Assa Abloy Corbin Russwin Access 800 Series User manual

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
1
Attention Installer
Access 800
®
C A U T I O N
DOOR MUST REMAIN OPEN
DURING INSTALLATION.
USE DOOR STOP.
TEST
FOR PROPER
OPERATION
BEFORE
CLOSING
DOOR
For installation assistance contact Corbin Russwin Inc., at 1-800-810-WIRE (9473)
FM335 10/18
Please read these instructions carefully to prevent missing important steps.
Please Note: Improper installation may result in damage to the lock and void the factory warranty.
Important: The accuracy of the door preparation is critical for proper functioning and security of this lock.
Misalignment can cause premature wear and a lessening of security.
Installation Instructions
Mortise Lockset
For ML20800 TCWI1/TCIP1 Series In U.S.:
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
www.corbinrusswin.com
In Canada:
ASSA ABLOY Door Security Solutions Canada
160 Four Valley Drive
Vaughan, Ontario, Canada L4K4T9
www.assaabloy.ca
®
ASSA ABLOY
WARNING
This product can expose
you to lead which is
known to the state of
California to cause cancer
and birth defects or other
reproductive harm. For
more information go to
www.P65warnings.ca.gov.
08/2018

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
2

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
3
3 Warning ..........................................................................................................
)
1
2) General Description/Specifications/Features .............................................. 4
3) ML20800 Series Product Illustration ............................................................. 5
Installation Instructions ..............................................................................
)
4
)
5
Hard Wiring Instructions ............................................................................
TCIP1 (PoE) Wiring Instructions .................................................................
)6
16
16
17
16
6.1) Important ...................................................................................................
6.2) Installation Notes ........................................................................................
®
6.3) Electrolynx Connector System Notes .......................................................
6.4) Hard Powered Connections ........................................................................
Table of Contents
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Warning: To comply with “Fire Listed” doors, only alkaline batteries must be used.
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
1) Warning
6-12
13-15
16-17
Operational Check .........................................................................................
7) 18

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
4
General Description
Specifications
• Latch •
•
•
•
•
Features
2) General Descriptions/ Specifications/ Features
The Corbin Russwin Access 800 WI1 WiFi lock uses IEEE 802.11 b/g WiFi infrastructure to
connect to the access control system, making it ideal for adding access control to areas of a
building that would be too difficult or costly to wire. With no wires to run, it significantly
reduces hardware and labor costs.
The Access 800 IP1 PoE lock uses a single Ethernet cable for both power and data, eliminating
the need for any additional power supply or electrical wiring. It uses existing IEEE 802.3af PoE
infrastructure to streamline the installation process, reduce costs, enable real-time
communication, and minimize power consumption.
• Intelligent, integrated ANSI/BHMA Grade 1 lockset, available in cylindrical lock,
mortise lock, and exit device configurations, offers the highest degree of physical
security available in access control locks
• Local decision making ensures operation regardless of network status
• Built-in door status monitoring and real-time, configurable alarm notifications
• Supports 2,400 users and 10,000 event audit trail
® ®
• Supports HID 125 kHz prox or 13.56 MHz iCLASS credentials (26 - 39 bit);
supports CSN reads for other common 13.56 MHz cards, including MiFare,
DesFire, and Felica
• Available with a keypad option for two-factor authentication
• Weatherseal gaskets and conduit included for use on exterior doors
• WiFi version (TCWI1) uses 6 AA alkaline batteries or remote electrical power
• PoE version (TCIP1) is a Class 2 device, as defined by IEEE 802.3af, requiring a
maximum of 7 watts

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
5
3) ML20800 Series Product Illustration
®
A
SSA ABL
OY

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
6
Verify hand and bevel of door. Illustrations shown are as viewed from the outside
or secure side of opening.
1
4) Installation Instructions
2Prep door according to supplied door marker.
Left Hand
Hinges Left.
Open Inward.
"LH"
Left Hand
Reverse Bevel
Hinges Left.
Open Outward
"LHR"
Right Hand
Hinges Right.
Open Inward.
"RH"
Right Hand
Reverse Bevel
Hinges Right.
Open Outward
"RHR"
7/8"
1-1/2
1/8" Dia. holes
(2) required
Slot
Attach fire stop plate
using self tapping screws
#8-32 x 1/2 long for wood &
metal doors
.C of 1-1/2 Dia
L
Outside
of Door
Hole for ribbon cable
Non Fire Rated Exterior Doors
install weather conduit.
(Hollow Doors Only)
Outside
of Door
Non Fire Rated Door
Hole for
ribbon cable
Install conduit half with recessed
panel "Not For Use On Fire Door"
visible from outside of door.
The optional conduit is available
for non fire rated doors to provide
weather protection for exterior door
applications. It is included in the M99
Weatherseal Gasketing Kit when
ordered with the device. If ordered
separately, order part number
794F929.
Fire stop plate required
for fire rated doors
FOR
USE
ON
FIRE
DOOR
NOT

