Argos 833/2811 User manual

Under Basin Storage Unit
Dimensions
Width - 48cm
Depth - 30cm
Height - 60cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800
Assembly Instructions- please keep for future reference 833/2811
Issue 1 - 01/09/10
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 640 0800
Assembly Instructions
Step 9
Connect back panels 8
using 10 x back panel
screw E as shown.
Step 10
Insert 4 x shelf bracket
L inside the unit at the
desired height as shown
and set internal shelf 9
in place.
Assembly complete.
8
8
E
L
9

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
pages 1 and 2.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp
cloth and mild detergent, do
not use bleach or abrasive
cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Components - Panels
Please check you have all the panels listed below
1 Top x 1
(48(w)cm x 30(d)cm)
2 Left side x 1
(58.5(h)cm x 28.5(d)cm)
3 Right side x 1
(58.5(h)cm x 28.5(d)cm)
4 Base x 1
(40(w)cm x 28(d)cm)
5 Plinth x 1
(6(h)cm x 40(w)cm)
6 Left door x 1
(49.2(h)cm x 19.7(w)cm)
7 Right door x 1
(49.2(h)cm x 19.7(w)cm)
8 Back panel x 2
(52(h)cm x 9.5(w)cm)
9 Shelf x 1
(40(w)cm x 25.6(d)cm)
1

Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 0845 640 0800
Please check you have all the ttings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
A B C D
35mm Male camlock x 8 Female camlock x 8 14mm Screw x 2 Magnetic catch x 1
E F G H
Back panel screw x 10 Wooden dowel x 5 Hinge x 4 Knob x 2
I J K L
16mm Screw x 2 Catch plate x 2 10mm Screw x 2 Shelf bracket x 4
Tools required
Phillips screwdriver
(medium & large)
Ruler – Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
2 3
Assembly Instructions
Assembly Instructions
Step 2
Insert 4 x female
camlock B into
underside of base 4
as shown.
Step 3
Screw 2 x 35mm male
camlock A into holes at
bottom of left side 2
and right side 3
as shown.
Insert 2 x female
camlock B into the
holes at the top of left
side 2 and right side 3
as shown.
Step 4
Insert 5 x wooden dowel
F into the bottom rail 5
as shown.
Step 1
Screw 4 x 35mm
male camlock A into
underside of top 1
as shown.
Connect magnetic catch
D using 2 x 14mm
screw C.
A
1
D
C
B
4
A
A
B
B
2
3
F
5

4 5
Assembly Instructions Assembly Instructions
Step 3
Screw 2 x male camlock
A into reverse of drawer
front 13 as shown.
Step 4
Connect hinges B to
top door 5 and bottom
door 6 using 15mm
screws F as shown.
Step 5
Insert 4 x 15mm female
camlock E into under
side of top base 7 as
shown.
Insert 4 x small wooden
dowel D into top shelf
9 as shown.
Step 6
Connect top base 7
and top shelf 9 to top
right side 2.
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 7
Connect top left side 1
to exposed ends of top
base 7 and top shelf
9 as shown
Tighten female camlocks
in under side of top base
7 with a screwdriver.
Step 8
Screw 4 x male camlock
A into the under side of
top 10 as shown.
Step 9
Connect top 10 as
shown.
Tighten female camlocks
with a screwdriver.
Assembly Instructions Assembly Instructions
Step 5
Connect plinth 5 to
underside of base 4
as shown.
Step 6
Connect assembly
completed in Step 5 to
left side 2 as shown.
Tighten female camlocks
in underside of base 2
with a screwdriver.
Note: you should feel a
click when the camlocks
are secured.
Step 7
Connect right side 3 to
other end of assembly
completed in Step 5 as
shown.
Tighten female camlocks
in underside of base 2
with a screwdriver.
Note: you should feel a
click when the camlocks
are secured.
Note: it may be helpful
to have assistance from
another person with this
stage.
5
4
2
3
Step 8
Connect knobs H to
doors 6 and 7 using
16mm screws I as
shown.
Connect catch plates
J to doors 6 and 7
using 10mm screws K
as shown.
Insert a hinge G into the
top and bottom of doors
6 and 7 as shown.
Note: it may be
helpful to have
assistance
from another
person with
the next stage.
Locate door hinges in
place in base as shown,
then connect the top
panel 1 ensuring that
top hinges of doors
slot into place (a:), and
tighten female camlocks
on inside of left and right
side with a screwdriver.
H
I
J
K
G
6
7
a: