Aseptico AEU-27A Manual

AEU-27A Electronic Endodontic System
OPERATION AND MAINTENANCE
INSTRUCTION MANUAL

P.O. Box 1548 • Woodinville, WA 98072
8333 216 th Street S.E. Woodinville, WA 98072
International [phone] • Toll ree(800) 426-5913
www.aseptico.com • [email protected]
RX: FEDERAL LAW RESTRICTS THIS DEVICE TO
SALE BY OR ON THE ORDER OF A DENTIST
This device has been tested and found to comply with the emissions
requirements of IEC 60601-1-2:2001-09. These requirements provide
reasonable protection against harmful electromagnetic interference in
a typical medical installation. However, high levels of radio-frequency
(R ) emissions from electrical devices, such as cellular phones, may
disrupt the performance of this device. To mitigate disruptive
electromagnetic interference, position this device away from R
transmitters and other sources of electromagnetic energy.
i.
CLASSIFICATIONS:
• Class I Equipment
• Type B Equipment
• Ordinary Equipment - degree of protection against ingress
of water
• Not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
IN ORMATION CONCERNING THE ACCURACY AND
PRECISION O THIS PRODUCT MAY BE OBTAINED
UPON REQUEST BY CONTACTING ASEPTICO AT THE
ADDRESS SHOWN ON THIS PAGE.
TABLE OF CONTENTS:
Introduction . . . . . . . . . . . . . . . . . . . . . . . .1
Package Contents . . . . . . . . . . . . . . . . . . .1
Indications for Use . . . . . . . . . . . . . . . . . .2
Contraindications . . . . . . . . . . . . . . . . . . .2
Adverse Reactions . . . . . . . . . . . . . . . . . .2
Warnings & Safety Precautions . . . . . . . .2
Step-By-Step Instructions . . . . . . . . . . . .4
Setting Up the Unit . . . . . . . . . . . . . . . .4
Quick Start Operation . . . . . . . . . . . . . .6
Chart-1 Default Series . . . . . . . . . . . . . .8
Control Panel unctions . . . . . . . . . . . .9
Chart-3 ile Library . . . . . . . . . . . . . . .13
General Operation . . . . . . . . . . . . . . . .14
• Manual Mode . . . . . . . . . . . . . . . .14
• Series Mode . . . . . . . . . . . . . . . . .15
Advanced Operation & unctions . . . .16
• System Setup Options Menu . . . .16
RECALL ACTORY SETUP . . . . . . . .16
AUTO-STOP MODE . . . . . . . . . . . . .16
REVERSE BEEPER . . . . . . . . . . . . . .17
TORQUE WARNING . . . . . . . . . . . . .17
ACCESSORY WARNING . . . . . . . . . .17
SLEEP MODE . . . . . . . . . . . . . . . . . .18
KEYPRESS BEEP . . . . . . . . . . . . . . .18
SYSTEM VOLUME . . . . . . . . . . . . . .18
SAVE SETTINGS . . . . . . . . . . . . . . . .19
• Editing and Creating Series . . . . .20
Reprogramming the Unit . . . . . . . . . . . .25
Maintenance & Sterilization . . . . . . . . . .26
Troubleshooting . . . . . . . . . . . . . . . . . . .28
Specifications . . . . . . . . . . . . . . . . . . . . .29
Changing the Fuse . . . . . . . . . . . . . . . . .30
Symbol Definitions . . . . . . . . . . . . . . . . .31
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . .33
41EJ
MEDICAL -- GENERAL MEDICAL EQUIPMENT
AS TO ELECTRICAL SHOCK FIRE AND MECHANICAL
HAZARDS ONLY IN ACCORDANCE WITH:
UL 60601-1: First Edition - Medical Electrical
Equipment, Part 1 General Requirements for Safety.
ANSI/AAMI ES60601-1:2005/(R)2012 and A1:2012
C1:2009/(R)2012 and A2:2010/(R)2012 - Medical
electrical equipment—Part 1 General requirements
for basic safety and essential performance.
CAN/CSA C22.2 NO. 60601-1-08 (2013) - Medical
Electrical Equipment - Part 1 General Requirements
for Basic Safety and Essential Performance (Adopted
IEC 60601-1 2005, third edition, 2005-12), Includes
Corrigendum 1 2011.

