Arregui FORMA C Instruction Manual

<ES>
FORMA C
stick the serial no.
<EN> Instruction manual and guarantee for the FORMA C safe.
<ES> Manual de instrucciones y garantías de la caja fuerte FORMA C.
<PT> Manual de instruções e garantia da caixa forte FORMA C.
<IT>
Manuale di istruzioni e garanzia della cassaforte FORMA C.
<FR> Manuel d’instructions et garanties du coffre-fort FORMA C.

<EN>
INSTRUCTIONS
Thank you for purchasing this FORMA C safe. We advise you to read the
instructions before you install and use the safe to prevent its improper use
from making the guarantee void.

<EN>
WARNING:
Each time a key is pressed, the safe emits a short beep, which
means that it was pressed correctly. If more than 15 seconds
pass between pressing two keys, the safe will close.
In this event, repeat the process.
123
456
789
0
123
456
789
0
1. OPENING FOR THE FIRST TIME:
When opening the safe for the first time, proceed in the following manner:
•Puttheemergencykey,whichisintheenvelope,intothelock.
•Turnithalfaturntotheright(clockwise).
•Thenturnitahalfturntotheleft(originalposition)andremovethekey.
•Openthesafewiththeusualkey(2halfturnstotheright).
In order to function, the safe needs 4 x 1.5 V alkaline batteries that are
placed in the battery holder located at the back of the door. In order to
insert them, open the cover of the battery holder and place the batteries
according to the diagram that is found on the inside. On completion of this
process the electronic system will be activated.
 Toclosethesafe,simplyturnthekey2halfturnstotheleft (anti-
clockwise).
2. OPENING AND CLOSING THE SAFE:
•Pressthekey.Agreenlightwillbegintoash(ifitisred,see point:
6. “Condition of the battery indicator”).
•Enteryourpersonalopeningcode.Thelightwillcontinuetoash.
•Pressthekeyandturnthekeytwohalfturnsinthelocktotheright
(clockwise). If the entered code is correct, the light will be illumi-
nated continuously for 3 seconds and a long beep for acceptance will
sound; you have this time to turn the key and open the safe. If the
entered code is incorrect, 4 short deep sounding beeps will sound
and the light will go out. In this event, repeat the process. The safe will
allow up to 5 incorrect code entries before becoming blocked for 15
minutes as a security measure, during which it will emit a beep every 5
seconds. During this time it is not possible to use the keypad.
To close the safe,simplyturnthekey2halfturnstotheleft(anti-
clockwise).
CHARACTERISTICS OF THE PRODUCT
FRONT DIAGRAM
OF THE SAFE:

<EN>
3. CHANGING THE OPENING CODE:
Theinitialopeningcodeforthesafeis1234.Tochangeit,proceedinthe
following manner:
•Openthesafeanddonotcloseituntiltheprocesshasbeenconcluded.
•Introduceabluntobject(e.g.apen)intothecircularholethatisonthe
back of the door, until it reaches its limit. The safe emits a long beep at
the beginning of the changing process.
•Enterthenewcodethatyouhavechosen.Rememberthatitmusthave
aminimumof1andamaximumof12digits.
•Pressthekey.
•Enteryournewcodeforasecondtime.Thiswaythesystemchecks
that there was no involuntary error the first time it was entered.
•Pressthekeyagain.    
The safe will emit a continuous sound for acceptance, if the process
is completed correctly. If there has been an error it will emit four short
beeps. In this second case the opening code has not been changed and
you will have to repeat the process.
4. EMERGENCY OPENING:
Together with these instructions an envelope is provided which contains:
4.1. An emergency key:
In case you do not remember your opening code, or the safe suffers
someanomaly,suchasthebatteriesgoingat,etc.,youcanopenthe
safe by means of an emergency key.
To do this, proceed in the following manner:
 •Puttheemergencykeyinthelock.
 •Turnithalfaturntowardstheright(clockwise).
 •Thenturnithalfaturntowardstheleft(initialposition)andremove
the key.
 •Openthesafewiththenormalkey(2halfturnstowardstheright). 
On completing the process the electronic system will reactivate.
4.2. An emergency code:
In the event that you cannot remember your personal code, you can
open the safe by pressing this emergency code instead of your usual
oneandfollowingthestepsindicatedinpart2.  
For your security we recommend not changing this code.
If you need to change it, follow these instructions:
 •Openthesafeanddonotshutituntiltheprocesshasbeenconcluded.
 •Pressthekeyandthenkey8.
 •Introduceabluntobject(e.g.apen)intothecircularholethatison 
the back of the door, until it reaches its limit. The safe emits a long
beep for the beginning of the changing process.

