Argos Montana 412/4621 User manual

MADE IN
BRITAIN
Dimensions
Width - 120cm
Depth - 40cm
Height - 41cm
Montana - 1 Drawer 1 Door TV Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 1 - 16/04/15
Important - Please read these instructions fully before starting assembly
ALR3149
412/4621
418/5055

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 25kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
Rule
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(only use
when drilling
into walls)

Components - Panels
Please check you have all the panels listed below
2
1 2 3
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
5
Loose Shelf (DF3523)
(366 x 375mm)
Door (DF3521)
(347 x 394mm)
Drawer Front (DF3522)
(779 x 215mm)
Fixed Shelf (DF3513)
(785 x 351mm)
Drawer Back (W752-124)
(752 x 124mm)
Left Drawer Side
(W350-124LH)
(350 x 124mm)
Long Back (X804-229)
(804 x 229mm)
Short Back (X385-379)
(385 x 379mm)
Right Drawer Side
(W350-124RH)
(350 x 124mm)
7
6
4
8
9
12
13
10
14
Drawer Base (T763-347)
(763 x 347mm)
11 15
Left End (DF3511)
(353 x 378mm)
Top (DF3509)
(1200 x 396mm)
Base (DF3510)
(1200 x 396mm)
Right End (DF3512)
(353 x 378mm)
Divider (DF3520)
(353 x 378mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B
D E F
G H I
L
P
Small locking
nut (F3) x 2
C
40mm Screw (F910) x 6
N
9mm Screw (F74) x 2
Q
J
9mm Screw (F73) x 4
Knock-in Peg (F171GY) x 4
Large locking
nut (F900) x 10
Metal dowel (F901) x 12
R
Wedgefix (F639) x 4
Shelf stud (F110) x 4
19mm Screw (F461) x 2
38mm Screw (F81) x 10 13mm Screw (F63) x 4
Handle (F341) x 2
Foot
(F233) x 5
S T
Hinge (F518) x 2
Hinge plate
(F523) x 2
KM
Nail (F51) x 20
Back holder (F276) x 2
*These can also be round
O
Nail screw (F277) x 2
Drawer runner (F1004) x 2

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
A
A
C
C
CC
12 13
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
A
9
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
12
13
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
12
13
9
C
C
12
13
A
A
9
12
13
80%
x 2
9

9
9
Assembly Instructions
5
Step 4
D
D
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
11
12 13
9
10
12 13
11
10
10
D
12 13
Step 7
Fit the wedgefixes
Turn the drawer
assembly over and slide
4 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
L
D
D
L
L
L
L
L
11
12
10
12
13
11
13
H
Step 6
Attach the handle
Attach a handle to the
drawer front using
screw .
P
H
9
P
9

Assembly Instructions
6
Step 8
Step 9
Prepare the right end
a: Place a runner on
the right end as
shown. Slide back the
top of runner and use the
1st hole from the front to
fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right end .
c: Screw 2 metal
dowels into the right
end .
Insert 2 large locking
nuts into the right end
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
2
J
J
B
2
2
Q
Q
a:
b:
Front
edge
J
Q
Q
J
J
Finished
front edge
2
2
Finished
front edge
B
c:
B
B
Finished
front edge
2
B
Prepare the fixed shelf
Insert 4 large locking
nuts into the fixed
shelf .
B
6
B
B
Finished
front edge
B
B
6
A
A
A
2

Assembly Instructions
7
Step 10
Step 11
Fit the fixed shelf to
the right end
Push the fixed shelf
onto the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Finished
front edge
Finished
front edge
A
B
6
2
B
B
6
Finished
front edge
Finished
front edge
Prepare the divider
a: Place a runner on
the divider as shown.
Slide back the top of
runner and use the 1st
hole from the front to fit
the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the divider .
Screw 2 metal dowels
into the divider .
Turn the divider over
c: Insert 2 large locking
nuts into the divider
. .
B
B
3
J
J
B
3
3
Q
Q
A
3
Front
edge
J
Q
a:
b:
c:
Turn the divider over
A
A
3
3
3
Finished
front edge
J
Q
J
6
2

Finished
front edge
Polystyrene
block
Polystyrene
block
Assembly Instructions
8
Step 12
Finished
front edge
6
Fit the divider to the
fixed shelf
Push the divider onto
the fixed shelf .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
3
6
B
6
3
Step 13
A
Prepare the top
Screw 6 metal dowels
into the top .
Step 14
5
A
Finished
front edge
5
A
A
A
A
A
Fit the top
Push the top onto
the right end and
divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the right end and the
divider .
Note: To make it easier
to fit the top and base,
place polystyrene blocks
from the packaging
underneath the right end
and divider to raise them.
5
2
3
B
2
35
2
3

Assembly Instructions
9
Step 15
Step 16
Finished
front edge
Prepare the left end
Insert 2 large locking
nuts into the left end
. .
Fit 2 hinge plates onto
the left end , making
sure that the slot is
facing towards the front
edge.
S
B
1
1
S
S
B
B
1
S
Fit the left side
Push the left side
onto the top .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the left side .
Note: Place a
polystyrene block from
the packaging
underneath the left side
to raise it.
1
5
B
1
Finished
front edge
Polystyrene
block
5
1