1
Your new Aseptico AEU-27A Endodontic System is one of the finest units available to
the dental profession. The system features a high torque brushless motor, intuitive
user interface, and an easy to read digital display. These features combine to make
the AEU-27A an exceptionally powerful and convenient system for Endodontic
procedures.
Congratulations!
This system is engineered to provide many years of reliable service. Please read the
instructions provided in this manual to receive the best and longest service from your
equipment.
Separate manuals may be provided to cover the operation and maintenance of
handpieces or other accessories for your unit.
PACKAGE CONTENTS:
• AEU-27A Electronic Control Console
• Autoclavable Brushless Micromotor, P/N AE-250-30
• Autoclavable Motor Holder, P/N 461561
• Motor Holder Attaching Bracket, P/N 461653
• On/Off oot Control, P/N AE-7PM
• Power Cord
• Operation and Maintenance Instruction Manual, P/N 421029
PURCHASED SEPARATELY:
• AHP-71TI 1:5 Increaser Contra Angle Handpiece
• AHP-63 1:1 Contra-Angle Handpiece
• AHP-88MN 8:1 Reduction Latch-Head Contra Angle Handpiece
• AHP-88MNP 8:1 Reduction Push-Button Head Contra Angle Handpiece
• AHP-62MN 16:1 Reduction Latch-Head Contra Angle Handpiece
• AHP-62MNP 16:1 Reduction Push-Button Head Contra Angle Handpiece
• Memory Card, P/N MC-27A

2
Aseptico accepts no liability for direct or consequential injury or damage resulting from improper
use, arising in particular through the non-observance of the operating instructions, or improper
preparation and maintenance of this product.
CAUTION: The AEU-27A system is supplied Non-Sterile! Before first use, and before each
patient use thereafter, sterilize specified components as recommended in the
Sterilization and Maintenance section.
WARNIN : Use for intended purposes only. ailure to observe the operating instructions may
result in the patient or user suffering serious injury or the the product being
damaged, possibly beyond repair. Before using this product, make sure that you
have studied and understood the operating instructions.
CAUTION: ederal law restricts this device to sale by or on the order of a dentist.
CAUTION: Use of other dental accessories or sub-assemblies from third-party manufacturers
is the sole responsibility of the user.
CAUTION: All repairs are to be performed by authorized Aseptico service personnel only.
WARNIN : Always follow these guidelines when operating the unit:
• Never touch drills, burs, or other handpiece tips when they are still rotating.
• Handpieces should only be attached when the motor has stopped running.
WARNIN : Do not install where there is a risk of an explosion. The AEU-27A is not intended for
operation in the presence of flammable anesthetics or gases.
To prevent injury to people and damage to property, please heed relevant warnings and
remarks. They are marked as follows:
WARNIN : Serious injury or death may result if ignored.
CAUTION: Damage to property or the environment may result if ignored.
NOTE: Important additional information and hints.
INDICATIONS FOR USE:
or use in a wide range of dental procedures including; endodontic surgeries, such as drilling into
the tooth canal, and general dentistry, such as removing carious material from the dentin.
CONTRAINDICATIONS:
None Known
ADVERSE REACTIONS:
None Known
WARNINGS an SAFETY PRECAUTIONS:

3
CAUTION: In order to ensure the accuracy of torque and speed, it is recommended that
calibration be performed for each change of handpiece used for torque controlled
operations, or daily if the same handpiece is used.
WARNIN : Always comply with the endodontic handpiece and file manufacturer’s instructions
regarding maximum speeds, torques, forward and reverse directions, and use of all
instrumentation, drills, burs, etc., used in endodontic applications.
CAUTION: Connect mains power cable to a properly grounded outlet only.
WARNIN : Do not disassemble or alter the AE-250-30 micromotor, console, or foot switch.
CAUTION: Use only appliance cord Type C13,10A per IEC / EN 60320-1. Note: North America,
Denmark, Australia, and New Zealand may require hospital grade plugs. Consult
local codes.
WARNIN : Never use damaged or worn files as they may separate in the root canal.
WARNIN : Do not use this device in conjunction with an electric scalpel or on patients with
pacemakers.
CAUTION: It is recommended to always have the patient wear a rubber dam during endodontic
procedures.
WARNIN : Always use irrigating coolant when using high-speed handpieces.
CAUTION: The AE-250-30 micromotor is sensitive to damage if dropped or impacted against a
hard surface.

