Assa Abloy Norton 9500 Series User manual

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
Multi-Sized 1 thru 6
Non-Hold Open and Hold Open Models
Top Jamb Mount
Pages
9 & 10
Parallel Arm
Pages
7 & 8
Regular Arm
Pages
5 & 6
80-9395-9511-020 REV-2 (08-16)
9500 Series
Installation Instructions
ASSA ABLOY

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
RHR LHR
**NOTE: These forces are for standard templating with bearing type hinges and do not accout for pressure differentials and draft.
IMPORTANT:
BEFORE
INSTALLING:
Page 2
ASSA ABLOY
Size of Door & Door Closer
Type
of
Installation Interior Exterior
In-swinging
Exterior
Out-swinging
Recommended
Closer Size
**Max.
Opening
Force
lbs/f
2 4' "
3 0' "
3 6' "
4 0' "
4 6' "
5 0' "
2 4' "
2 6' "
3 0' "
3 6' "
4 0' "
4 6' "
2 6' "
3 0' "
3 6' "
4 0' "
2 6' "
3 0' "
3 6' "
4 0' "
3 0' "
3 6' "
4 0' "
4 6' "
1
2
3
4
5
6
8
14
16
22
24
26
8
14
16
22
24
26
1
2
3
4
5
6
Regular &
Top Jamb
Parallel
Arm
The Americans with Disabilities Act (ADA) requires that doors having door closers
Ÿ
have an opening force not to exceed 5 lbf. Use standard templating for regular arm
and parallel arm applications. Jamb mounted applications use the template for 140°
door opening to achieve the required opening force.
The door closer's power size adjustment feature may require adjustment to its
Ÿ
lowest setting to comply with ADA opening force guidelines.
An auxiliary door stop, by others, is strongly recommended to avoid damage to the
Ÿ
door closer and adjacent property.
Doors should be hung on ball bearing or anti-friction hinges/pivots.
Ÿ
Door closer must not be installed on the exterior of a door in an exterior wall of a
Ÿ
building.
ADA compliant closers
Ÿ
An improperly installed or incorrectly adjusted door closer may cause property
Ÿ
damage or personal injury; and will void product warranty.
To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.
Ÿ
Door closers must be securely fastened to a properly reinforced door and frame
Ÿ
with fasteners provided.
Door closers with the HOLD OPEN ARM option are not permitted to be
Ÿ
installed in fire door assemblies.

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
Components: Figure 1
Plastic Cover
(Standard)
Main Arm
Arm Bracket
Adjusting Rod
Threaded
Adjusting Rod
Screw Pack
Closer Mounting
Bracket
Closer
Optional Hold Open
Arm
For Parallel Arm Only
Adapter Plate Bracket
Page 3
ASSA ABLOY

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
9/32” (7 mm);
3/8” (9.5 mm) dia. x
3/8” (9.5 mm) deep on
door opposite to closer
Standard
Optional
Through-bolts and
grommet-nuts All
Preparation for Fasteners Figure 2
Door or Frame
Fasteners Drill-Sizes
#12-14 Self-Drilling Screw Wood
(see Note) 1/8” (3.2 mm)
1/4” - 20 machine screw Metal Drill: #7 (0.201” dia.)
Tap: 1/4” - 20
Sleeve nuts and bolts
1-9/32" (33) = 1-3/8" (35) Door Thk.
1-21/32 (42) = 1-3/4" (44) & Over Dr. Thk.
Hollow
Metal
9/32” (7 mm) through;
3/8” (9.5 mm) door face
opposite to closer
Aluminum
or Wood 3/8” (9.5 mm) through
Aluminum
or Metal No drill required
Note: Wood doors/frames: drill 1/8" (3.2) pilot hole when using Self-Drilling Screws.
Always consult door/frame manufacturer for fastener compatibility with the material of their door/frame.
Page 4
ASSA ABLOY
It is recommended that the door, on which the door closer will be installed, be hung on ball bearing hinges.
•
Door must swing freely.
A separate door stop, supplied by others, is recommended to prevent damage to the door closer, closer arm;
•
or to the door, frame or adjacent walls.
Door and Frame must be properly reinforced, or use of special fasteners employed, to prevent the mounting
•
screws from pulling out.
All dimensions are given in inches with corresponding metric dimensions (millimeters) in parentheses.
•

