Assa Abloy 1370 User manual

2800 Series1800 Series1370 Series
1360 Series1420 Series1220 Series
MOUNTING INSTRUCTIONS
LOCKWOOD COMMERCIAL DOOR FURNITURE
Product ranges applicable:
P/No. 1220-221 - 0321
1 Set Door Furniture Handing
INSIDE
OUTSIDE
LEFT
HAND
LOCK
RIGHT
HAND
LOCK
INSIDE
OUTSIDE
LEFT
HAND
LOCK
RIGHT
HAND
LOCK
HAND OF DOOR ACCORDING TO ENGLISH PRACTICE
DOOR OPENING OUT
DOOR OPENING IN
B3570 SYNERGY SETTING AND HANDING
A3770 SELECTOR SETTING AND HANDING
SCREW REQUIRED TO SET FOR 3770 SELECTOR
SCREW REQUIRED TO SET HANDING
SET FOR LEFT HAND 3770 SET FOR RIGHT HAND 3770
45°
rotation
45°
rotation
ONE SCREW REQUIRED TO SET HANDING
SET FOR LEFT HAND 3570 SET FOR RIGHT HAND 3570
90°
rotation
90°
rotation
If mounting a plate with a disabled accessible turn, the turn will need to be configured
according to the mortice lock in use.
1. Refer to the images below to identify the mortice lock in use.
2. Position the screws according to the turn setting required.
Selector configurations should allow 45° rotation,
Synergy configurations should rotate to 90°.
Use images below as a guide.
SELECTOR MORTICE LOCK SYNERGY MORTICE LOCK
Stainless
steel plate
Narrow
auxiliary bolt
Wide
auxiliary bolt
Plain case
‘3570 Series’
‘3770 Series’
2 Configuring Disabled Accessible Turn
Stop screws are supplied in an accessory packet
in the box.
For handing of furniture with non-handed levers or
knobs, position the handle by rotating it 180° to suit the
door LH or RH then insert the 4mm stop screw to suit.
Verify the correct handing of furniture on the door required.
Lever should rotate downwards.
1220 & 1420
LH
RH
180°
Stop
screw
1360 & 1370
LH
RH
180°
Stop
screw
1800 & 2800
LH
RH
180°
Stop
screw
Spindle
(supplied with lock
or tubular latch)

Check screw length is correct.
For 1220 & 1420, ensure
screws do not protrude
through outer furniture.
For Round Rose Furniture
Insert fixing screws through
inner retainer rose.
Mount furniture on door
through lock or latch.
Secure furniture by
tightening fixing screws.
For Square Rose Trim Furniture
(1420 only)
If required, fix grub
screw to outer
square rose with allen
key supplied.
For Captive Rose Furniture
(1220 & 1420 only)
For Captive Rose Furniture
levers, loosen and undo
outer rose trim.
Rotate lever 45° and
position rose trim to allow
clear access to fixing screw
holes.
Insert fixing screws.
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 2021
Experience a safer and more open world
Use the appropriate tailbar according to the turn combination mounted.
For single side turn only
P/No. TAILBAR-S1
Suits - 30-40mm doors
P/No. TAILBAR-S2
Suits - 40-50mm doors
1. Insert spring and tailbar into end of
turn knob as above. Push tailbar until
engaged and retained in turn knob.
Refer above for correct tailbar for your
door thickness.
2. Engage tailbar end into turn snib adaptor
as shown.
For privacy configuration (Turn on both sides)
P/No. TAILBAR-E1
Suits 32-45mm doors
1. Insert spring and narrow end
of tailbar into turnknob or
disabled accessible turn until
engaged and retained.
2. Pass tailbar completely through the turn
snib adaptor as shown.
3. Make sure tailbar engages with the turn
escutcheon on the other side of the lock.
3 Door Preparation
4 Mounting Plate Furniture with Turn Configurations
5 Final Assembly
Turn examples:
If required, cut screws to length as indicated. Deburr end of cut screws.
Note: Do not cut with pliers or side-cutters as this is likely to cause thread damage upon
assembly.
Mark hole centres accurately and drill holes required.
Remove lock from mortice and place the template in the correct alignment according to
the backset required.
Cut out template from instruction sheet.
Turn knob Emergency
Turn
Disabled
Accessible turn
THIS IS A COMMON TEMPLATE FOR INSTALLATION OF
LOCKWOOD COMMERCIAL DOOR FURNITURE WHEN
USED WITH THE LOCKWOOD SERIES MORTICE LOCKS.
NOTE: BEFORE DRILLING HOLES CHECK SUITABILITY
WITH LOCKSET AND FURNITURE TO BE FITTED. FOR
ALL OTHER DETAILS REFER TO LOCK MOUNTING
INSTRUCTIONS.
ENSURE LOCK IS REMOVED FROM MORTICE BEFORE
DRILLING HOLES. DO NOT DRILL HOLES RIGHT
THROUGH DOOR TO PREVENT POSSIBLE DAMAGE
TO DOOR FACE.
BORE 2 HOLES 20mm DIA FOR OVAL CYLINDER ONLY BORE HOLE 22mm DIA FOR TURN KNOB ONLY DRILL HOLE 22mm DIA DRILL HOLE 6.5mm DIA PLATE FURNITURE
DRILL HOLE
6.5mm DIA
FOR THROUGH
FIX INSTALLATION
DRILL HOLE
10mm DIA
DIAGONAL
FIX FURNITURE
DRILL HOLE
6.5mm DIA
HORIZONTAL
FIX FURNITURE
TEAR HERETEAR HERE
ALIGN TEMPLATE EDGE WITH BOTTOM OF COVERPLATE RECESS ON DOOR EDGE
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR
127mm BACKSET
89mm BACKSET 60mm BACKSET
CUT OUT
HOLE
CUT OUT
HOLE
LATCH HOLE
POSITION
MORTICE
CENTRELINE
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR
ALIGN TEMPLATE EDGE WITH BOTTOM
OF COVERPLATE RECESS ON DOOR EDGE
127mm BACKSET 89mm BACKSET 60mm BACKSET
BORE 2 HOLES
20mm DIA
FOR OVAL
CYLINDER ONLY
BORE HOLE
22mm DIA
FOR TURN
KNOB ONLY
DRILL HOLE
22mm DIA
DRILL HOLE
6.5mm DIA
PLATE
FURNITURE
DRILL HOLE 6.5mm DIA FOR THROUGH FIX INSTALLATION DRILL HOLE 10mm DIA DIAGONAL FIX FURNITURE DRILL HOLE 6.5mm DIA HORIZONTAL FIX FURNITURE

