Aseptico AEU-16C TORQUE PLUS+ Manual

AEU-16C TORQUE PLUS+
El ctric Lab Motor Syst m
OPERATION and MAINTENANCE
INSTRUCTION MANUAL
P.O. Box 1548 • Woodinville, WA 98072 • 8333 216th Street SE, Woodinville WA 98072
nternational [phone] • Toll Free [phone]
www.aseptico.com • [email protected]

TABLE OF CONTENTS:
ntroduction . . . . . . . . . . . . . . . . . . . . .1
Package Contents . . . . . . . . . . . . . . .1
Setting Up the Unit . . . . . . . . . . . . . . .2
Operation Functions . . . . . . . . . . . . . .3
Operation . . . . . . . . . . . . . . . . . . . . . .4
Sterilization & Maintenance . . . . . . . .5
Changing Motor Brushes . . . . . . . . . .6
Symbol Definitions . . . . . . . . . . . . . . .7
Troubleshooting . . . . . . . . . . . . . . . . .8
Warranty . . . . . . . . . . . . . .Back Cover
SPECIFICATIONS:
Console Size: 5.75” x 6” x 2.75”
(14.5 cm x 15.25 cm x 7 cm)
Console Weight: 4 lbs (1.8 kg)
Power Source: 110-120V, 60Hz or
220-250V, 50Hz
Max. Power Consumption: 190 W
ENVIRONMENTAL CONDITIONS:
Designed for indoor use only.
Altitude up to 2000 m.
Temperature range of 5º C to 40º C
Maximum relative humidity 80%.
Transient overvoltage according to nstallation Category .
Pollution Degree 2.
P.O. Box 1548 • Woodinville, WA 98072
8333 216th Street SE • Woodinville WA 98072
nternational [phone]
Toll Free [phone]
www.aseptico.com • [email protected]
LABORATORY EQU PMENT
38AJ

3
Your new Aseptico AEU-16C TORQUE PLUS+ Electric Lab Motor System is one
of the finest motor/handpiece combinations available to the professional. t is
well suited for many uses in the dental lab, including dental prothesis and other
applicable dental laboratory work.
Congratulations!
This system is engineered to provide many years of reliable service. Please
read the instructions provided in this manual to receive the best and longest
service from your Aseptico equipment.
Separate manuals may be provided to cover the operation and maintenance of
handpieces or other accessories for your unit.
PACKAGE CONTENTS:
• Electric Control Console
• Remote Power Cord
• Motor/Handpiece Combo
• Autoclavable Motor Holder
• AE-7P On/Off Foot Switch

4
SETTING UP THE UNIT:
1. Unpack the console and check that the
voltage is proper for the country of use.
Use 110V unit for 110-120V 60Hz volt-
ages, and 220V unit for 220-250V
50Hz voltages. For alternative volt-
ages (220V- 250V), confirm that the
type of plug cap is correct for the coun-
try of usage and carries the proper cer-
tification markings. Correct cord is
shipped with the console.
2. Attach the remote power cord to the
back of the console and plug into a
grounded electrical receptacle.
3. Connect the motor to the receptacle on
the lower front panel of the console.
OPTIONAL
AE-14A VAR ABLE SPEED
FOOT CONTROL
AE-7P ON/OFF
FOOT SW TCH
MOTOR/HANDP ECE
MOTOR/HANDP ECE HOLDER
CONSOLE
POWER CORD
4. nsert a bur or bit into the handpiece
collet. Do not operate the unit without
a bur or blank installed in the collet.
5. Attach the supplied AE-7P On/Off Foot
Switch to the connector on the back of
the unit marked 'Foot Switch'. An
optional variable-speed foot control
may be used instead of the On/Off
Foot Switch.
Figure 1

5
OPERATION FUNCTIONS:
1. Power Switch - Controls power on/off
to console. When turned on, console
should light up.
2. Speed Control - Controls the
motor/handpiece speed. Turn clock-
wise for increased speed, counter-
clockwise for decreased speed. The
L.E.D. speed display indicates relative
speed from minimum to a maximum of
35,000 RPM.
3. Mode Switch - Sets the unit to acti-
vate from foot switch or from power
switch. f using the foot switch, set the
mode to 'FOOT'. Set the mode to
'HAND' to activate whenever the power
switch is on.
4. Rotation Switch - Selects clockwise
or counter-clockwise rotation of the
bur. Set the rotation to 'FWD' for nor-
mal clockwise operation and to 'REV'
for counterclockwise operation.
5. Optional Foot Switch - Controls the
on/off activation of the motor/hand-
piece. Variable-speed foot switches
are also available. Plug the foot switch
into the foot switch receptacle on the
back of the console and select 'FOOT'
mode for proper operation.

6
OPERATION:
After the unit has been set up and you
have made yourself familiar with the oper-
ation functions, you are ready for opera-
tion as follows:
1. Turn the power switch on the lower left
front of the console to the 'ON' posi-
tion. The front panel display will light.
2. Set the Mode and Rotation as desired.
3. Turn the Speed Control knob until the
desired operating speed is shown on
the Speed Display.
4. When mode is set to ‘HAND’, unit will
begin operation when power is on.
When mode is set to ‘FOOT’, press
down on the Foot Control to begin
handpiece operation.
Figure 2
Figure 3
ATTACH POWER
CORD
FUSE
HOLDER
ATTACH FOOT
SW TCH
POWER
SWITCH
MODE
SWITCH

5
STERILIZATION & MAINTENANCE:
CONSOLE- The exterior of the console
may be cleaned by wiping with a soft cloth
moistened with mild detergent or disinfect-
ing solution.
MOTOR/HANDPIECE- The included
motor/handpiece assembly is NOT auto-
clavable.
• Do not attempt to disassemble the
motor or motor connector.
• Do not oil or lubricate the motor.
• Do not attach a handpiece to the
motor while the motor is running.
• Do not bend motor cord sharply.
Failure to comply with any o the
above instructions may void your
warranty
WARNING:

6
Changing Motor Brush s:
1. Unscrew the motor end.
2. Pull the plug out of motor end.
3. Unscrew the motor brushes.
4. Replace Brushes and align as shown.
5. Replace plug.and screw on end cap.

7
Serial Number
Protective earth (ground)
Speed (revolutions) ncrease
Dangerous Voltage
Attention, consult
accompanying documents
SYMBOL DEFINITIONS:
SN

8
TROUBLESHOOTING:
Problem Correction
Console does not light when
turned on.
Check console to power connection.
Check that voltage selector is set for the
proper voltage.
Check fuse. f blown, replace with 1A/250V
slo-blo fuse for 110 volts, & .5 A/250V slo-
blo fuse for 220 volts.
Check motor plug connection.
ncrease RPM.
Check that a bur is properly seated in the
handpiece and the collet is closed.
f foot switch is equipped, check foot switch
connection and depress foot switch.
Turn power switch off, wait 5 seconds, then
turn back on to reset.
mproper display.
Console lights when turned on,
but handpiece does not turn.