Aseptico AEU-14CF User manual

AEU-14CF
Emergency Field Dental Unit
OPERATION MANUAL
& PARTS LIST
Expedition

TABLE OF CONTENTS:
Introduction . . . . . . . . . . . . . . . . . . . . . . . . .1
Package Contents . . . . . . . . . . . . . . . . . . . .1
Setting Up the Unit . . . . . . . . . . . . . . . . . . .2
Operation Functions . . . . . . . . . . . . . . . . . .4
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Battery Pack Removal & Installation . . . . . .7
Sterilization & Maintenance . . . . . . . . . . . . .8
Charging the Battery Packs . . . . . . . . . . .10
Re-Packing Unit . . . . . . . . . . . . . . . . . . . . .11
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Safety Precautions . . . . . . . . . . . . . . . . . .12
Symbol Definitions . . . . . . . . . . . . . . . . . . .12
Troubleshooting . . . . . . . . . . . . . . . . . . . . .13
Warranty . . . . . . . . . . . . . . . . . . .Back Cover
To prevent injury to people and damage to
property, please heed relevant warnings and
remarks. They are marked as follows:
WARNING: Serious injury or death may result if
ignored.
CAUTI N: Damage to property or the
environment may result if ignored.
N TE: Important additional information
and hints.
SPECIFICATIONS:
Case Dimensions: 17.5 in x 11.6 in x 6.9 in
(44.5 cm X 29.5 cm X
17.5 cm)
Weight: 27 lbs. (12.25 kg.)
Volume: 0.81 ft3(0.23 m3)
Power Source: AC dual voltage
120V/230V at 50Hz/60Hz
12V/24V vehicle battery
27.6V battery pack (x 2)
Water Reservoir: 16 fl. oz. (0.423 liter)
Air Reservoir: 25.8 in3. (423 cc)
Noise Level: 64dBa @ 1 meter
Fuses: 120V: 1.25A, 250V slo-blo fuse
(Installed at Factory)
230V: 0.6A, 250V slo-blo fuse
Fuse size: 5 x 20mm
Duty Cycle for AE-200-30 Motor:
Intermittent use:
1 minute On / 3 minutes Off
Mains Current Ratings: 120V: 1.25A, 230V: 0.6A
NOTE: The appliance inlet is the mains disconnect means.
Environmental Conditions:
Operating Temperature: 2° to 49° C (35° to 120° F)
Transport/Storage Temperature:
-20° to 60° C (-4° to 140° F)
Relative Humidity: 5 to 95% non-condensing
Altitude: 0 to 2591 meters (0 to 8,500 feet)
NOTE: Air pressure instruments are set to 2591 meters
(8,500 ft) elevation. Refer to Service Manual when
adjusting system pressure.
If the integrity of the protective earth ground is in
doubt, only use battery pack or vehicle battery
power for operation.
• Type of Protection Against Electric Shock:
- Class I when system is powered by mains power
source.
-Class II when system is powered by Vehicle Battery
power source.
-Internally Powered Equipment for Battery Pack
power source.
• Degree of Protection Against Electric Shock:
-Type B Applied Part
• Degree of Protection Against Ingress of Water:
-Ordinary Equipment
• Model of Operation: -Continuous
MEDICAL EQUIPMENT WITH RESPECT
TO ELECTRIC SHOCK, FIRE AND
MECHANICAL HAZARDS ONLY IN
ACCORDANCE WITH UL 2601-1
CAN/CSA C22.2 No. 601.1
Equipment not suitable for use in the presence of a flammable
anaesthetic mixture with air or with oxygen or nitrous oxide.
This device has been tested and found to comply with the emissions
requirements of IEC 60601-1-2:2001-09. These requirements provide
reasonable protection against harmful electromagnetic interference in
a typical medical installation. However, high levels of radio-frequency
(RF) emissions from electrical devices, such as cellular phones, may
disrupt the performance of this device. To mitigate disruptive
electromagnetic interference, position this device away from RF
transmitters and other sources of electromagnetic energy.

