Aseptico ADU-04 Manual

ADU-04 Two Handpiece Man al Control System
OPERATION and MAINTENANCE
INSTRUCTION MANUAL

The Aseptico ADU-04 is one of the finest pneumatic handpiece control systems available to the
professional. Offering manual activation and easily mounted on a wall or post, the ADU-04
provides an economic control system for a dental operatory, hygienist's room, or satellite office.
Congratulations!
This system is engineered to provide many years of reliable service. Please read the instructions
provided in this manual to receive the best and longest service from your Aseptico equipment.
Separate manuals may be provided to cover the operation and maintenance of handpieces or
other accessories for your unit. Handpieces are purchased separately.
PACKAGE CONTENTS
•ADU-04 Pneumatic Control Unit
•TA-90D 3-Way Air/Water Syringe with Tip
•AA-42 Foot Control and Tubing
•Highspeed Handpiece Control
•Lowspeed Handpiece Control
Optional NWS-7
Wat r Syst m
Figure 2
OPTIONS
•NWS-7 Self-Contained Clean Water System
with AA-61 Water Connector for scalers
•Fiber Optics Kit for fiber optics handpieces
SETUP:
WATER FLOW
CONTROL
HANDPIECE
SELECTOR
AA-61
Wat r Conn ctor
1. Use the WALL OUNTING HOLES to
secure cabinet back to a flat vertical surface
(see Fig. 1)
2. Attach the front of the unit to the CABINET
OUNTING TABS using the 8 screws
provided (see Fig. 1).
3. Connect the braided airline to a clean
regulated 70-100 PSI compressed air supply.
4. Connect the blue water line to 35psi max city
water supply -OR- if using the Optional
NWS-7 Wat r Syst m, fill the white plastic
water-supply bottle with clean water and
attach the bottle to the white fitting on the
underside of the unit (see Fig. 2).
WALL MOUNTING HOLES
CABINET MOUNTING TABS
Figure 1

Handpi c S l ctor:
Selects high-speed (HP1) or low-speed
(HP2) handpiece operation.
Wat r On/Off Toggl :
Controls the on/off flow of water coolant to
the high-speed handpiece.
Wat r Flow Control:
Adjusts the water coolant flow to the high-
speed handpiece.
Pr ssur Gaug :
Gives a visual indication of the drive air
pressure to the handpiece in use.
Driv Air Pr ssur Control:
Adjusts the drive air pressure to the high
and low-speed handpieces.
Figure 3 DEPRESS
LOCKING COLLAR
Foot Control:
Controls the drive air pressure to the
active handpiece. Apply light foot
pressure to any part of the foot control
cover.
3-Way Air /Wat r Syring :
Delivers air, water, or a combination mist.
Supplied with autoclavable tip.
NWS-7 Wat r Syst m (Optional):
White 1-liter bottle dispenses water
through the 3-Way Air/Water Syringe and
high-speed handpiece.
AA-61 Wat r Conn ctor:
Provides water via standard 1/4” quick
disconnect to independent Cavitron or
scaler units requiring a water supply.
OPERATION FUNCTIONS: (Refer to Fig. 2)
UNIT OPERATION:
Handpi c s - Connect the proper high-speed
and low-speed handpieces to their appropriate
connector. Switch the handpiece selector tog-
gle to the desired handpiece. Depress foot
control for operation.
3-Way Air/Wat r Syring - Depress the right
button for air operation, and the left button for
water operation. Depressing both buttons will
create a mist. The syringe features quick-
change autoclavable tips: To remove a tip,
press on the locking collar surrounding the tip
socket and pull the used tip straight out of the
socket (see Fig 3). To insert a new tip, press
locking collar and push tip into socket as far
as it will go. Release collar and gently tug on
tip before using to ensure that tip is securely
locked into socket.
CLEANING
Syring Tip St rilization:
1) Remove contaminated syringe tip.
2) Remove all visible signs of contamination
before autoclaving.
3) Autoclave tip at 132° C (270° F) for ten minutes.
4) Sterilize between each patient use.
NOTE: Since only the tips can be autoclaved,
it is recommended that the air/water syringe
be bagged with a disposable, single-use
plastic sleeve between each patient use.
Wat r Lin s: Disinfect the water lines weekly.
Prepare a 1:10 bleach solution (1 part
household bleach to 10 parts water). Remove
water reservoir and discard residual water.
Replace empty water supply tank and air
purge all waterlines. Fill water supply tank with
bleach solution. Run bleach solution through
all lines. Allow bleach solution to stand in lines
for 10 minutes. Remove water supply tank and
discard bleach. Flush water supply tank and
all lines thoroughly with clean water. Air purge
and leave lines dry until next clinical use.

P/N 420285
Rev. H
ECO 14684
03/2019
Printed In The USA
P.O. Box 1548, Woodinville, WA 98072
8333 216 th Street S.E. Woodinville, WA 98072
[phone] • [phone]
www.aseptico.com • [email protected]
WARRANTY
Aseptico warrants its products against defects in material or workmanship for a period of two (2)
years, from date of original invoice. Some handpieces are warranted for one year under the
same conditions. Other handpieces and expendable components, such as air turbines and light
bulbs, are covered by shorter warranty periods, or have no warranty. Aseptico's sole obligation
under product warranty is (at its sole option and discretion) to repair or replace any defective
component or product in part or whole. Aseptico shall be the sole arbiter of such action.
In the event of alleged defect under warranty, the purchaser is to notify Aseptico's Customer
Service Department promptly. Customer Service will provide instructions, usually directing that
the product be returned for service. Shipment to Aseptico and the cost thereof is always the
responsibility of the purchaser.
Accidental misuse, inappropriate installation, or failure to perform directed maintenance voids the
warranty. Deliberately defacing, modifying, or removing the serial number voids the warranty.
Aseptico does not assume, under this warranty, any risks or liabilities arising from the clinical use
of its products, whether or not such use involves coincidental utilization of products manufactured
by others.