4
SETTING UP THE UNIT:
1. Unpack the Console and accessories (see
igure 1).
2. Install the Motor Cradle: The autoclavable
Motor Cradle can be attached to either side
of the Console or placed flat on any
adjacent tabletop surface or tray. Install the
Cradle by mounting the Cradle Bracket
onto the bottom of the Chassis with the two
screws provided (see igure 2). Align the
slot on the bottom of the Cradle with the
mounting rail on the Bracket and snap into
place.
3. Attach the supplied foot control to the
connector on the back of unit marked
" ootswitch" (see igure 3). The cord
connector and receptacle are keyed to
engage one another. Insert, then turn the
locking nut clockwise to secure.
4. Attach the remote power cord to the back
of the console (see igure 3) and plug into
a hospital-grade grounded electrical
receptacle. Confirm that the type of cord
plug cap is correct for the country of usage
and carries the proper certification
markings.
5. Connect the Motor/Cord Assembly to the
Motor Receptacle on the lower right front of
the console (see igure 1).
Fig. 2 - Motor Cradle
CRADLE
BRACKET
CHASSIS
BRACKET MOUNTIN
SCREWS
CRADLE
Step-By-Step In truction
Fig. 1 - System Components
ELECTRONIC CONTROL
CONSOLE
ON/OFF
FOOTSWITCH
HANDPIECE
& MOTOR
MOTOR CRADLE
& BRACKET
MOTOR
RECEPTACLE
LIQUID CRYSTAL
DISPLAY
MOTOR CORD

5
6. Attach the appropriate "E-Type" handpiece
to the motor as shown in igure 4.
Fig. 3 - Console Back
POWER
CORD IN
MAIN POWER
ON/OFF SWITCH
MEMORY CARD
PORT
FOOT
SWITCH IN
FUSES
E-TYPE
HANDPIECE
MOTOR
Fig. 4 - Handpiece/Motor Connection

6
After the unit has been set up, you are ready
for quick start operation as follows:
1. Turn the Power Switch on the rear panel of
the console from the 'O ' (O) to the
'ON' ( ) position. The Console Display will
turn on. An introduction will scroll across the
screen then briefly display the software
version installed:
AEU-27A Endodontic Motor
Ver. X.X
Ver. Date (Mo/Day/Yr)
The AEU-27A is programmed at the factory
to initially start up with ile Series S1 active.
Subsequently, when the power is turned on,
the last used settings will be active.
2. Insert an endodontic rotary file into the
handpiece.
3. Press and release the Ratio
button once to display the
currently selected handpiece/
ratio, then continue to press and
release the RATIO button to cycle through
and select the other available handpiece/
ratio options. (The default ratio setting is 8:1
reduction.)
4. Use the Calibration function to
calibrate the handpiece for the
AEU-27A. Before calibrating,
ensure that the correct handpiece
ratio is selected. Press and release the CAL
button.
The following prompt will display:
The unit will run for approximately 30
seconds, measuring the handpiece for an
accurate display of speed and torque
values.
CAUTION - Before calibration, ensure that
a file or bit is secured in the handpiece.
NOTE: Pressing, holding, then releasing
the CAL button will enable the system’s
advanced setup options menu. Refer to the
Advanced Operation section for complete
instructions.
If calibration is successful, the following
prompt will appear then the unit will return
to the last settings used:
If calibration fails, the following prompt will
appear advising the user to press the CAL
button to escape out of the test and then
check the motor/handpiece for problems:
l
QUICK START OPERATION
Testing In Progress...
Please Wait.
Calibration Successful!
Please Wait.
Calibration Failed!
Check Motor and Retest.
Press “CAL” to Escape.

7
5. Select the ile Series corresponding to the
endodontic rotary file you are using by
pressing the SERIES Left/Right arrow
buttons. The default ile Series are shown
in Chart 1, page 8.
Pressing the ILE Up/Down arrow buttons
will cycle through
the individual files
listed under each
Series name. (These Up/Down Arrow
buttons can also be used to navigate up or
down through the menu options.)
6. Press the foot pedal to activate motor and
begin operation. Note that the word “RUN”
displays whenever the motor is activated.
7. After 15 minutes of inactivity (see
instructions on page 18 to select desired
Sleep Mode activation period), the AEU-
27A will go into Sleep Mode to conserve
power. To exit Sleep Mode and resume
operation, press any keypad button or the
foot pedal.