Your new Aseptico Expedition Emergency Field Dental Unit is the most
compact, full-featured portable electric dental system available. The
AEU-14CF Expedition features an “E” type autoclavable 30,000 RPM
brushless micromotor with 1/1 ratio straight handpiece and 5/1
increaser contra-angle with fiberoptic light & water, a 3-way air/water
syringe, a self contained water system, and oil-less air compressor. The
light weight dual voltage system comes in a sturdy case for maximum
portability.
Congratulations!
This system is engineered to provide many years of reliable service.
Please read the instructions provided in this manual to receive the best
and longest service from your Aseptico equipment.
Separate manuals may be provided to cover the operation and
maintenance of handpieces or other accessories for your unit.
PACKAGE CONTENTS:
• AE-200-30 Autoclavable 30K brushless micromotor
• AHP-64 Autoclavable 1/1 straight handpiece
• AHP-72MBFO Autoclavable 5/1 increaser contra-angle with fiber-optic
& irrigation
• TA-90D Three-way air/water syringe
with tips
• Air supply bottle
• Water supply bottle with filter
• AE-7P On/Off foot switch
• Power cord
• Vehicle battery cable
• Two 27.6V battery packs
• Two Operation & Maintenance Manuals
• Two Service Manuals / Parts Lists
1.

2.
SETTING UP THE UNIT:
(REFER TO FIGURES 1, 2, AND 3)
1. Unpack the chassis case.
N TE: This system is designed to operate
with all power systems attached, and to
draw power from the highest source. It is
not advised to operate off all sources at
one time. The AEU-14CF Expedition
circuitry allows the unit to operate while
using an AC power source that is either
120V or 230V, and either 50Hz or 60 Hz.
2. For AC power, attach the power cord to the
right side of the chassis (Fig. 3) and plug
into a grounded electrical receptacle.
3. For vehicle battery power, place vehicle
battery cable into the appropriate connector
(Fig. 3). Securely connect the red positive
(+) clamp to the corresponding positive (+)
terminal of the vehicle’s battery. Securely
connect the black negative (-) clamp to the
corresponding negative (-) terminal of your
vehicle’s battery.
4. For battery pack power, attach one end of
the battery pack cable assembly to the
chassis, and the other end to the desired
pack (Fig. 2). Ensure correct pin alignment
when connecting cable to chassis socket.
It is recommended that the battery packs
be charged before each use (Refer to
Page 10).
5. Connect the motor to the connector on the
lower front panel of the chassis (Fig. 3).
Align connector to socket pins and screw
Note: Be sure the correct fuse is
used for each voltage.
120V: 1.25A, 250V slo-blo fuse
(Installed at factory)
230V: 0.6A, 250V slo-blo fuse
Fuse size: 5 x 20mm
collar into place. Attach the appropriate "E"
type handpiece to the motor (Figs. 1a, 1b,
& 1c).
(Fig. 2). Place motor in holder on the right
of the motor/syringe holder.
6. Remove syringe (Fig. 2). Place a sterilized
tip into syringe and place back into
motor/syringe holder
7. Attach the supplied AE-7P On/Off Foot
Switch to the connector on the right side of
the unit marked "Foot Switch" (Fig. 3).
8. Fill the clear Water Supply Bottle with clean
water and connect to unit. A cap has been
provided to transport with water (Fig. 2).
FI . 1a - MOTOR CONNECTION
HANDPIECE
ALI NMENT
TAB
MOTOR
ALI NMENT
SLOT
(Bulb Cover
Removed)
FI . 1b - HANDPIECE ALI NMENT
MOTOR / HANDPIECE ALI NMENT
FI . 1c - MOTOR BULB COVER
BULB COVER
(Bulb Cover
Removed)