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
If top rail is 3 (76) or greater, use the template for the Closer Mounting Bracket provided."
If top rail is 1-3/4 (45) to 2-15/16 (75), use 9586 Drop Plate Dimensions denoted by ."
2-1/4
(57)
*10-5/8
(270)
C
L
HINGE OR
PIVOT
*5-5/8
(143)
FRAME LINE
ARM BRACKET
MOUNTING BRACKET
TOP OF DOOR
10
(254)
1
(25)
3/4
(19)
1/2
(13)
To obtain extra closing force add 3 (76) to dimensions marked."
This will limit degree of door opening to 110°.
*
*5-1/4
(133)
3
(76)
4-3/4
(121)
3
(76)
1-5/8
(41) 3/8
(10)
DROP PLATE
Mounting Holes (4)
Regular Arm Template
Page 5
ASSA ABLOY
NOTES:
• Check hand of door, see page 2.
• Right Hand Application Shown. Left Hand Opposite.
• Dimensions given in inches (mm). Do Not Scale Drawing.
• Closer must be installed in a true horizontal plane to ensure proper closer performance.
• Door opening (up to 180°) is dependent upon door, frame, wall and hinge/pivot conditions permitting.
• Minimum clearance required over door:
Non-Hold Open: 1-1/2" (39)
Hold Open: 1-11/16" (43)

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
• Select angle of opening and use dimensions shown in
template and chart to locate 4 holes on door for Closer
Mounting Bracket (or 4 holes for optional drop plate)
and 2 holes on frame face for arm bracket. For
applications that are different from above, a separate
template will be supplied for door and frame preparation.
• Prepare door and frame for fasteners using "Preparation
for Fasteners" chart, Figure 2, Page 4.
• Fasten Closer Mounting Bracket to door. Fasten optional
drop plate to door, only if it is required for the door
conditions.
• Install closer body with tube end away from hinge, with
valves:
Down for Left Hand door
UP for Right Hand door.
• Fasten arm bracket to frame. For standard non-hold open
mounting, position with pivot point away from hinge. For
additional 15% closing force, reposition arm mounting
bracket so that pivot point is toward hinge. For hold open
mounting, position so that dial screw is on UNDERSIDE of
bracket.
• Attach main arm to closer.
For non-hold open mounting, main arm projects straight
out at 90° angle to door. Install and tighten arm screw &
washer assembly.
Main Arm
5/16 Hex Head
Screw & Washer Assembly
For hold open mounting, main arm projects straight out at
90° angle to door. Remove arm screw and washer from
elbow joint and disassemble arm. Thread the rod into the
arm bracket as shown below. Install and tighten arm screw
& washer.
• Preload and adjust arm.
NON-HOLD OPEN ARM ONLY:
Open door and slide arm rod into arm loop. Close door,
swing arms so adjusting arm is 90° to frame. With 7/16"
wrench INSTALL and TIGHTEN SCREW SECURELY.
HOLD OPEN ARM ONLY:
While door is closed, adjust the threaded arm in the arm
bracket until the bearing fits back onto the elbow joint on
the main arm at 90° as shown below. RE-INSTALL AND
TIGHTEN SCREW SECURELY.
• Make closer adjustments using information on page 11,
then install closer cover.
HOLD OPEN ARM
Main Arm
Threaded
Rod
Arm
Bracket
DIAL
SCREW
HOLD OPEN
Standard:Pivot away from hinge
+15% Power: Pivot toward hinge
NON-HOLD OPEN
Arm Tube
Arm Rod
Screw 90°
Threaded
Arm
Screw 90°
Main Arm
HOLD OPEN ARM
NON-HOLD OPEN ARM
Regular Arm Installation Sequence
Page 6
ASSA ABLOY