8
NOTE: The Series listed above in Chart 1 are registered trademarks of
DENTSPLY Tulsa Dental Specialties.
During Calibration, the
handpiece will
operate, rotating
through a prepro-
grammed speed
range. Before
calibrating, be sure a
file or instrument is
secured in the
handpiece.
CAUTION
Chart 1 - AEU-27A Default Series
Default Series #1:
DENTSPLY Tulsa Dental Specialties Path ile®All iles
ile #1: Path ile (All iles)
Default Series #2:
DENTSPLY Tulsa Dental Specialties ProTaper Next™ iles
ile #1: ProTaper Next High All
ile #2: ProTaper Next Low All
Default Series #3:
DENTSPLY Tulsa Dental Specialties ProTaper®Universal iles
ile #1: ProTaper Universal S1 & SX
ile #2: ProTaper Universal S2 & 1
ile #3: ProTaper Universal 2, 3, 4, 5
ile #4: ProTaper Universal Retreatment D1 & D2
ile #5: ProTaper Universal Retreatment D3
Default Series #4:
DENTSPLY Tulsa Dental Specialties Vortex®04 & 06 Taper iles
ile #1: Vortex Orifice (All)
ile #2: Vortex 04, .35 through .50 taper
ile #3: Vortex 04, .25 and .30 taper
ile #4: Vortex 04, .15 and .20 taper
ile #5: Vortex 06, .35 through .50 taper
ile #6: Vortex 06, .25 and .30 taper
ile #7: Vortex 06, .15 & 20 taper
Default Series #5:
DENTSPLY Tulsa Dental Specialties GT®Series 20, 30, 40 iles
ile #1: Accessory 90, 70, 50, 35/.12 taper
ile #2: GT Yellow 20 Series, .10 and .08 taper
ile #3: GT Yellow 20 Series, .06 and .04 taper
ile #4: GT Blue 30 Series, .10 and .08 taper
ile #5: GT Blue 30 Series, .06 and .04 taper
ile #6: GT Black 40 Series, .10 and .08 taper
ile #7: GT Black 40 Series, .06 and .04 taper

9
Fig. 5 - Console Display & Controls
The intuitive user interface makes it easy to begin using your new AEU-27A. Advanced features for
editing and programming the system are discussed following the control panel descriptions.
CONTROL PANEL FUNCTIONS
MOTOR
RECEPTACLE
LIQUID CRYSTAL
DISPLAY
CALIBRATION/
SYSTEM SETUP:
• RECALL ACTORY SETUP
• AUTO STOP REVERSE
• REVERSE BEEPER
• TORQUE WARNING
• ACCESSORY WARN
• SLEEP MODE
•KEYPRESS BEEP
• SYSTEM VOLUME
• SAVE SETTINGS
• CANCEL
SPEED
INCREASE/
DECREASE
FILE NAVI A-
TION AND EDIT-
IN KEYS
MOTOR DIRECTION
FORWARD/
REVERSE
TORQUE
INCREASE/
DECREASE
AUTO-STOP-
REVERSE/
MAX TORQUE
HANDPIECE
RATIO
SELECTION
3
7
6
2
4
5
8

