Assa Abloy Corbin Russwin PED5600 Series User manual

Installation Instructions
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in damage
to the product and void the factory
warranty.
WARNING
FM580 1/23
Mortise Lock Type Exit Device
PED5600 & PED5600 A Series
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

2
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Screw Chart
DESCRIPTION
TOTAL QTY
SUPPLIED
WHERE USED
#10-24 X 3/4" FLAT HEAD
MACHINE SCREW
4
(4) CHASSIS
CORNER MOUNTING HOLES
(METAL DOOR)
#10 X 1-1/4" FLAT HEAD
WOOD SCREW
4
(4) CHASSIS
CORNER MOUNTING HOLES
(WOOD DOOR)
#10-24 X 3/4" ROUND HEAD
MACHINE SCREW
2
(2) REAR MOUNTING PLATE
(METAL DOOR)
#10 X 1-1/4" ROUND HEAD
WOOD SCREW
2
(2) REAR MOUNTING PLATE
(WOOD DOOR)
#12-24 X 1/2" FLAT HEAD
MACHINE SCREW
4
(2) 908 STRIKE
(METAL FRAME)
(2) MORTISE LOCK BODY
(METAL DOOR)
#12 X 1" FLAT HEAD
WOOD SCREW
4
(2) 908 STRIKE
(WOOD FRAME)
(2) MORTISE LOCK BODY
(WOOD DOOR)
#8-32 X 5/16" W/ #6 OVAL HEAD
MACHINE SCREW
4
(2) CHASSIS COVER
FRAME SIDE
(2) END CAP
#8-32 X 5/8" W/ #6 OVAL HEAD
MACHINE SCREW
2(2) CHASSIS COVER
RAIL SIDE
1/4"-20 X 2-3/8" KNURLED FLAT HEAD
MACHINE SCREW
2
(2) EXIT TRIM
(IF USED)

3
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
PED5600 & PED5600 A Exploded View
Rail Cutting Guide (Provided)
Tools Needed
Support Block (Provided)
M52-Cylinder Lockdown
(Exploded View for Clarity)
Mortise
Cover
Arm
Push Rail Assembly
Mounting Plate
End Cap
Vertical reference
line (C Chassis)
INSIDE
REVERSE
LEFT HAND
BEVEL
RIGHT HAND
REVERSE
BEVEL
OUTSIDE
THIS EXIT DEVICE IS HANDED
CHECK HAND OF DEVICE AGAINST APPLICATION
Left hand reverse bevel
illustrated
Chassis
“Lock Down Key”
To operate: Depress pushrail; insert hex
key, and turn counter clockwise.
Attention:
Not available with Fire Rated PED5600 A
Exit Devices.

4
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
1. Check hand of door. This device is handed and non-reversible.
2. Install mullion, if used.
3. Fit and hang door.
4. For wood doors, use wood screws and prep accordingly.
The surface of the door where the exit device is to be applied must be flush. Clear away
any raised projections to allow exit device to rest on the flat surface of the door. If shim
kit is required, contact your distributor.
Note: Please refer to trim and other installation instructions provided in the box.
Product Overview
Before installation:

5
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
12
34
Obtain dimension to finished floor from template
or from relationship to strike prep. Mark vertical
centerline by measuring 2 3/4"off of the door edge.
Place template against frame, centered on the
line marked in Step 1. Mark and prepare door
according to template.
Install the strike to door frame using flat head
#12-24 x 1/2"long screws.
Install the mortise lock body using flat head
#12-24 x 1/2"long screws.

6
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
While maintaining chassis position set in Step 6,
mark chassis mounting holes.
Drill and tap #10-24 holes in previously
marked chassis locations.
78
56
Insert chassis lever into door prep opening
underneath the mortise lock lever.
A. Depress the chassis lift arm.
B. Slide chassis upwards until mortise latch bolt is
fully retracted (C).
A
B
C

7
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Install chassis to the door using #10-24
flathead screws supplied. Do not fully tighten
screws.
9

8
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
If the rail doesn’t need to be cut, continue to page 9, step 10.
If the rail must be cut, follow these steps on page 7 and 8:
Refer to the individual exit device installation instructions for rail cutting requirements / restrictions.
Instructions will vary based on device type and options.
Do not cut closer than 1-5/8"from
the the front edge of the rail insert.
• Determine cut off dimension “X” by subtracting 2-7/8"
from dimension “Y”. Mark cut off point on mounting
rail. (See below.)
Verticle reference line (C of chassis)
L
2-7/8"
min.
For doors with stile rail, the stile must overlap by 5/16"min.
X
Y
A. Ensure there isn’t a gap between the insert
and the dogging slope, and the carrier is
flush with the mount.
B. Mark rail at the required cut length.
Insert
Dogging
slope Cut line
Mount
Carrier
Information for Cutting Rails
Rail Sizes Door Widths
Standard Minimum
32" 24"
36" 33"
42" 37"
48" 43"
W032
W042
W048
W036 (Std.)
Rail cutting guide

9
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
CUT LINE
F. Using a hack saw with a new blade or a chop
saw with a metal cutting blade, cut the rail,
ensuring that the blade stays pressed against
the rail cutting guide.
G. Deburr and smooth all cut edges with a file.
D. Wrap the rail and insert in masking tape, as
shown.
E. Place the rail cutting guide over the masking tape and align it with the cut line. Clamp the cut guide to the rail
using a C-clamp.
C. Ensure plastic insert support is installed under the
cut line.
Cut line
Rail Cutting Guide
Rail cutting guide, continued.

10
PED5600 & PED5600 A Series
Installation Instructions
Mortise Lock Type Exit Device
FM580 1/23
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Depress chassis lift arm. Slide rail assembly
onto chassis.
10
Ensure rail carrier tabs are aligned with
chassis.
11
Fully tighten chassis screws.
12
Insert the end cap bracket into the rail assembly.
13