Check screw length is correct.
For 1220 & 1420, ensure
screws do not protrude
through outer furniture.
For Round Rose Furniture
Insert fixing screws through
inner retainer rose.
Mount furniture on door
through lock or latch.
Secure furniture by
tightening fixing screws.
For Square Rose Trim Furniture
(1420 only)
If required, fix grub
screw to outer
square rose with allen
key supplied.
For Captive Rose Furniture
(1220 & 1420 only)
For Captive Rose Furniture
levers, loosen and undo
outer rose trim.
Rotate lever 45° and
position rose trim to allow
clear access to fixing screw
holes.
Insert fixing screws.
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 2021
Experience a safer and more open world
Use the appropriate tailbar according to the turn combination mounted.
For single side turn only
P/No. TAILBAR-S1
Suits - 30-40mm doors
P/No. TAILBAR-S2
Suits - 40-50mm doors
1. Insert spring and tailbar into end of
turn knob as above. Push tailbar until
engaged and retained in turn knob.
Refer above for correct tailbar for your
door thickness.
2. Engage tailbar end into turn snib adaptor
as shown.
For privacy configuration (Turn on both sides)
P/No. TAILBAR-E1
Suits 32-45mm doors
1. Insert spring and narrow end
of tailbar into turnknob or
disabled accessible turn until
engaged and retained.
2. Pass tailbar completely through the turn
snib adaptor as shown.
3. Make sure tailbar engages with the turn
escutcheon on the other side of the lock.
3 Door Preparation
4 Mounting Plate Furniture with Turn Configurations
5 Final Assembly
Turn examples:
If required, cut screws to length as indicated. Deburr end of cut screws.
Note: Do not cut with pliers or side-cutters as this is likely to cause thread damage upon
assembly.
Mark hole centres accurately and drill holes required.
Remove lock from mortice and place the template in the correct alignment according to
the backset required.
Cut out template from instruction sheet.
Turn knob Emergency
Turn
Disabled
Accessible turn
THIS IS A COMMON TEMPLATE FOR INSTALLATION OF
LOCKWOOD COMMERCIAL DOOR FURNITURE WHEN
USED WITH THE LOCKWOOD SERIES MORTICE LOCKS.
NOTE: BEFORE DRILLING HOLES CHECK SUITABILITY
WITH LOCKSET AND FURNITURE TO BE FITTED. FOR
ALL OTHER DETAILS REFER TO LOCK MOUNTING
INSTRUCTIONS.
ENSURE LOCK IS REMOVED FROM MORTICE BEFORE
DRILLING HOLES. DO NOT DRILL HOLES RIGHT
THROUGH DOOR TO PREVENT POSSIBLE DAMAGE
TO DOOR FACE.
BORE 2 HOLES 20mm DIA FOR OVAL CYLINDER ONLY BORE HOLE 22mm DIA FOR TURN KNOB ONLY DRILL HOLE 22mm DIA DRILL HOLE 6.5mm DIA PLATE FURNITURE
DRILL HOLE
6.5mm DIA
FOR THROUGH
FIX INSTALLATION
DRILL HOLE
10mm DIA
DIAGONAL
FIX FURNITURE
DRILL HOLE
6.5mm DIA
HORIZONTAL
FIX FURNITURE
TEAR HERETEAR HERE
ALIGN TEMPLATE EDGE WITH BOTTOM OF COVERPLATE RECESS ON DOOR EDGE
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR
127mm BACKSET
89mm BACKSET 60mm BACKSET
CUT OUT
HOLE
CUT OUT
HOLE
LATCH HOLE
POSITION
MORTICE
CENTRELINE
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR
ALIGN TEMPLATE EDGE WITH BOTTOM
OF COVERPLATE RECESS ON DOOR EDGE
127mm BACKSET 89mm BACKSET 60mm BACKSET
BORE 2 HOLES
20mm DIA
FOR OVAL
CYLINDER ONLY
BORE HOLE
22mm DIA
FOR TURN
KNOB ONLY
DRILL HOLE
22mm DIA
DRILL HOLE
6.5mm DIA
PLATE
FURNITURE
DRILL HOLE 6.5mm DIA FOR THROUGH FIX INSTALLATION DRILL HOLE 10mm DIA DIAGONAL FIX FURNITURE DRILL HOLE 6.5mm DIA HORIZONTAL FIX FURNITURE