10
1. Main Power Switch:
Located on back of console (see igure 3).
Controls main power On/Off to the console.
2 Handpiece Ratio Selector:
Allows user to select han piece/ratio.
The RATIO button can select
handpieces/ratios in two different
ways - refer to either Aor B
below:
A. Press and release the Ratio button once
to display the currently selected handpiece/
ratio, then continue to press and release
the RATIO button to cycle through the other
available handpiece/ratio options. The
available handpiece ratios, speed, and
torque ranges for each option are shown
below in Chart 2:
The unit will automatically activate the
currently displayed option as the new
handpiece ratio. The selected ratio will
display as follows (example only):
Once a new handpiece/ratio has been
selected, the unit automatically enters
MANUAL MODE and displays the new ratio
with the current RPM and torque settings
(example below):
(Note: The speed, torque, and
forward/reverse settings can also be
changed manually - refer to paragraphs 4
- 8 on pages 11 & 12 for more information
on changing these settings.)
B. Press and hold the RATIO
button to display a list of all the
handpiece/ratio options. Then,
use the ILE Up/Down arrow
buttons to point to
the desired option
and press the
SELECT button.
The available
options are 1:5,
1:1, 8:1, 16:1, and
Cancel. Select “Cancel” to exit out of the
selection menu. The following prompt will
display (example only):
Note: The ratio designations X:Y and Y/X
are equivalent; for example, 8:1 is a U.S.
term and 1/8 is a European term.
3 CAL/SETUP Button:
Activates the Integrate
Calibration Program an
System Setup Menus.
The CAL/SETUP button initiates two
different functions: System Calibration and
System Setup - refer to A& Bbelow:
A. System Calibration:
CAUTION - Before calibration, ensure that
a handpiece is attached to the motor, the
correct handpiece ratio is selected, and a
file or bit is secured in the handpiece.
Press and release CAL button to activate
the calibration program. The following
CONTROL PANEL FUNCTIONS
- cont’
Selected Handpiece:
16:1 (AHP-62MN/MNP)
MANUAL MODE
16:1 1500 RPM 60 g-cm
SELECT Handpiece:
>16:1 (AHP-62MN/MNP)
Cancel
* No ASR
Chart 2 - Handpiece Options
Ratio Speed (RPM) To que (g•cm)
1:5 1,500 - 150,000 2 - 15*
1:1 300 - 30,000 4 - 120
8:1 40 - 3,600 30 - 800
16:1 20 - 1,800 60 - 1,500

prompt will display:
The unit will run for approximately 30
seconds, measuring the handpiece for an
accurate display of speed and torque
values. It is recommended to calibrate at
the beginning of each day and when
handpieces are changed.
If calibration is successful, the following
prompt will appear, then the unit will return
to the last settings used:
If calibration fails, the following prompt will
appear advising the user to check the
motor/handpiece for problems. Press the
CAL button to escape out of the test:
B. System Setup:
Pressing, holding, then releasing the
CAL/SETUP button will enable the
System’s Setup options menu. Refer to
the System Setup section, page 16 for
complete instructions.
4 SPEED Buttons
Allow user to select esire
spee (RPM) for
motor/han piece.
Press the SPEED Selector
Up/Down buttons to adjust
speed. The unit will
automatically enter MANUAL
mode and display the new
RPM settings with the ratio and torque
settings (example only):
Note: or speed accuracy, the Ratio
Selector must match the ratio of the
handpiece being used.
Note: Speed ranges are accurate when
the handpieces referenced on page 1 are
used with the supplied 30K motor. Speed
ranges are shown in Chart 2, page 10.
5 Forward/Reverse (FWD/REV)
Button:
Sets the rotational irection of
the motor/han piece.
Press and release WD/REV
button until the desired rotation is
indicated: the green LED illuminates when
forward rotation is selected; the amber
LED indicates reverse rotation. An audible
tone will also indicate when reverse
rotation is activated. This reverse audible
tone may be adjusted or turned off as
described in the Setup Options Section,
page 17.
6 Torque Adjustment Buttons:
Allow the user to a just torque limits in
Gram•Centimeter increments.
Press the TORQUE Selector
Up/Down buttons to adjust
torque. The unit will
automatically enter MANUAL
MODE and display the new
TORQUE settings with the
ratio and speed settings
(example only):
11
MANUAL MODE
16:1 1800 RPM 60 g-cm
Calibration Failed!
Check Motor and Retest.
Press “CAL” to Escape.
Calibration Successful!
Please Wait.
MANUAL MODE
16:1 1800 RPM 90 g-cm
Testing In Progress...
Please Wait.

