Assa Abloy Lockwood Cavity Lock User manual

ASSA ABLOY is the global
leader in door opening
solutions, dedicated to
satisfying end-user needs
for security, safety and
convenience
Please Note:
This document is provided as a dimensional reference and should not be printed as a drilling
template unless it can be correctly scaled to 100% by your printer.
ASSA ABLOY Australia Pty Limited
235 Huntingdale Road,
Oakleigh Victoria, 3166
Australia
[e-mail]
assaabloy.com.au
ASSA ABLOY New Zealand Ltd.
6 Armstrong Road
Albany, North Shore City, 0632
New Zealand
[e-mail]
assaabloy.co.nz

Tear along perforated line
3
1
3
1
m
2
Mark line on the door face
approximately 900mm from
the floor. Tear along perforated
line on template. Fold page along
--- dashed line and place fold on
door edge. Align CL with marked
line on door face.
Find centre of door edge and
mark ready for drilling
Ø25mm latch hole.
Mark hole position ready for
drilling Ø54mm furniture.
If using a pre-prepared door,
use the
location of the second
Ø25mm hole.
(Go to step 6)
Drill Ø2mm pilot hole squarely
through the door.
1.
2.
template to mark the
3. Drill the second Ø25mm bolt
hole 70mm deep.
Insert bolt into Ø25mm holes,
mark around latch face plate.
Chisel out recess to suit face
plate. Face plate must be flush
with door face.
1. Drill Ø25mm latch hole to
depth of 70mm, ensure hole
is drilled squarely.
2. Drill a Ø54mm furniture hole,
from both sides of door to
prevent splintering.
Insert bolt, then drill Ø2mm
pilot holes and affix with screws
provided.
Press the retractable door pull
button to release it.
(Press it to reset).
Pull on the retractable door pull
to remove door from cavity.
Latching Passage Set door preparation and bolt with pull installation (steps 1 - 11)
Please ensure that all necessary safety precautions are taken when installing this product.
Find centre of
door edge and mark
ready for dril ing
Ø25mm bolt holes
l
Offset 37mm
- Ø54mm Hole saw
- Ø25mm Spade bit
- Ø2mm Drill bit
- Power drill
- 25mm Chisel
- Pencil
- Ruler or tape measure
- Phillips head screw driver
ools Required
Mark hole
position ready
for drilling Ø54mm
furniture hole.
Important Note
Drill hole from both sides of door
to prevent splintering of door face.
Backset 60mm
Fold here on door edge
Tear along perforated line
Guide only
5 10 15 20 25 30 35
5 10 15 20 25 30 35
Guide only
CL
Door and pull preparation template
T
Fold here on door edge
1 2 3 4
6 7 85
9 10 11
CAVITY LOCK®32MM - 40M
DOOR THICKNESS
Sliding Door Furniture
INSTALLATION OF LATCHING
PASSAGE SET
M
1300 LOCK UP
lockweb.com.au
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 © 2011
Q50117 A 042013

Latching Passage Set installation (steps 12 - 20)
Strike preparation and installation (steps 21 - 31) Door stop installation (step 32)
Furniture assembly Assembly shows both sides
interlocking.
Internal Furniture
Engages with the tailbar from
the bolt.
Internal Furniture in place. External Furniture
Engages with the tabs on the bolt.
.
est bolt with the thumb turn,
or coin edge in privacy version.
Fix furniture with the screws
provided.
Fit furniture side first. If door is less than 33 mm thick
use packers. Fit the packers to the
inner faces of the furniture,
against the door face.
T
Mark a vertical line down the
door jamb, along the edge of the
door.
Partially close door and mark
a horizontal line, centre of the
latch bolt on the door jamb.
Extend horizontal line along the
inside face of the door jamb.
Measure and halve the door
thickness.
From the vertical line on the
door jamb, measure and mark
half the door thickness. Draw a
second line.
Drill Ø25mm hole 20mm deep.
Strike basin measures 35mm
high.
Mark two lines symmetrically
either side of the Ø25mm hole
centre line.
Chisel out basin recess to depth
of hole.
Fit and mark around strike plate,
taking care to keep vertical.
Chisel out strike plate recess.
Strike plate must be flush with
jamb.
Drill Ø2mm pilot holes, affix with
screws provided.
A door stop is recommended
on the external door face when
using a key locking application.
12 13 14 15 16
17 18 19 20
21
26
31
22
27
32
23 24
29
25
3028
CAVITY LOCK®32MM - 40MM
DOOR THICKNESS
Sliding Door Furniture INSTALLATION OF LATCHING
PASSAGE SET
1300 LOCK UP
lockweb.com.au
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 © 2011