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
To obtain extra closing force add 3" (77) to dimensions marked.
This will limit degree of door opening to 110°.
*
HINGE
OR
PIVOT
C
L
*3-1/2
(89)
FRAME STOP PA ADAPTER
PLATE
MOUNTING
BRACKET
TOP OF DOOR
10
(254)
1
(25)
3-1/16
(78)
C
L
5/8
(16)
DOOR
FRAME STOP
2-3/4
(70)
5/8
(16)
1-1/2
(38)
1/4
(6)
*8-1/8
(206)
1/2
(13) *3-1/8
(79)
3
(76)
4-3/4
(121)
3
(76)
3/8
(10)
If top rail is 5-1/4 (133) or greater, use the template for the Closer Mounting Bracket provided.
If top rail is 1-3/4 (44) to 5-1/8 (130), use 9588 Drop Plate Dimensions denoted by .
Parallel Arm Template
NOTES:
• Check hand of door, see page 2.
• Right Hand Application Shown. Left Hand Opposite.
• Dimensions given in inches (mm). Do Not Scale Drawing.
• Closer must be installed mounted level to ensure proper closer performance.
• Door opening (up to 180°) is dependent upon door, frame, wall and hinge/pivot conditions permitting.
5/8
(16)
REF.
DOOR
FRAME
ADAPTER
PLATE
SPACER
BLOCK
(When
required)
Page 7
ASSA ABLOY

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
• Connect and position arms. Open door and slide arm rod
into arm loop. Close door, swing arms so that they form a
“V” position. With 7/16 wrench, INSTALL AND TIGHTEN "
SCREW SECURELY. For hold open mounting, Remove
main arm screw from elbow joint and disassemble arm.
Thread the rod into the arm bracket as shown below.
While door is closed, adjust the threaded arm in the arm
bracket until the bearing fits back onto the elbow joint on
the main arm and forms a "V" as shown below. RE-
INSTALL AND TIGHTEN SCREW SECURELY.
R
O
O
D
F
O
E
G
D
E
E
G
N
I
H
M
O
R
F
Y
A
W
A
5/16 Hex Head
Screw & Washer
Assembly
Rotate 45°
Closer Tube
Fig. 1
Fig. 2
Square
position-
At rest
Diamond
position-
Rotated 45°
• Select angle of opening and use dimensions shown in
template to locate 4 holes on door for Closer Mounting
Bracket (or 4 holes for optional drop plate) and 2 holes
on jamb for adapter plate bracket. For applications that are
different from above, a separate template will be supplied
for door and frame preparation.
• Prepare door and frame for fasteners using "Preparation
for Fasteners" chart, Figure 2, Page 4.
• Fasten Closer Mounting Bracket to door.
Fasten optional drop plate to door, only if it
is required for the door conditions.
• Fasten adapter plate bracket on jamb.
• Install closer body with tube end toward
hinge, with valves:
Down for Left Hand door
UP for Right Hand door.
• Mount arm bracket onto adapter plate bracket. For non-
hold open mounting, position with pivot point away from
hinge. For hold open mounting, position so that dial screw
is facing DOWN.
• Attach main arm to closer. Using hex wrench provided,
turn closing speed and latching speed valves clockwise
until completely closed. DO NOT OVER TIGHTEN. Using
wrench, turn under side of spindle 45° toward the closer
tube until it reaches the diamond position (fig.
2 below). Immediately place arm on spindle
so that it is parallel to the closer body. Install
and tighten arm screw and washer assembly.
Reopen valves.
Arm Tube
Arm Rod
Screw
Threaded
Arm Arm Bracket
Main Arm
HOLD OPEN ONLY
Dial
Screw
HOLD OPEN
Pivot away from hinge
NON-HOLD OPEN
• Make closer adjustments using information on page 11,
then install closer cover.
• Power adjustment. To increase the power of the closer, re-
adjust the arm so it is nearer the door. To decrease power,
re-adjust the arm so it is farther away from the door and
then secure screw in arm loop (non-hold open) or elbow
joint (hold open).
3
(76)
MAX.
MINIMUM POWER
1-1/2
(38) MIN.
MAXIMUM POWER
Page 8
Parallel Arm Installation Sequence
ASSA ABLOY