7 ASR/MAX Torque Button:
Allows the user to select Auto-
Stop-Reverse (ASR) or
Maximum (MAX) torque
mo es.
A. ASR Mode - For 1:1, 8:1, or 16:1 ratio
han pieces only. Auto-Stop-Reverse (ASR)
mode is indicated by the illuminated green
LED next to the button. Enable ASR mode
and press the Torque Selector Up/Down
buttons until the desired auto-stop torque
limit is indicated on the Console Display.
When the foot pedal is activated, the
rotation of the handpiece will automatically
alternate between forward and reverse
whenever the selected auto-stop limit is
reached.
Note: Other ASR configurations are
available - see Global Options Section,
page 16 for details.
B. MAX Torque Mode - For 1:1, 8:1, or
16:1 ratio han pieces only. MAX Torque
Mode is indicated by the illuminated amber
LED next to the button and a “MAX” g-cm
value on the console display. This mode
allows the motor to run at its maximum
torque level. When the MAX function is
enabled, the Auto-Stop-Reverse (ASR)
function and the torque warning tone are
automatically disabled.
IMPORTANT: When a 1:5 handpiece ratio
is selected, the ASR/MAX Torque Limit
modes are automatically disabled. The 1:5
handpiece will slow and stop under load
and then continue rotating forward once the
load is reduced.
8 File Navigation & Select Buttons:
Allows user to navigate
through Files, File
Series, menus, an text
characters when
selecting an a justing
settings.
SELECT/EDIT Button -
Selects chosen options/settings. Also
opens Save Menu when saving manual
changes to ile Series, and accesses ile
Series Edit Menu when editing ile Series
names and files (see Editing and Saving
ile Series, page 20 for more information).
SERIES ARROW Buttons - Allow user to
navigate laterally (left/right) through the ile
Series.
FILES ARROW Buttons - Allow user to
navigate vertically (up/down) through the
individual iles within each ile Series.
12
CONTROL PANEL FUNCTIONS
- cont’

13

14
GENERAL OPERATION:
Figure 6
Keypad Functions:
Note: When selecting the following Keypa Functions, use the SERIES an FILE Arrow Buttons
an the SELECT/EDIT Button (see Fig. 6) to navigate through the menu options:
Menu SELECT
& EDIT
Torque
Increase/
Decrease
Auto-Stop-
Reverse/
MAX Torque
Calibration (single press)
System Setup (press & hold)
• SETUP OPTIONS:
- Recall actory Setup
- Auto Stop Reverse
- Reverse Beeper
- Torque Warning
- Accessory Warn
- Sleep Mode
- Keypress Beep
- System Volume
- Save Settings
- Cancel
Speed
Increase/
Decrease
Motor Direction
Forward/Reverse
Ratio/Handpiece
Selection
Individual
FILE Selection
Navigate
Up/Down
SERIES
Selection
Navigate Left/Right
After the user has become familiar with the system’s keypa functions, use either 1. Manual
Mo e, or 2. Series Mo e below to begin operation:
1. MANUAL MODE - At any time, the user
can use the control panel keypad to adjust
the ratio, speed, torque, and forward/
reverse settings. When the ratio, speed, or
torque are changed manually, the Display
will indicate Manual Mode, as shown below:
Note: To escape out of Manual Mode and
switch to the Series Mode, simply press
either of the two SERIES arrow buttons.
A. Saving Manual Settings: At any time,
the user can save and store new ratio,
speed, and torque settings into any one of
the five different default Series. ollow
these steps to save new Manual settings:
1) Use the keypad buttons to change the
ratio, speed, or torque settings. The
Display will indicate Manual Mode.
2) Press and hold the EDIT button. Two
beeps will sound and then the following
Save Menu will display:
MANUAL MODE
8:1 550 RPM 132 g-cm

15
3) Using the ILE Up/Down buttons, move
the selector-arrow to the desired option
(see below) and then press the SELECT
button.
• Cancel: Returns to the previous
“MANUAL” menu without saving any
changes.
• 1 - 5: Selects the specific default Series
(S1 through S5) that will be overwritten with
the new settings. A prompt will appear,
asking for confirmation of the Series
Number (example below):
4) Move the selector-arrow to the desired
option (see below) and then press the
SELECT button.
• Yes: Saves the changes to the selected
Series. The following menu will appear, with
asterisks indicating the changed Series and
ile Names in capital letters and the ile
renamed to “USER DE INED ILE“
(example below):
IMPORTANT: This “Yes” command will
overwrite the current settings in the
selected Series. To restore the default
Series settings to this Series, either re-
enter the previous settings manually or
Recall the actory Setup (see page 16).
• No: Returns to the previous “MANUAL”
menu without saving any changes.
• Cancel: Returns to the previous
“MANUAL” menu without saving any
changes.
2. SERIES MODE - By default, the unit will
start in this Series Mode. This Mode allows
the user to quickly access up to five
different Series (see Chart 1 on page 8 for
the default Series). These default Series
settings can be customized by the user --
refer to the Editing Series instructions on
page 20.
Note: To switch to Manual Mode from this
Series Mode, simply change any speed or
torque settings using the keypad buttons.
The Display will automatically change to
Manual Mode.
Save To Series 1?
> Yes
No
Cancel
*S1-SERIES 1
*F1-USER DEFINED FILE
8:1 550 RPM 132 g-cm
Save To Which Series?
> Cancel
1
2 (etc...)