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
7
4) Installation Instructions
RED Locking Screw
Catch Plate
Handing of Lock Body
Step 1) Move the red locking screw to
side of lock body being locked (Fig. 1)
Step 2) Push in latch then depress catch
plate with screw driver (Fig. 1)
Step 3) Pull latch out of lock body
and turn latch over (Fig. 2)
Figure 1
Figure 2
Figure 3
Figure 5
Step 4) Push in latch while holding
screw driver behind latch tail (Fig. 3)
Note: Push in latch until catch plate is
no longer depressed (Fig. 4)
Step 5) Rotate lock front to match
bevel of door as shown (Fig. 5)
MAKE SURE CATCH PLATE IS
EVEN W/TOP SURFACE
GOOD BAD
Figure 4
WARNING:
LOCK-IN CAN
OCCUR IF LATCH
IS NOT PROPERLY
INSTALLED
3

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
8
Lock Assembly Instructions
4
4) Installation Instructions
(2) #12x1"
Combination Screws
Lock Body
7/64 Allen Wrench
Align bevel accordingly. Engage 7/64 Allen wrench onto cap screw required for Step 5:3 on page 9.
Feed connector and wires through 1" (25) dia. wire access hole. Insert lock body into mortise cutout in
door and hold loosely in place with (2) #12x1" lock body screws.
Inside of
Door
Feed conn
through non-cylind
s
r sidee
ector & wire

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
9
5
Spindles
Keypad Ribbon Cable
Outside
of Door
Installation of Outside Escutcheon
Ground
Wire
Gasket (optional)
C A U T I O N
DOOR MUST REMAIN OPEN
DURING INSTALLATION.
USE DOOR STOP.
NOTE: Key and
cylinder must be
rotated as shown
Correct Incorrect
1. For exterior applications, an optional M99 Weatherseal Gasketing Kit can be ordered when a
device is ordered. This kit includes gaskets and a conduit. When ordering the kit separately, order
part number 794F929. The gaskets may be used as a seal between the escutcheon and the door
surfaces.
2A. For fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon through
the fire stop plate.
2B. For non-fire rated doors, feed ribbon cable connector and ground wire from outside escutcheon
through weather seal gasket (if used), then conduit sleeve in door (not shown).
3. With outside lever horizontal, insert mounting posts into the door. Make certain the lever spindle is
properly engaged in lock. (see diagram and Note A. below) Screw cylinder into mortise lock,
ensuring the cylinder orientation is in the correct position (see diagram below) . Using the 7/64 allen
wrench provided, hand tighten (5-10 in. lbs.) the cap screw to prevent unscrewing of the cylinder.
Turn the key to make certain that the locking mechanism (latch, deadbolt, key) functions correctly.
Tighten (2) #12 x 1" lock body screws. Remove allen wrench.
NOTE A.
®
For MUSÉO Lever
collections ONLY.
Thread hub into lever
and fully tighten.
Align adapter hub
with square hole in
lever, keeping hub
as tight as possible.
Use Correct Spindle Orientation
STANDARD MUSÉO
Lever
Lever
GASKET APPLICATION:
Peel off the adhesive protective paper
from gasket. Feed Trim assembly motor
harness through gasket opening as
shown and firmly press gasket to
escutcheon, aligning edge of gasket
with the edge of the escutcheon.
®
ASSA ABLOY
®
ASSA ABL
OY
4) Installation Instructions
®
A
SSA ABL
OY
®
iCLASS Cable

®
ASSA ABLOY
ElectroLynx® is a registered trademark of ASSA ABLOY Inc.
Copyright © 2014 Corbin Russwin, Inc. All rights reserved.
Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
10
Lock Body
Harness
Motor Connector
Keypad Harness
(ribbon cable)
Ground Terminal
Remote Power
DPS
Remote Power
and DPS
Antenna (iCLASS)
Antenna
(iCLASS)
Ground Wire
6Installation of Inside Escutcheon
4) Installation Instructions
Locate (3) oval head screws
and insert through the
escutcheon and thread
into the outside escutcheon.
GASKET APPLICATION:
Peel off the adhesive protective paper from gasket.
Feed Trim assembly motor harness through gasket
opening as shown and firmly press gasket to
escutcheon, aligning edge of gasket with the edge of
the escutcheon.
Inside
of door
Keypad Ribbon
Cable
Thumb Turn
C A U T I O N
DOOR MUST REMAIN OPEN
DURING INSTALLATION.
USE DOOR STOP.
NOTE: Connectors go on only one way. Do not offset connector and be sure they are completely
seated.
1. Remove black battery cover from the escutcheon with high security T20 Trox bit provided.
2. Connect ground wire to ground terminal. Keypad ribbon cable connector to controller, iCLASS
antenna (M812 & M813 only), lock body harness to motor connector, DPS connector on lock
body harness to remote power and DPS harness, and connect remote power if applicable.
3. Align thumb turn to the vertical position.
4. Push excess keypad ribbon cable into the ribbon cable hole.