3.
Vehicle Battery Cable In
Foot Switch Receptacle
AC Power Receptacle
FIG. 3 -C assis Inputs
FIG. 2 - Setup
Battery Pack 1
Battery Pack Cable
Handpiece / Motor
3-Way Air/Water
Syringe
Water Supply
Foot Control
Battery Pack 2
Motor Receptacle
Battery Pack In
Motor Connector

4.
1. Power n/ ff Switch – Controls power
on/off to chassis from 120V/220V AC
source. When DC power is turned on, with
AC power, the AC will override the DC
power.
2. Battery n/ ff Switch – Controls power
on/off to chassis from the battery pack or
vehicle battery DC sources (chassis
should light up when turned on). NOTE:
AC power switch does not have to be on
to run from DC power sources,.
3. Motor Speed - Controls the motor/hand-
piece speed. Press the up(+) or down(-)
button until the desired speed is obtained.
- 1/1 Ratio Handpi c :
Each push of up/down button will
increase/decrease speed by 2,600 RPM.
The LED speed display indicates relative
speed from 4,000 RPM minimum to
30,000 RPM maximum. Each LED
indicates a 5,200 RPM increment.
- 5/1 Ratio Handpi c :
Each push of up/down button will
increase/decrease speed by 13,000 RPM.
The LED speed display indicates relative
speed from 20,000 RPM minimum to
150,000 RPM maximum. Each LED
indicates a 26,000 RPM increment.
4. Fiber ptic Light – Controls light On/Off
to the handpiece and enables adjustment
of light intensity. When fiber optic light ‘On’
button is pressed, the LED lights up and
the handpiece light turns on for thirteen
seconds to allow adjustment of the light
intensity. Press the positive(+) or negative
(-) button several times to increase or
decrease intensity to desired level (five
different levels to choose from). The new
intensity setting is retained in memory until
readjusted/changed. When the dental
motor/handpiece is activated, either
manually or via the foot switch, the
handpiece light will automatically turn on at
FIG. 4 - C assis
1
2
37
6
5
4
8
9 10
11
12
13
OPERATION FUNCTIONS - REFER TO FIGURE 4

5.
the previously used intensity level (fiber
optic light switch must be ‘On’) . When the
dental motor/handpiece is turned off, the
handpiece light will stay on for thirteen
seconds before timing out.
5. Manual – Selects hand/foot control mode
of dental motor. When LED is lit, motor
can be hand activated; when LED is off,
motor can be activated via the foot switch.
6. Reverse – Selects clockwise or counter-
clockwise rotation of the motor handpiece
bur. When the LED light is on, the direction
of the bur is counterclockwise. When the
LED is off, the bur is turning clockwise.
7. Water – Controls the availability of water
to the handpieces. When LED is lit, water
is available to the handpiece.
8. Source – Indicates power source. If 120V
or 230V is powering the system, the LED
will light up. If vehicle 12V/24V is powering
the system, the vehicle LED will light up. If
only battery pack power is applied to the
unit, neither light will be on.
9. Charge – Allows the system to charge the
battery pack from a 120V/230V AC source
or vehicle battery when the LED is on. A
drained battery pack takes less than 4
hours to fully charge. The unit is designed
to charge the battery pack while operating
off 120V/220V AC power or vehicle
12V/24V power.
10. Pump – When LED is on, power is applied
to the pump to allow for air and water
pressure. When LED is off, power is
disengaged from the pump to allow for
water bottle removal without shutting
power off to the chassis or battery charger.
11. Battery Level – Indicates level of charge
for the battery pack that is connected to
the chassis. “FULL” is 32V, with a drop of
1V per LED.
12. Fault – Battery light indicates problem with
connected battery pack. Unit light indicates
problem with the system. (Refer to
Troubleshooting Section, page 13.)
13. Coolant Adj. – Controls the amount of
water flow to the handpiece - turn
clockwise to increase flow.
14. Foot Switch – When either, or both, of the
power switches are in the on position, the
foot switch (s Fig. 6) provides on/off
operation of the dental motor and water
coolant (when water LED is on) to the
handpiece .
15. Three-way Air/Water Syringe (Fig. 6) -
Pressing the left button dispenses water.
Pressing the right button dispenses air.
Pressing both buttons simultaneously
dispenses an air/water mist.
16. Water Supply Bottle (Fig. 6) - The AEU-
14CF Expedition incorporates a self-
contained pressurized water system. This
consists of a 16 ounce clear bottle
dispensing water through the 3-way
Air/Water Syringe and Handpiece Coolant.
The Water Supply Bottle attaches to the
threaded reservoir connector, located
below the pressure gauge.
To refill the Water Supply Bottle:
1. Disengage pump.
2. Unscrew bottle.
3. Fill with water.
4. Screw bottle onto reservoir connector.
5. Re-engage pump

6.
Fiber ptic Light Motor Speed
Fault IndicatorPower Source Indicator
Water n/ ff Selector
Reverse Motor Direction Selector Manual Mode Foot/Hand Control Selector
1. Attach a sterile handpiece to the motor.
2. Turn the appropriate power switch to the
"ON" position. The Front panel display will
light and the compressor will charge the
system with air if the pump LED is on.
3. Set the Manual or Foot Control Selector
and Motor Direction Selector as desired.
4. When Manual LED is on, dental motor will
begin operation. When Manual LED is off,
press down on the Foot Control to begin
handpiece operation.
5. Press the Motor Speed Increase or
Decrease until the desired operating
speed is shown on the Speed Display.
6. Set “WATER” switch to “ON” (indicated
with lit LED) for irrigation flow to the
handpiece. Adjust the Handpiece Coolant
Flow knob to desired setting.
7. Use the 3-Way Air/Water Syringe as
necessary for irrigation or drying. Use a
sterile syringe tip for each operation.
8. Press the Foot Control to activate motor
and handpiece coolant when Manual LED
is off.
OPERATION:
REFER TO FIGURES 5 & 6
After the unit has been set up and you have made yourself familiar with the operation functions,
you are ready for operation as follows:
Note: When operating from a vehicle battery
as a power source, the patient and the
operator must be at least 6 feet away from
the vehicle with no electrical contact with the
chassis of the vehicle. If the patient and/or
the operator must be in contact with the
vehicle, the AEU-14CF Expedition can be
safely powered by way of an inverter through
the AC power connection of the system with
no connection to the DC power input.
Fig. 5 - C assis Control Console
Battery Level IndicatorPumpCharge

7.
9. When the fiber optic light LED is on, the
light on the motor will turn on when either
the manual mode selector switch or foot
control is depressed. The motor light will
remain on for 13 seconds after the manual
switch or foot control is turned off.
Fig. 6 - System Components
Battery
Pack
1
Battery Pack
2
Handpiece / Motor
3-Way
Air/Water Syringe
Water
Supply Foot
Control
BATTERY PACK REMOVAL &
INSTALLATION:
1. Remove shoulder screws from the front
bracket.
2. Remove nuts from side of the bracket.
3. Slide the battery back to the left and lift to
the front. NOTE: Battery pack is retained
in key slots in the rear of the case.
4. Reassemble in reverse order.