16
1. Press, hold, and then release
the CAL/SETUP button. Two
quick beeps will sound and the
following menu will display the
Setup options:
2. Using the ILE Up/Down buttons, move the
selector-arrow to the desired Setup option
and then press the SELECT button.
Prompts will appear for each option (see
descriptions below).
A. Recall Factory Setup: Restores the
default factory settings and specifications,
overwriting all previous edits and
customized settings. Press the SELECT
button. The following prompt will display:
Move the selector-arrow to the desired
command and then press the SELECT
button:
• Cancel - Returns to the previous “Setup
Options” menu without changing any
settings. All previous customized settings
will remain intact.
• YES - Recalls all factory settings. A tone
will sound and the unit will briefly show the
startup screen before displaying the default
Series S1 settings.
IMPORTANT: When any of the following
seven Setup Options settings are changed,
the new settings must be saved under the
“Save Settings” command before they are
activated. Otherwise, the last settings used
will stay active. See “Save Settings” option,
page 19, for more details.
Note: The Setup Options are system-wide
settings and are not saved into any specific
Series when programming.
B. Auto Stop Rev. (Reverse): There are
three different Auto Stop modes to choose
from. After pressing the SELECT button, the
following menu will display:
• Auto Reverse - When the Auto Reverse
mode is enabled, rotation of the handpiece
will automatically stop and reverse when
the selected torque limit is reached. When
maintaining activation of the foot pedal, the
System will automatically alternate between
forward and reverse rotation in an attempt
to free the instrument.
When the Auto Reverse mode is selected,
the unit automatically returns to the “Setup
Options” menu and displays “(AUTO)” at
the “Auto Stop Rev.” prompt. NOTE: “Auto
Stop Rev. (AUTO)” is the factory default.
• Manual Reverse - When the Manual
Reverse mode is enabled, forward rotation
of the handpiece will automatically stop
when the selected torque limit is reached.
Upon releasing and then reapplying
pressure to the foot pedal, the handpiece
will rotate in the reverse direction. The
handpiece will continue to rotate in reverse
until the foot pedal is released once again.
Recall Factory Defaults?
> Cancel
Yes
Setup Options:
> Recall Factory Setup
Auto Stop Rev. (AUTO)
Reverse Beeper (ON)
Torque Warning (ON)
Accessory Warn (OFF)
Sleep Mode (15)
Keypress Beep (ON)
System Volume (40%)
Save Settings
Cancel Auto Stop Reverse:
> Auto Reverse
Manual Reverse
Auto Stop Off
Cancel
ADVANCED OPERATION - System Setup:

17
If pressure is then reapplied to the foot
pedal, the handpiece will return to forward
rotation.
When the Manual Reverse mode is
selected, the menu automatically returns to
the “Setup Options” menu and displays
“(MAN)” at the “Auto Stop Rev.” prompt as
shown below:
• Auto Stop Off - When Auto Stop Off is
enabled and the foot pedal is activated, the
handpiece will continually rotate in the
forward direction and apply the selected
torque limit until the foot pedal is released.
• Cancel - Exits out of the “Auto Stop
Reverse” menu and returns to the previous
Setup Options menu without saving any
changes.
C. Reverse Beeper: When the Reverse
Beeper feature is enabled, an audible beep
will sound while the handpiece is rotating in
the reverse direction. After pressing the
SELECT button, the following menu will
display:
• On - Enables the Reverse Beeper sound.
“Reverse Beeper (ON)” will be displayed at
the Setup Options menu. NOTE: “Reverse
Beeper (ON)” is the factory default.
• Off - Disables the Reverse Beeper
sound. No sound will be emitted while the
handpiece rotates in reverse. “Reverse
Beeper (O )” will be displayed on the
Setup Options menu.
• Cancel - Exits out of the menu and
returns to the Setup Options menu without
saving any setup changes
D. Torque Warning: When the Torque
Warning feature is active (“ON)”, a chirping
sound will be audible when the torque level
reaches approximately 75% of the selected
torque limit. When this option is selected,
the following menu will display:
• On - Enables the Torque Warning sound.
“Torque Warning (ON)” will be displayed on
the Setup Options menu. Note: “Torque
Warning (ON)” is the factory default.
• Off - Disables the Torque Warning sound.
No tone will be emitted when the torque
reaches 75%. “Torque Warning (O )” will
be displayed on the Setup Options menu.
• Cancel - Exits out of the menu and
returns to the Setup Options menu without
saving any setup changes.
E. Accessory Warning Tone: When the
Accessory Warning Tone feature is active
(“ON)”, a warning tone will be audible when
a GT®Accessory file, ITR Emulation
Accessory file, or ProTaper®Retreatment
file is in use. When this option is selected,
the following menu will display:
• On - Enables the Accessory Warning
Tone. A warning sound will be emitted
when the above accessory files are used.
“Accessory Warn (ON)” will be displayed on
the Setup Options menu.
Setup Options:
> Auto Stop Rev. (MAN)
(etc...)
Reverse Beeper:
> On
Off
Cancel
Torque Warning:
> On
Off
Cancel
Accessory Warning Tone:
> On
Off
Cancel

18
ADVANCED OPERATION - System Setup,
Cont’ :
• Off - Disables the Accessory Warning
tone. “Accessory Warn (O )” will be
displayed on the Setup Options menu.
Note: “Accessory Warn (O )” is the
factory default.
• Cancel - Exits out of the menu and
returns to the Setup Options menu without
saving any setup changes.
F. Sleep Mode: The user can instruct the
unit to automatically enable a Sleep Mode
after 15 or 30 minutes of inactivity, to
conserve power. In Sleep Mode, the
Display will turn off and the two green
LEDs next to the WD/REV and ASR/MAX
buttons will continuously blink in an
alternating pattern. To resume normal
operation when the unit is in Sleep Mode,
press any button on the keypad or press
the foot pedal.
When this option is selected, the following
menu will display:
• OFF - Disables the Sleep Mode feature.
“Sleep Mode (O )” will be displayed on
the Setup Options menu.
• 15 min - Enables Sleep Mode after 15
minutes of inactivity. “Sleep Mode (15)” will
be displayed on the Setup Options menu.
Note: “Sleep Mode (15)” is the factory
default.
• 30 min - Enables Sleep Mode after 30
minutes of inactivity. “Sleep Mode (30)” will
be displayed on the Setup Options menu.
• Cancel - Exits out of the Sleep Mode
menu and returns to the Setup Options
menu without saving any changes.
. Keypress Beep: When the Keypress
Beep feature is active, an audible beep will
sound when any button on the keypad is
pressed. When this option is selected, the
following menu will display:
• On - Enables the Keypress Beep tone.
“Keypress Beep (ON)” will be displayed on
the Setup Options menu. NOTE:
“Keypress Beep (ON)” is the factory
default.
• Off - Disables the Keypress Beep sound.
No sound will be emitted when a keypad
button is pressed. “Keypress Beep (O )”
will be displayed on the Setup Options
menu.
• Cancel - Exits out of the Keypress Beep
menu and returns to the Setup Options
menu without saving any changes.
H. System Volume: Allows the user to
select the volume level of all system
sounds, including reverse beeper, torque
warning, accessory tone, and keypress
beep. When this option is selected, two
quick beeps will sound and the following
menu will display:
• 100%-20% - Selects the desired Volume
setting, in 20% increments, from “100%”
down to “20%”. NOTE: “System Volume
(40%)” is the factory default.
Keypress Beep:
> On
Off
Cancel
Sleep Mode:
> OFF
15 min
30 min
Cancel
System Volume:
> 100%
80%
60%
40%
20%
OFF
Cancel