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
NARROW
E
2-3/8
(60)
1-3/4
(45)
C
1-1/2
(38)
1-7/8
(48)
D
3/4
(19)
3/8
(10)
F
4
(102)
3-1/2
(89)
STANDARD
HEADER
WIDTH
B
14
(356)
HINGE
CONDITION
5-1/8
(130)
12-1/2
(318)
5-1/8
(130)
12-3/8
(314)
3-3/8
(86)
10-1/2
(267)
Butts, Offset
Pivots, and
Swing Clear
Hinges
110°
140°
180°
140° CENTER
HUNG
*
Dimensions “A” and “B” are taken from
centerline of hinge as shown and apply to
pivot point of swing clear hinges. Offset
and center hung pivots.
*Must be single acting door.
A
6-7/8
(175)
OPENING
MAXIMUM
NOTES:
• Check hand of door, see page 2.
• Right Hand Application Shown. Left Hand Opposite.
• Dimensions given in inches (mm). Do Not Scale Drawing.
• Closer must be installed mounted level to ensure proper closer performance.
• All degrees of door opening are dependent upon door, frame, wall and hinge/pivot conditions permitting.
FMIN.
A
FRAME STOP
ARM BRACKET
MOUNTING BRACKET
TOP OF DOOR
10
(254)
1
(25)
D
2-1/4
(57) B
C
CEILING LINE
EMIN.
TOP OF FRAME
DO NOT USE THIS TEMPLATE WITH A 9857 DROP PLATE.
Page 9
Top Jamb Template
ASSA ABLOY

80-9395-9511-020 REV-2 (08-16)
Norton is a brand associated with Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2016, Yale Security Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of Yale Security Inc. is prohibited.
• Select angle of opening and use dimensions shown in
template and chart to locate 4 holes on frame for
Closer Mounting Bracket and 2 holes on door for
adaptor plate. For applications that are different from
above, a separate template will be supplied for door and
frame preparation.
• Prepare door and frame for fasteners using "Preparation
for Fasteners" chart, Figure 2, Page 4.
• Fasten Closer Mounting Bracket to jamb.
• Install closer body with tube end away from hinge, with
valves:
Up for Left Hand door
Down for Right Hand door.
• Fasten arm bracket to door. For standard non-hold open
mounting, position with pivot point away from hinge. For
additional 15% closing force, reposition arm mounting
bracket so that pivot point is toward hinge. For hold open
mounting, position so that dial screw is facing DOWN.
• Attach main arm to closer.
For non-hold open mounting, main arm projects straight
out at 90° angle to door. Install and tighten arm screw &
washer assembly.
DIAL
SCREW
HOLD OPEN
Standard:Pivot away from hinge
+15% Power: Pivot toward hinge
NON-HOLD OPEN
For hold open mounting, main arm projects straight out at
90° angle to door. Remove arm screw and washer from
elbow joint and disassemble arm. Thread the rod into the
arm bracket as shown below. Install and tighten arm screw
& washer.
• Preload and adjust arm.
NON-HOLD OPEN ARM ONLY:
Open door and slide arm rod into arm loop. Close door,
swing arms so adjusting arm is 90° to frame. With 7/16"
wrench INSTALL and TIGHTEN SCREW SECURELY.
HOLD OPEN ARM ONLY:
While door is closed, adjust the threaded arm in the arm
bracket until the bearing fits back onto the elbow joint on
the main arm at 90° as shown below. RE-INSTALL AND
TIGHTEN SCREW SECURELY.
90°
Arm
Bracket
Threaded
Arm
Screw
Main Arm
Arm Rod
Screw
Arm
Loop
90°
• Make closer adjustments using information on page 11,
then install closer cover.
Main Arm
5/16 Hex Head
Screw & Washer
Assembly
Main Arm
Threaded
Rod
Arm
Bracket
5/16 Hex Head
Screw & Washer
Assembly
Page 10
Top Jamb Installation Sequence
ASSA ABLOY