8.
1. CHASSIS - The exterior of the chassis
may be cleaned by wiping with a soft cloth
moistened with mild detergent or
disinfecting solution.
2. HANDPIECES - Thorough cleaning and
lubrication of handpieces after each use
and before sterilization is very important to
ensure proper operation and service life of
the handpiece. Follow the instructions
provided with the handpiece for complete
maintenance and sterilization procedures.
3. M T RS - The AE-200-30 motor is fully
autoclavable. Detach the motor from motor
cord by unscrewing the metal motor to
cable connector by turning counterclock-
wise (see photo below). Steam autoclave
the motor at 132° C (275° F) for ten
minutes. Wipe down the motor cable with
disinfecting solution. We recommend also
sleeving the cable between each patient.
WHEN THE MOTOR CORD MUST BE
AUTOCLAVED, AUTOCLAVE CORD AND
MOTOR JOINED - DO NOT SEPARATE
THE CORD FROM MOTOR.
Note: Extensive autoclaving will shorten
the life of the motor cord.
STERILIZATION AND MAINTENANCE:
• Do not attempt to disassemble the motor.
• Do not oil or lubricate the motor.
• Do not attach a handpiece to the motor while the
motor is running.
• Do not bend motor cord sharply.
• Do not submerge in any solutions.
• Do not use ultrasonic cleaners.
WARNING
To autoclave motor only, without cord, detach the
motor from motor cord by unscrewing the metal
motor-to-cord connector counter-clockwise.
Motor-to-cord connector
-rings
(Replace if worn
or damaged)
Failure to comply with any of the following
instructions may void your warranty
FI . 7 - BULB COVER
BEVEL
BAND
BULB C VER
For BIEN AIR / KAV
HANDPIECE
(Shipped with Unit)
BULB C VER
For NSK
HANDPIECE
• Avoid sharply
bending the cord
when autoclaving.
AUT CLAVABLE M T R C RD
• When autoclaving,
loosely coil the
motor cord.
Tool
Guide
Hole
FI . 8 - BULB REMOVAL

9.
4. M T R BULB - The motor light bulb may
become dirty in the autoclave and require
cleaning or replacement. NOTE: Do Not
Handle Bulb With Bare Fingers. To remove
bulb, unscrew bulb cover from end of motor
housing (Fig. 7). Note: Unit comes with Bien
Air / KaVo bulb cover installed. Insert dental
pick or other small pointed instrument into
guide hole at base of bulb (Fig. 8). Slide bulb
forward until disconnected from socket in
motor housing. Wipe bulb with clean soft
cloth. Reinstall bulb with guide hole facing
outward. Carefully guide the bulb’s contact
pins back into their respective socket
holes.
5. M T R -RINGS - Replace motor O-rings
when worn or damaged (see photo below).
ently peel old O-ring out of groove and
replace with new ring (PN 520069).
Occasionally apply rubber compatible
lubricant to O-rings to maintain flexibility.
6. WATER LINES - Disinfect the water lines
weekly. Prepare a 1:10 bleach solution (1
part household bleach to 10 parts water).
Remove water reservoir and discard
residual water. Replace empty water
supply tank and air purge all waterlines. Fill
water supply tank with bleach solution. Run
bleach solution through all lines. Allow
bleach solution to stand in lines for 10
minutes. Remove water supply tank and
discard bleach. Flush water supply tank
and all lines thoroughly with clean water.
Air purge and leave lines dry until next
clinical use.
7. SYRINGE TIPS - The Three-Way Air/Water
Syringe features quick-change
autoclavable tips: To remove a tip, press
on the locking collar surrounding the tip
socket and pull the used tip straight out of
the socket (see Fig. 8). To insert a new tip,
press locking collar and push tip into
socket as far as it will go. Release collar
and gently tug on tip before using to
ensure that tip is securely locked into
socket.
Syringe Tip Sterilization:
1) Remove contaminated syringe tip.
2) Remove all visible signs of
contamination before autoclaving.
3) Autoclave tip at 132° C (270° F) for ten
minutes.
4) Sterilize between each patient use.
N TE: Since only the tips can be autoclaved,
it is recommended that the Air/Water Syringe
be bagged with a disposable, single-use
plastic sleeve between each patient use.
FIG. 8 DEPRESS
LOCKING COLLAR

