Argos Camden 244/3012 User manual

MADE IN
BRITAIN
Dimensions
Width - 80cm
Depth - 49.5cm
Height - 200.5cm
Camden - 2 Door Tall Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 25/03/14
Important - Please read these instructions fully before starting assembly
ALR2988
244/3012
227/6117
Issue 2 - 25/03/14
Remove old cat codes and add new ones

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 47kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
4
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3
Left Side (DF1A1)
(1970 x 491mm)
Right Side (DF2A1)
(1970 x 491mm)
Top (DF3A1)
(796 x 492mm)
Door (DF7A1)
(1868 x 357mm) x 2
Horizontal (DF4A1)
(722 x 473mm) x 2
Back Rail (DF6A1)
(722 x 130mm)
Back (X1882-740)
(1882 x 740mm)
6
Hanging Rail (FHR715)
(715mm long)
7
89
Plinth (DF5A1)
(722 x 96mm)
5

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
Electric drill
(only use
when drilling
into walls)
B C
D E F
G H I
Nail (F51) x 35
M
L
Hinge plate
(F523) x 8
Rail Holder
(F891) x 2 13mm Screw (F63) x 20
Hollow core
locking nut
(F892) x 4
Small metal dowel
(F893) x 4
19mm Screw (F461) x 4
Metal dowel (F901) x 12
Large locking
nut (F900) x 12
Hinge (F522) x 8
A
Wooden dowel (F22) x 8
N
Handle (F309) x 2
J K
Bracket (F327) x 1
13mm Screw (F79) x 1

Finished
front edge
Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
L
Prepare the left side
a: To fit the rail holder
. , screw through the
top hole with screw
and into the shallow
mark hole drilled in the
left side . Make sure
that it is fitted straight, in
line with the panel edges
and then fit another
screw using the lower
hole.
Screw 6 metal
dowels into the holes
on the left side .
Note: Tighten metal
dowels up fully against
the panel.
b: Fit 4 hinge plates
onto the left side ,
making sure that the slot
is facing towards the
finished front edge.
Push 2 hollow core
locking nuts into the
left side , making sure
that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
Note: The pin should be
tapped in flush with the
top surface of the hollow
core locking nut . b:
a:
B
B B
G
G
G
G
G
G
G1
B
B
L
L
L
L1
F
E
F
F
E
F
E
E
F
F
1
G
1
L
1
B
B
B
1

G
Assembly Instructions
5
Step 2
Prepare the right side
a: To fit the rail holder
. , screw through the
top hole with screw
and into the shallow
mark hole drilled in the
right side . Make sure
that it is fitted straight, in
line with the panel edges
and then fit another
screw using the lower
hole.
Screw 6 metal
dowels into the holes
on the right side .
b: Fit 4 hinge plates
onto the right side ,
making sure that the slot
is facing towards the
finished front edge.
Push 2 hollow core
locking nuts into the
right side , making
sure that they are flush
against the panel’s
surface.
Using a hammer, tap in
the pin on the hollow
core locking nut .
E
F
F
2
G
2
L
2
B
B
2
G
F
E
F
G
G
G
G
Finished
front edge
Finished
front edge
L
L
L
B
B
L
2
2
L
b:
a:

Finished
front edge
Finished
front edge
Finished
front edge
A
Assembly Instructions
6
Step 3
Prepare the 2
horizontals
Insert 4 large locking
nuts into each of the
2 horizontals .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 2 wooden dowels
into each of the 2
horizontals .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
4
A
H
10mm
A
4
H
A
H
H
H
H
4
Finished
front edge
x 2
G
Fit the 2 horizontals
to the right side
Push the 2 horizontals
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted
each horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 4
4
4
2
H
H
H
4
4
2

A
A
Prepare the top
Screw 4 small metal
dowels into the holes
on the top .
Note: Tighten metal
dowels up fully against
the panel.
Assembly Instructions
7
Step 5
C
C
3
C
C
C
C
3
Finished
front edge
C
B B
Fit the top
Attach the top onto
the assembly.
Note: You will need to
slide the 2 small metal
dowels into the top
of the 2 hollow core
locking nuts .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they will
go.
3
C
B
B
Step 6
Step 7
2
3
A
H
H
H
H
A
Prepare the plinth and
the back rail
Insert 2 large locking
nuts into the plinth
and 2 into the back rail
. .
Tap 2 wooden dowels
into the plinth and 2
into the back rail .
A
H
5
5
6
6
5
6

Assembly Instructions
8
Step 8
5
6
Fit the plinth and the
back rail
Push the plinth and
the back rail onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted
to the plinth and
back rail .
Note: Support the
end of the plinth
and back rail until the
left side has been fitted.
5
2
5
H
5
6
6
6
2
Step 9
C
B B
Fit the left side
Push the left side
onto the assembly.
Note: You will need to
slide the 2 small metal
dowels into the top
of the 2 hollow core
locking nuts .
Insert a screwdriver into
the 2 hollow core locking
nuts and turn the nuts
inside as far as they
will go.
Use a screwdriver to
tighten the 6 large
locking nuts fitted
to the horizontals ,
plinth and back
rail .
1
C
B
B
H
6
9
55
6
1
4
4
1

Assembly Instructions
Step 10
Warning: The
robe is heavy.
Lift with care.
9
Fit the back panel
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit, coloured
surface facing down.
Note: The back must be
positioned so that it is
central on the unit.
Nail around the
outside edges of
the back .
Note: Nails should
try to be spaced
out evenly.
Stand the unit up for
the next stage.
9
D
9
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
6
y
y
y
x
x
b:
D
9