Assa Abloy SARGENT Profile Series User manual

A7787F
01/18
Copyright 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
Profile
WiFi Exit Device
Installation Instructions
v.S2

Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/18
1
2
3
4
5
6
7
Table of Contents
Warning ...................................................................................2
General Description.................................................................3
Hardware Specifications .........................................................3
Electronic Specifications.........................................................3
Lock Wiring..............................................................................4
Parts Breakdown .....................................................................5
Installation for v.S2 With 8877/8878 Rim Exit ........................9
Installation for v.S2 With 8977/8978 Mortise Exit Device....16
Operational Check .................................................................24
8
Changes or modifications to this unit not expressly approved by ASSA ABLOY Inc.
could void the user’s authority to operate the equipment.
1Warning
9
To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.
SARGENT Mfg. Co. v.S Series locksets utilizing a door position switch (DPS) are not rated for,
or intended for use in life safety applications.
!
1-800-810-WIRE • www.sargentlock.com • A7787F
FCC:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada:
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications
were met.
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des-
règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer
l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui
peut causer l’opération peu désirée.

01/31/18
A7787F 3
Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.S2 WiFi Exit Device
Hardware Specifications
General Description
The SARGENT Profile Series v.S2 Exit Device is available with either an HID® 125 kHz Prox or 13.56 MHz
iCLASS® technology reader. Either can be used in applications requiring wireless access control. The v.S2 is a
self-contained microprocessor-controlled access control product with non-volatile memory. It is able to utilize
the existing wireless LAN (802.11b/g) in order to communicate with the access control system. The v.S2 lock
will hold a total of 24000 unique users per lock.
This product is operated by six (6) “AA” alkaline batteries or by SARGENT 3267 9VDC power supply. SARGENT
Exit Devices are designed with quality components to provide high security, performance and durability.
The Profile v.S2 exit device may be used for both indoor and exterior applications. A weather protective gasket
(provided with unit) is recommended for exterior applications.
HID® and iCLASS® are registered trademarks of HID Global Corporation.
• Wireless (WiFi 802.11 b/g) online, battery-operated
• 2400 users per lock
• 10,000 event audit trail
• Centralized lock management
• Input Power: DC 9V, 1.5A (6 AA alkaline batteries
or optional hard-powered)
• Supports HID® 125 kHz prox or 13.56 MHz
iCLASS® credentials (26 - 39 bit); supports CSN
reads for other common 13.56 MHz cards, including
MiFare, DesFire, and Felica
3
Electronic Specifications
4
2
• Real Time Door Status Monitoring*
• Easy installation (no need to hardwire)
• Lockdown capable*
• Supports most current WiFi networks security standards
• For specific security information, please contact a local
ASSA ABLOY Door Security Solutions sales consultant
or call 800-810-WIRE
Profile Series Rim Exit Device
• Latch – 3/4" throw, stainless steel
• Accepts all SARGENT rim cylinders (8877 only)
• Key retracts latch (8877 only)
Profile Series Mortise Exit Device
• Latch – 3/4" throw, anti-friction, brass
• Accepts all SARGENT mortise cylinders
(8977 only)
• Key retracts latch (8977 only)
SARGENT Profile Series WiFi
v.S2 Typical Application
802.11b/g Wireless Network Device
Lock Management
Tool (LMT)
v.S2 Lock
Internal
Building
Network (Intranet)
Network
Interface
Card
Ethernet LAN
• Profile Series exit devices furnished for
1-3/4” doors
• UL Listed
• Fire stop provided on all lever handle designs
• Outside motor driven “ET” lever controlled
by keypad
• Available in “ET” lever handle designs only
• Push bar retracts latch from inside
*Lockdown and real-time door status monitoring available only when
lock is hard-powered
Profile Series Rim and Mortise Exit Devices

Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/18
4 A7787F
Profile Series v.S2 WiFi Exit Device
(+) 9V DC (RED)
(-) (BLACK)
AX/DPS NC (PINK)
AX/DPS COM (VIOLET)
Unused Unused Unused
EGND (GREEN)
DX NC (White/Green)
Unused
RX NC (Green)
Unused
LX NO (Red/Yellow)
LX COM (Red/Green)
Motor B Black)
Motor A (RED)
TB2
E1
TB1
8 7 6 5 4 3 2 1
1 2 3 4 5 6 7 8
Ground Screw to Connector to E1
Lock Wiring
5
Controller Board Connectors
(Inside Escutcheon)
DPS
COM (VIOLET)
NC (PINK)
Ground to Screw
Unused
From
Trim
From
Chassis
E1
To Spade
Connector
(Attached to
Lower Left Screw
of Controller)
JST
(RX)

01/31/18
A7787F 5
Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.S2 WiFi With Rim Exit Device
5
4
8
8
6
9
3
7
11
1
12
10
13
14
15
Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS
(8877/8878 x ET x Lever Design)
6Parts Breakdown for v.S2 With 8877/8878 Rim Exit
2
8
12
14
1a
16

Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/18
6 A7787F
Profile Series v.S2 WiFi With Rim Exit Device
Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS, Continued
(8877/8878 x ET x Lever Design)
ITEM PART NO. DESCRIPTION REQ’D
1 S2-777- 8-HAND-FINISH ’S’ Series ET Trim - With Cylinder 1
S2-778-8-HAND-FINISH ’S’ Series ET Trim - Without cylinder
1a ET Lever Reference 8800 Series Catalog for Available Levers 1
2 68-1397 Outside Escutcheon 1
3 68-1396 Inside Escutcheon 1
4 52-4496 125 kHz Prox Only Bezel Assembly (S1-PA) 1
52-4497 Keypad & 125 kHz Prox Bezel Assembly (S1-PK)
OR
52-4422 13.56 MHz iCLASS Only Bezel Assembly (S2-IA)
52-4423 Keypad & 13.56 MHz Prox Bezel Assembly (S2-IK)
5 52-4425 S2 Controller Assembly (Double Pulse) 1
6 52-3855 Battery Cover Assembly 1
7 01-1212 Security Screw 1
8 52-2525 Profile Screw Pack - Specify Finish (Includes: Fire Stop Plate, Trim Mounting
Screws and Security Allen Wrench)
1
9 52-3968 Chassis Grounding Harness 1
10 52-3893 Door Position Switch 1
11 68-0406 Chassis Cover (Standard) 1
68-1014 Chassis Cover (GL)
12 68-3905 Chassis Cover Screw Pack - Specify Finish (Includes: Chassis Cover Screws) 1
13 68-7255 8800 Chassis Assembly (Standard) 1
68-7256 8800 Chassis Assembly (12-)
68-5836 8800 Chassis Assembly (GL)
68-5837 8800 Chassis Assembly (12-GL)
14 68-3922 Chassis Screw Pack (Includes: Wood and Metal Chassis
Mounting Screws, and Bar Locking Key)
1
15 68-4387 ET Screw pack w/o Cylinder (Includes: ET Mounting Screws) 1
68-4388 ET Screw pack w/ Cylinder (Includes: ET Mounting Screws and Cylinder
Mounting Screws)
1
16 Consult Factory Rim Cylinder 1

01/31/18
A7787F 7
Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.S2 WiFi With Mortise Exit Device
Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS
(8977/8978 x ET x Lever Design)
Parts Breakdown for v.S2 With 8977/8978 Mortise Exit
5
4
8
9
16
3
7
2
10
9
1
13
18
14
15
8
8
6
1a
17
12
12
11

Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/18
8 A7787F
Profile Series v.S2 WiFi With Mortise Exit Device
Parts Breakdown for Profile Series 125 kHz Prox or 13.56 MHz iCLASS, Continued
(8977/8978 x ET x Lever Design)
ITEM PART NO. DESCRIPTION REQ’D
1 S2-777-HAND-FINISH ’S’ Series ET Trim - With Cylinder 1
S2-778-HAND-FINISH ’S’ Series ET Trim - Without cylinder
1a ET Lever Reference 8900 Series Catalog for Available Levers 1
2 68-1397 Outside Escutcheon 1
3 68-1396 Inside Escutcheon 1
4 52-2431 125 kHz Prox Only Bezel Assembly (PA) 1
52-2432 Keypad & 125 kHz Prox Bezel Assembly (PK)
OR
52-4422 13.56 MHz iCLASS Only Bezel Assembly (S2-IA)
52-4423 Keypad & 13.56 MHz Bezel Assembly (S2-IK)
5 52-4425 S2 Controller Assembly (Double Pulse) 1
6 52-3855 Battery Cover Assembly 1
7 01-1212 Security Screw 1
8 52-2525 Profile Screw Pack - Specify Finish (Includes: Fire Stop Plate,
Trim Mounting Screws and Security Allen Wrench)
1
9 52-3968 Chassis Grounding Harness 1
10 52-3893 Door Position Switch 1
11 68-0407 Chassis Cover (Standard) 1
68-3905 Chassis Cover Screw Pack - Specify Finish (Includes: Chassis
Cover Screws)
13 68-7253 8900 Chassis Assembly LHRB 1
68-7254 8900 Chassis Assembly RHRB
14 68-2165 Chassis Screw Pack (Includes: Wood and Metal Chassis
Mounting Screws, and Bar Locking Key)
1
15 68-4387 ET Screw pack w/o Cylinder (Includes: ET Mounting Screws) 1
16 915-Hand-Finish 8900 Lock Body Assembly 1
17 99-2628 Lock body Screw Pack - Specify Finish (Includes: Wood and
Metal Lock body Screws)
1
18 Consult Factory #46 Mortise Cylinder 1

01/31/18
A7787F 9
Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.S2 WiFi With Rim Exit Device
7Installation for Profile Series v.S2 With 8877/8878 Rim Exit Device
For exterior applications, use ET gasket (52-0263) to seal
between ET escutcheon and outside door surface (Fig. 2A).
1A. For wood doors: Route ET wire harness through the
cylinder hole and out the other side.
1B. For metal doors: Route ET wire harness through the
cylinder hole and door and out the 1" diameter cutout.
2. Place ET trim on door.
3. Connector from ET harness connects
to connector from chassis (Fig. 2B)
1 – Prepare Door
A. Verify Hand and Bevel of Door
• This device is non-handed.
• Door should be fitted and hung.
• Verify box label for size of exit device
and function.
B. Door Preparation
If using a mullion, install prior to installing hardware.
Doors should be pre-prepped.
Prep door using the following (see website www.intelligentopenings.com):
• Exit installation instructions A6770
• Field Template A7992 (Wood)
• Door Manufacturer’s Template 4640 (Metal and Wood)
Note: Wood door has additional cutout if installation includes a cylinder.
Inside
Outside
Left Hand
Reverse Bevel
LHRB
Right Hand
Reverse Bevel
RHRB
Fig. 1A
2 - Position Exit Trim (ET)
1
Fig. 2A
Showing Wood Door Template Without Cylinder Hole
ET gasket
(part number
52-0263)
Outside of Door
2
3

Copyright © 2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/18
10 A7787F
Profile Series v.S2 WiFi With Rim Exit Device
1. Route ET harness through wire run channel for wood doors (Fig. 3A)
and through access hole for metal doors (not shown).
Note: Make sure no wires are pinched.
2. Before securing chassis, connect ground wire harness:
a. Spade connector of ground ring terminal wire fits
through the hole (beneath the top screw) in the
chassis and connects to lug on ground
harness (Fig. 3B Detail).
b. Route the ground ring terminal and secure
through the top center hole with the top
1/4-20 x 2-3/8" flat head machine
screw (Fig. 3B Detail).
3. Engage ET spindle in the hub of exit
device chassis.
4. Secure chassis and ET with (2) 1/4-20 x
2-3/8" flat head machine screws.
5. Connect ET harness and connector
from chassis (Fig. 3C).
3 – Secure Inside Trim and Chassis
4
Inside of Door
Fig. 3A
Lug and Spade
Connector
1
3
Ground
Ring
Terminal
Unused
5
Route wires under exits
chassis, and out wire route slot
Fig. 3B Detail
2a
2b
Ground Harness
2
Outside of Door
4
Ground
Ring
Terminal
(Unused)
Fig. 3C
Showing Wood Door Template
With Cylinder Hole