10.
4. Charging From Vehicle Battery - The
system is designed to charge from a
vehicle battery, provided the vehicle
battery has 11V and sufficient amperage.
If battery is detected and the measured
voltage is less than 23 VDC, the system
will automatically charge (the charge
button LED will come on). To manually
start a system charge from a vehicle
battery, depress the charge button and the
LED will come on. If the LED button fails
to turn on, the vehicle battery will not
charge the pack. The system will
automatically stop charging when the pack
is charged (the charge LED will go out).
See IMP RTANT Note on this Page.
N TE: When operating the system from a
vehicle battery, only the battery switch on
the chassis needs to be turned on. It is not
necessary to turn on the chassis power
switch.
N TE: When not powering the system
from a battery pack or charging a battery
pack, it is recommended that the operator
disconnect the battery pack cable
assembly from the pack.
1. The primary method for charging the
battery packs is through the built-in
charger in the chassis.
2. Charging the Pack from an AC Source
or Vehicle Battery – Attach the
appropriate cable for the AC source, or
vehicle power, to the chassis. Attach the
battery pack cable assembly to the chassis
and desired battery pack (we recommend
connecting the cable to the chassis first
and then to the battery pack, and
disconnecting in this reverse order to
avoid the possibility of shorting the pins).
3. Charging from AC Source – The system
does not automatically charge with the
power cord plugged in. To charge the
pack, turn on the power switch (the unit
will light up and charge the system with air
if the pump switch is on). The battery
switch and charge button must also be
turned on (indicated when the LED lights
up). The system is designed to charge
while the instrument is in use. The system
will automatically stop charging when the
pack is charged (the LED at the charge
button will go out). See IMP RTANT Note
on this Page.
CHARGING THE BATTERY PACKS
N TE:
The battery fault light will illuminate if
battery is not connected or if a battery
fault has been detected. The battery
fault will reset when a new battery is
connected.
IMP RTANT: The Battery Packs include a
built-in thermal cutoff to protect the Packs
from overheating when charging. If the battery
charger shuts Off before a Pack is fully
charged, allow 15 minutes for the Pack to cool
down, prior to recharging. When charging both
Packs, allow 30 minutes of instrument cooling
time between Packs.

11.
CHANGING THE FUSE:
1. Remove the Fuse Holder from the Power
Inlet connector.
2. Changing the fuse:
Replace the fuse in the Fuse holder.
Replacement Fuses:
120V: 1.25A, 250V slo-blo fuse
230V: 0.6A, 250V slo-blo fuse
(Fuse size: 5 x 20mm)
3. Reinstall the Fuse Holder.
Turn the power off and unplug the unit
before following the steps below.
WARNING
N TE:
The AEU-14CF is manufactured with
250V (1.25A rated) fuses installed, if
operating with a 230V power source,
change to the 0.6A rated fuses before
operation.
RE-PACKING UNIT:
1. Remove all accessories from the unit.
2. Remove water bottle and attach cap
provided with unit when transporting with
water.
3. Position syringe so that it stands vertically
to the left of the water cap. Lay tube in
vicinity of the air bottle.
4. Place handpieces in container and place
next to battery case.
5. Place power cable between handpieces
and air bottle.
6. Place water bottle on top of handpieces, to
right side of battery case as shown.
7. Place vehicle battery cable and battery
pack cable in small pouch. Place pouch on
top of console as shown.
8. Place power cord, syringe tips, and motor
in large pouch. Place on top of battery
case as shown.

WARNING: Sterilize before first and all uses. Clean, disinfect, and sterilize new or repaired
handpieces and instruments before first use. Only use sterilized handpieces and
instruments during treatment. Non-sterile handpieces and instruments may
cause bacterial or viral infections. Always sterilize handpieces and instruments
after operation.
CAUTI N: Always examine unit components for damage before commencing treatment.
Damaged components must not be used and must be replaced.
WARNING: When operating with power from vehicle battery:
1. Patient must be six feet minimum from vehicle chassis.
2. All other devices on the system should be unpowered or
disconnected from battery to prevent electronic interference.
WARNING: Use for intended purposes only. Failure to observe the operating instructions
may result in the patient or user suffering serious injury or the the product being
damaged, possibly beyond repair. Before using this product, make sure that you
have studied and understood the operating instructions.
WARNING: For use by qualified and trained personnel only.
WARNING: Do not install where there is a risk of an explosion. The AEU-14CF is not
intended for operation in the presence of flammable anesthetics or gases.
SAFETY PRECAUTIONS:
Aseptico accepts no liability for direct or consequential injury or damage resulting from improper
use, arising in particular through the non-observance of the operating instructions, or improper
preparation and maintenance.
IPX1IPX1
Alternating current
Protective earth (ground)
Protect Against Dripping Water
Dangerous Voltage
Attention, consult
accompanying documents
SYMBOL DEFINITIONS:
Type B Equipment
12.
Do Not Throw Into Trash

