Aspire K1 User manual

User Manual For
Starter Kit

Welcome to Aspire ... a change you can taste!
Thank you for purchasing Aspire new high-end Vaping Kit. We hope you have many hours of enjoyment.
Before using the kit, please read through the manual for proper care and use. This will help you to achieve the best
performance from your new product. Please keep this manual for future reference.
Aspire Starter Kit

Standard configuraon
Aspire Starter Kit contains:
* 1 Aspire CF G-power 900mah baery
* 1 Aspire K1 glassomizer
* 5 Replacement 1.6Ω BVC atomizer coils
* 1 USB charger
* 1 A/C adaptor
* 1 User manual

Aspire K1 glassomizer
Replaceable Atomizer coils
(Aspire BVC)
Upper hardware
PYREX Glass tank
Drip p
Boom hardware

Filling the K1 glassomizer
1. Screw the boom
base off the tank.
2. Hold the K1 at a 45
degree angle, then
fill e-liquid into the
space between the
glass tank and the
center metal tube.

Filling the K1 glassomizer
4. Screw the boom base
onto the tank.
3. Make sure the coil be
screwed ghtly onto
the boom base.

Note: 1. Do not over-fill or get liquid into the small center hole.
2. For best performance and long clearomizer life, please allow the e-liquid to soak for 2 minutes before use.
3. Do not remove any parts, make sure all components are in place.
Filling the K1 glassomizer

Operang Your Starter Kit
1. Screw the G-Power
baery into the K1
glassomizer.
2. Push the buon on the baery
(press 5 mes in succession to
turn ON/OFF), the LED will
blink 3 mes and the buon
will illuminate Blue when
acve and ON. Press the LED
buon and inhale at the same
me. Release the buon aer
inhaling. The light indicates it
is working.

The baery needs to be
recharged when the unit
produces a decreased
vapor and/or the baery
Orange indicator light
blinks 10 mes.
To charge the baery: Unscrew the baery from the vaping
components and gently screw baery into the dedicated USB
charger provided in the kit. Plug the USB into the supplied A/C
adaptor or computer. The baery will flash 3 mes and then
turn solid in color (Orange light in 3.2-3.5V, Blue light in
3.5-4.15V). The light on the USB charger will be red when
charging. It takes approximately 3 hours for the baery to
charge. Once fully charged, the USB charger will display a green
light, and the LED light on baery will turn off.
Charging the baery

Cauons
1. When cleaning the clearomizer, please be sure to remove the coil first, thoroughly wash out any excess e-liquid and let it dry out before
reassembly.
2. The device should not be impacted, dropped or mishandled, otherwise it may cause damage and injure.
3. You should only use the dedicated USB charger provided in the kit to avoid damaging baery.
4. Please keep connectors clean. A dirty baery connecon will result in poor funcon and charging.
5. Please charge the baery fully before using to maintain a good baery life.
6. Please always keep the baery dry and away from moisture.
7. Do not over ghten the baery while screwing it onto the charger, a gentle connecon is all it needs to funcon.
8. Do not store baery in too hot or too cold environment.
9. Do not aempt to open or modify the device in any way as damage or personal injury may occur.
10. If you have a problem with the device, please contact the seller - do not try to repair it or dismantle it by yourself. This could damage
the device and endanger yourself and will invalidate the warranty.