 •Enterthevalidemergencycode(thatwhichisintheenvelopeifit 
is the first change or that now programmed in if you have previously
changedit).
 •Pressthekey.
 •Enterthenewemergencycodethatyouhavedecidedon.Remember
thatitmusthaveaminimumof1andamaximumof12digits.
 •Pressthekey.
 •Forvericationre-enteryournewemergencycode.
 •Pressthekeyagain.
The safe will emit a long beep for acceptance if the process has been
completed correctly. If there has been an error it will emit four short
beeps. In this second case the opening code has not been changed and
you will have to repeat the process.
5. USE OF THE EXTERNAL BATTERY CHARGER:
 Intheeventthatthesafehasatbatteriesandyoudonothavethe
emergency key, you can open the safe by using 1 external 9V battery.
Proceedinthefollowingmanner:
•Connectthe2extremesofthebatterytothe2powerpointsthatare
onthekeypad(+y-).
•Openthesafeinthenormalway(-code-).
6. CONDITION OF THE BATTERY INDICATOR:
Each time that you use the safe, the electronic system verifies the
condition of the batteries. If the condition is good, the safe uses the
green light during the opening process. If the batteries are low the safe
uses the red light.
Once you see that the safe is using the red light, you should change the
batteries that are found on the inside of the door. The safe is able to
carry out several openings after the appearance of the red light. Even
so, do not rely on this and change the batteries as soon as possible.
<EN>
REMEMBER:
Never keep the envelope containing the emergency key and
emergency code inside the safe, in case you need to use them.

<EN>
<< On pressing , the green
light flashes; on keying in the
code a beep sounds with each
touch; but, on pressing
4 short beeps sound and the
light goes off.
<< You are pressing the keys
normally, but after a few
seconds, the light goes off and
the keys are not working.
<< You are carrying out the
opening process normally and,
when you press , the conti-
nuous green light comes on but
after a few seconds it turns off
and you cannot turn the key.
<< The safe is emitting a beep
every 5 seconds and, when you
try to press any key the safe
will not work.
<< On pressing , the red light
comes on flashing.
<< After changing the batteries
the safe continues with the red
light instead of the green.
< The entered code is incorrect,
try again.
< Too much time has passed bet-
ween pressing two keys. You have
a maximum of 15 seconds between
pressing two keys. After this time
the safe closes. Repeat the process.
< You have taken too long in tur-
ning the key or the handle. After
pressing you have 3 seconds to
turn the key or the handle.
< The safe is blocked, because
someone has keyed in an incorrect
opening code 5 times in a row.
Wait 15 minutes and the safe will
unblock automatically. Then you
can continue as normal.
< The safe is warning you that
the batteries are running out. The
safe is able to carry out several
openings after the appearance of
the red light. Even so, you should
not rely on this and should change
the batteries as soon as possible.
< It is usual that after opening
the safe for the first two or three
times after changing the batteries
the safe continues using the red
light. Check that it returns to using
the green light by carrying out
several consecutive openings. If
the problem persists check that
you have inserted the batteries
correctly.
BEFORE CALLING THE TECHNICAL SERVICE,
CHECK:

<EN>
Thesafeisguaranteedforaperiodof24monthsfromthedateofits
purchase,asestablishedbytheLaw23/2003datedJuly10thonGuaran-
tees in the Sale of Consumer Goods.
ABSS accepts the responsibility for lacks of approval declared within a
period of two years in the event of any manufacturing fault which affects
the functioning of the safe from the date of its delivery, according to the
law.Asfromtherst12months,thebuyermustprovethatthenon-
conformity already existed at the moment he received the safe.
The faults produced as a result of an improper use or installation, an
excess of humidity or salinity, water or cement filtrations, force, the
handling of the devices by non-authorized persons, disasters, impacts
and falls are excluded from the guarantee.
The repair or substitution of any part due to a fault implies a 6-month
extension to the guarantee of the part repaired or substituted. ABSS will
accept the responsibility for the non-conformities that caused this repair
when the same factory faults that caused the first repair are repeated.
IMPORTANT:
•Thesedetailsmustbecompletedasclearlyaspossibleandwithoutdelay
by the supplier, who will stamp and sign on behalf of his company in the
place indicated.
•Thecerticateremainsinthepossessionofthepurchaser.
•ThepurchasermustkeeptheRECEIPTforthepurchaseofthesafe,toge-
ther with the GUARANTEE CERTIFICATE to be able to accredit the date of
purchase. Both documents are necessary to use the guarantee.
GUARANTEE CERTIFICATE
Identity details
Name of the supplier ................................................................................................
Date of sale ..................................................................................................................
Name of purchaser ....................................................................................................
Address of purchaser ................................................................................................
Identifying details of the safe
Model ..............................................................................................................................
Series number .............................................................................................................
SUPPLIER’SSTAMP

<ES>
ATENCIÓN:
Cada vez que pulse una tecla, la caja emitirá un pitido corto, que
significa que la pulsación ha sido correcta. Si transcurren más de
15 segundos entre dos pulsaciones de tecla, la caja se apagará.
En ese caso, empiece de nuevo el proceso.
INSTRUCCIONES
123
456
789
0
123
456
789
0
Gracias por adquirir esta caja de seguridad FORMA C. Le recomendamos
que lea las instrucciones antes de instalar y utilizar la caja, para evitar
que un uso incorrecto de la misma anule la garantía.
CARACTERÍSTICAS DEL PRODUCTO
ESQUEMAFRONTALDELACAJAFUERTE:

<ES>
1. PRIMERA APERTURA:
 Paralaprimeraaperturadelacajafuerteprocedadelasiguientemanera:
•Introduzcalallavedeemergencia,queencontrarádentrodelsobre,enla
cerradura.
•Giremediavueltahacialaderecha(sentidoagujasdelreloj).
•Gireahoramediavueltahacialaizquierda(posicióninicial)ysaquelallave.
•Abralacajaconlallavenormal(2mediasvueltashacialaderecha).
 Parasufuncionamiento,lacajafuertenecesita4pilasalcalinasde1,5V,
que se colocan en el portapilas situado en la parte trasera de la puerta.
Paracolocarlas,abralatapadelportapilaseintroduzcalaspilassegúnel
dibujo que encontrará en su interior. Completado el proceso, el sistema
electrónico se activará.
 Paracerrarlacaja,simplementegirelallave2mediasvueltashacialaiz-
quierda(sentidocontrarioalasagujasdelreloj).
2. APERTURA Y CIERRE DE LA CAJA FUERTE:
•Pulselatecla .Empezaráaparpadearunaluzverde(siesroja,vea el
punto: 6. “Indicación del estado de la batería”).
•Tecleesucódigopersonaldeapertura.Laluzseguiráparpadeando.
•Pulselatecla ygirelallaveenlacerradura2mediasvueltashacia
laderecha(sentidodelasagujasdelreloj).Si el código tecleado es
correcto, durante 3 segundos la luz se iluminará fija y sonará un pitido
largo de aceptación; dispone de ese tiempo para girar la llave y abrir la
caja. Si el código es incorrecto, sonarán 4 pitidos cortos con sonido
grave y la luz se apagará. En ese caso, empiece de nuevo el proceso.
La caja permite hasta 5 introducciones erróneas de código antes de
bloquearse durante 15 minutos como medida de seguridad, durante
los que emitirá un pitido cada 5 segundos. Durante ese período, no es
posible utilizar el teclado.
Para cerrar la caja,simplementegirelallave2mediasvueltashaciala
izquierda(sentidocontrarioalasagujasdelreloj).

<ES>
3. CAMBIO DEL CÓDIGO DE APERTURA:
 Elcódigoinicialdeaperturadelacajaes1234.Paracambiarloproceda
de la siguiente manera:
•Abralacajaynolacierrehastaquehayaconcluidoelproceso.
•Introduzcaunobjetonopunzante(ej.unbolígrafo)porelagujerocircular
que se encuentra en la parte trasera de la puerta, hasta hacer tope.
La caja emitirá un pitido largo de comienzo del proceso de cambio.
•Introduzcaelnuevocódigoquehadecidido.Recuerdequedebetener
unmáximode12dígitosyunmínimode1.
•Pulselatecla .
•Vuelvaaintroducirsunuevocódigoporsegundavez.Deestamanera,
el sistema comprueba que no se ha producido un error involuntario en
la primera introducción.
•Vuelvaapulsarlatecla .
La caja emitirá un pitido largo de aceptación, si se ha completado el
procesocorrectamente.Sisehaproducidoalgúnerror,emitirácuatro
pitidos cortos. En este segundo caso, el código de apertura no habrá
cambiado y tendría que volver a empezar el proceso.
4. APERTURA DE EMERGENCIA:
 Juntoconestasinstruccionessesuministraunsobrequecontiene:
4.1. Una llave de emergencia:
En el caso de que no recuerde su código de apertura, o la caja sufra
alguna anomalía, como la descarga de pilas, etc., puede abrir la caja me-
diante esta llave de emergencia.
 Paraello,procedadelasiguientemanera:
 •Introduzcalallavedeemergenciaenlacerradura.
 •Giremediavueltahacialaderecha(sentidoagujasdelreloj).
 •Gireahoramediavueltahacialaizquierda(posicióninicial)ysaquela
llave.
 •Abralacajaconlallavenormal(2mediasvueltashacialaderecha). 
Completado el proceso, el sistema electrónico se activará de nuevo.
4.2. Un código de emergencia:
En el caso de que no recuerde su código personal de apertura, puede
abrir la caja tecleando este código de emergencia en lugar del suyo
habitualysiguiendolospasosindicadosenelapartado2. 
Porsuseguridad,recomendamosnocambiarestecódigo. 
Si necesita cambiarlo siga estas indicaciones:
 •Abralacajaynolacierrehastaquehayaconcluidoelproceso.
 •Pulselateclayacontinuación,latecla8.
 •Introduzcaunobjetonopunzante(ej.unbolígrafo)porelagujero
circular que se encuentra en la parte trasera de la puerta, hasta hacer
tope. La caja emitirá un pitido largo de comienzo del proceso de
cambio.