Problem:
Chassis does not light when turned on:
Chassis lights when turned on, but
handpiece does not turn:
Chassis does not light when 12V/24V
power is applied:
Chassis does not light when battery
pack is applied:
Motor slowing down or sluggish:
Pressure fails to stabilize:
Pressure fails to turn off at
approximately 20 PSI:
Unit fails to build pressure:
Battery fault light on:
Unit fault light on:
AC / DC Source lights flash On/Off:
Correction:
Check chassis to power connection.
Check that voltage is proper voltage.
Check fuse. If blown, replace with 1.25A/250V slo-blo fuse for
120V operation, & 0.6A/250V slo-blo fuse for 230V operation.
Check motor plug connection.
Check foot switch connection.
Depress foot switch.
Increase RPM.
Check that an instrument is properly seated in the handpiece
and the collet is closed.
Check 12A fuse inside chassis (blue fuse wired to the
vehicle battery connector). Refer to Service Manual.
Check connections at the battery pack, chassis, and cable.
Check voltage of the battery pack
Check the 5A fuse inside the chassis (amber fuse wired to
the battery pack connector). Refer to Service Manual
Dirty, under-lubricated handpiece.
Handpiece lubricant is running into motor.
After lubricating, set handpiece with head down to let excess
lubricant drain out.
Check that air and water bottles are tight. Check line and
fittings for air leaks.
Check for broken cable to pressure switch.
Check pressure settings.
Check that bottles are tight. Check wires for breaks to
solenoid switch.
Battery not connected, or charging error observed. Allow
battery pack to cool below 35°C for 30 minutes before
attempting charge. If battery fault light is on for two
consecutive charging attempts, replace battery pack.
Unit operational error observed. Remove all power from unit
for 30 minutes before attempting to use the system again. If
unit fault light is on during two consecutive attempts to
operate the system, return system for repair.
Unit operational error. Return system for repair.
TROUBLESHOOTING:
13.

PRINTED IN
THE U.S.A.
P.O. Box 1548 • Woodinville, WA 98072
8333 216th Street SE Woodinville, WA 98072
[phone] [phone]
www.aseptico.com • [email protected]
WARRANTY
Aseptico warrants its products against defects in material or workmanship for a
period of two (2) years, from date of original invoice. Some handpieces are
warranted for one year under the same conditions. Other handpieces and
expendable components, such as air turbines and light bulbs, are covered by shorter
warranty periods, or have no warranty. Aseptico's sole obligation under product
warranty is (at its sole option and discretion) to repair or replace any defective
component or product in part or whole. Aseptico shall be the sole arbiter of such
action.
In the event of alleged defect under warranty, the purchaser is to notify Aseptico's
Customer Service Department promptly. Customer Service will provide instructions,
usually directing that the product be returned for service. Shipment to Aseptico and
the cost thereof is always the responsibility of the purchaser.
Accidental misuse, inappropriate installation, or failure to perform directed
maintenance voids the warranty. Deliberately defacing, modifying, or removing the
serial number voids the warranty.
Aseptico does not assume, under this warranty, any risks or liabilities arising from the
clinical use of its products, whether or not such use involves coincidental utilization of
products manufactured by others.
P/N: 420382
Rev. H
ECO 13123
06/2013