
E
D
C
D
C
A
AB
B
B
B
B
B
A
B
Middle hole
1.7cm
Note: The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
2
V
b: Slide top of Runners
forward and
A
B
.
A
B B
Middle hole
2
A
A
D
C

6
c:
Assembly Instructions
Step 1 - continued
d:
Continued on next page.
c:
Position Runners in
front edge of the Left side
panel .
Slide top of the Runner
back.
Runners on the Left
side panel .
A
A
B
A
3
3
Door hinges ‘back
plates’ onto the Left side
panel .
C
D
3
back edge
D
C
3
D
C
D
C
B
B
A
A
B
B
B
B
3
A
BB
Middle hole
A
BMiddle hole
1.7cm
3
3
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
Pilot holes for
guidance only
d: Slide top of Runners
forward and
A
B
.
A
A
D
C

7
e:
Assembly Instructions
Step 1 - continued
f:
Continued on next page.
D
E
V
E
Runners on the Center
panel .
.
B
A
4
Door hinges ‘back
plates’ onto the Center
panel .
C
D
4
Rail support on the
Center panel .
.
V
E
4
back edge
E
V
C
C
C
BB
BB
BB
BB
BB
BB
AA
AA
A
BB
Middle hole
A
BMiddle hole
1.7cm
4
4
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
Pilot holes for
guidance only
4
4
e:
Position Runners in
front edge of the Center
panel .
Slide top of the Runners
back.
A
A
4
f: Slide top of Runners
forward and
A
B
BA
BA
D
D
D
D
C

8
g:
Assembly Instructions
h:
Runners onto the
Center panel .
B
A
4
Step 1 - continued
Pilot holes for
runner position
A
B
Finished
front edge
4
4
A
B
B
B
B
B
A
B
Middle hole
1.7cm
Note: The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
4
A
B
BMiddle hole
4
g:
Position Runners in
front edge of the Center
panel .
Slide top of the Runners
back.
A
A
4
h: Slide top of Runners
forward and
A
B
.
A
A

9
Assembly Instructions
Step 2
F
Fitting locking pins
Screw Locking pins
into the Right side panel
, Left side panel
and Center panel .
F
Note:
Insert locking pins
as far as shown.
Do not over tighten.
3
2
F
2
F
F
F
F
F
F
F
F
F
F
3
4
4

10
Assembly Instructions
Step 3
Step 4
Fitting dowels
Insert Dowels and
Long dowel into Right
middle panel ,Left
middle panel ,Front
bottom panel and
Back bottom panel .
G
5
Stop onto the Right
middle panel .
H
I
H
I
6
5
89
G
H
I
G
G
G
G
G
G
G
G
G
T
T
Finished
front edge
Finished
front edge
Finished
front surface
b:
a:
Attaching plastic
supports
a:
Plastic supports onto
the Front panel and
Bottom support .
K
10
J
b:
Front panel onto the
Front bottom panel .
Bottom support onto
the Back bottom panel
.
K
10
K
K
J
10 11
89
K
J
K
K
K
K
K
K
K
K
11
11
8
9
Finished
front edge
back surface
5
6
8
9
K
JK
JK
J
K
JK
JK
JK
J
11
10
K

Step 5
Assembly Instructions
11
Attaching right middle
panel
Step 6
Attaching front bottom
panel
4
5
4
8
Right middle panel
onto the Center panel
.
M
4
5
M
M
M
Front bottom panel
onto the Center panel
.
M
4
8
5
back edge
T
4
5
T
Note:
2 people are need
at this stage.

4
9
M
Step 7
Assembly Instructions
12
Step 8
Attaching back bottom
panel
bottom panel onto
the Center panel .
M
4
9
Attaching back
support
support onto the
Center panel .
M
4
12
4
12
M
G
Insert Dowels into the
Back support .
12
G
Finished
front edge

Step 9
Assembly Instructions
13
Step 10
Attaching right side
panel
Insert 2 Locking nuts
into the Left middle panel
.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
L
L
Attaching left middle
panel
Insert 5 Locking nuts
in the Back support ,
Right middle panel ,
Back bottom panel
and Front bottom panel
.
L
5
Use a screwdriver to turn
Locking nuts clockwise
to lock.
L
8
9
12
Position Right side panel
onto the unit.
2
6
Position Left middle panel
onto the unit.
6
L
L
L
L
L
L
L
4
5
89
212
L
L
4
6
back edge

Step 11
Assembly Instructions
14
Step 12
Insert 4 Locking nuts
into the unit.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
L
L
Attaching left side
panel
1
a:
Door Stop onto the
Top panel .
Attaching top panel
Continued on next page.
a:
H
I
H
I
H
1
I
Position Left side panel
onto the unit.
3
Finished
front edge
3
6
8
9
L
L
L
L
L

Step 12 - continued
Assembly Instructions
15
M
b:
Top panel onto the
unit.
1
b:
a:
Step 13
Fixing back panels
a: Apart the Ventilation
holes covers rst.
Attach Ventilation holes
covers onto Large back
panel and Small back
panel , comebine the
covers.
22
23
Z
Z
Z
Z
Z
Z
Continued on next page.
22
23
back edge
M
M
M
M
M
M
M
3
4
2
1

N
22
23
back surface
3
9
Step 14
Assembly Instructions
16
Large drawers
assembly
a: Screw Locking pins
F
into 4 holes shown on
back of the Large drawer
front panel .
b:
Fix Drawer left side
panel onto the Large
drawer front panel .
19
14
a:
b:
b:
F
14
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Continued on next page.
F
F
F
F
14
14
19
Step 13 -
continued
Important:
The unit MUST
be ‘square’ when
back is attached.
b: Attach Large back
panel and Small back
panel onto the unit
using Nails .
N
22
23

Step 14 -
Assembly Instructions
17
continued
20
15
d: Insert 2 Locking nuts
into the holes (they will
only insert one way).
Carefully slide the Large
drawer bottom panel
into the grooves.
O
Use a screwdriver to turn
Locking nuts clockwise
to lock.
O
e: Place a small amount
Y
of Glue into the groove
on the Large drawer back
panel .
Place a small amount of
Y
Glue into the grooves.
d:
e:
20
back surface
Y
Y
O
O
14 19
18
15
Y
Y
O
Continued on next page.
18 14
panel onto the Large
drawer front panel .
c: Fix Drawer right side
Insert 2 Locking nuts
into the holes (they will
only insert one way).
O
Use a screwdriver to turn
Locking nuts clockwise
to lock.
O
c:
14 19
18
O
O
O

Assembly Instructions
a: Drawer assembly
b:
c:
a: Screw Locking pins
into 4 holes shown on
back of the Drawer front
panel .
b:
Fix Drawer left side
panel onto the
Drawer front panel .
19
16
18 16
panel onto the
Drawer front panel .
c: Fix Drawer right side
Insert 2 Locking nuts
into the holes (they will
only insert one way).
O
Use a screwdriver to turn
Locking nuts clockwise
to lock.
O
F
16
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Continued on next page.
18
F
O
Step 15
f: Position Large drawer
back panel onto the
unit using Screws .
15
P
f:
Repeat with remaining
1 large drawer.
16
19
18
O
O
F
F
F
F
16
16
19
15
20
19
P
P
P
P
Step 14 -
continued

Assembly Instructions
Step 15 - continued
d:
e:
f:
19
21
17
d: Insert 2 Locking nuts
into the hole (they will
only insert one way).
Carefully slide the Drawer
bottom panel into the
grooves.
O
Use a screwdriver to turn
Locking nuts clockwise
to lock.
O
e: Place a small amount
f: Position the Drawer
the unit using Screws .
17
Y
P
of Glue into the groove
on the Drawer back panel
.
Place a small amount of
Y
Glue into the grooves.
d:
e:
f:
Repeat with remaining
1 drawer.
Y
17
Y
Y
16 19
18
21
Y
OO
17
P
P
19
back surface
21
O