Assa Abloy Corbin Russwin PED5800 Series User manual

Installation Instructions
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in damage
to the product and void the factory
warranty.
WARNING
PED5800 Series (A MD, MD, and AD)
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23

2
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
SCREW
TOTAL QTY
SUPPLIED
WHERE USED
#10-24 X 3/4" FLAT HEAD
MACHINE SCREW
4
(4) CHASSIS
CORNER MOUNTING HOLES
#10-24 X 3/4" ROUND HEAD
MACHINE SCREW
2 (2) REAR MOUNTING PLATE
#10-24 X 3/8" FILLISTER HEAD
MACHINE SCREW
1
(1) INNER CHASSIS
TOP MOUNTING HOLE
#10-24 X 3/8" OVAL HEAD
MACHINE SCREW
4
(2) TOP CASE
(2) BOTTOM PLATE (IF AD)
1/4"-20 X 1/2" FLAT HEAD
MACHINE SCREW
2(2) BOTTOM PLATE
(MD OR FIRE RATED)
#10-24 X 1/2" U'CUT FLAT HEAD
MACHINE SCREW
5
(1) INNER CHASSIS
BOTTOM MOUNTING HOLE
(2) 640 OR 650 STRIKE, TOP
(METAL FRAME)
(2) 640 OR 650 STRIKE, BOTTOM
(METAL FRAME)
#10 X 1-1/4 FLAT HEAD
WOOD SCREW
2
(2) 650 STRIKE, TOP
(WOOD FRAME)
(2) 650 STRIKE, BOTTOM
(WOOD FRAME)
1/4"-20 X 2" FLAT HEAD
MACHINE SCREW W/ANCHOR
2
(2) 606 BOTTOM STRIKE
(FIRE RATED)
#8-32 X 5/16" W/ #6 OVAL HEAD
MACHINE SCREW
4
(2) CHASSIS COVER
FRAME SIDE
(2) END CAP
#8-32 X 5/8" W/ #6 OVAL HEAD
MACHINE SCREW
2(2) CHASSIS COVER
RAIL SIDE
1/4"-20 X 2-3/8" KNURLED FLAT HEAD
MACHINE SCREW
2
(2) EXIT TRIM
(IF USED)
Screw Chart
AA
EE
HH
DD
FF
GG

3
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
Rail Cutting Guide (Provided)
Support Block (Provided)
Equipment Needed
Tools
Before installation:
1. Fit and hang door.
2. Check the box’s label for the size of the exit device.
The surface of the door where the exit device is to be applied must be flush. Clear away
any raised projections to allow exit device to rest on the flat surface of the door. If shim
kit is required, contact your distributor.
Note: Please refer to trim and other installation instructions provided in the box.
Strike Packs
Strike Pack for AD-PE8400
640 TOP AND BOTTOM STRIKE
#10 X 1/2"
PHILLIPS FLAT HEAD
MACHINE SCREW
(4 I N P A C K F O R T O P
AND BOTTOM S TRIKE )
Strike Pack for MD-PE8400 Strike Pack for 12-MD-PE8400
PED5800 MD
PED5800 AD PED5800 A M55

4
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
Template PE5800 AD, PE5800 AD M55, PED5800 MD, PED5800 MD M55,
PED5800 A MD, PED5800 A MD M55
Omit holes for M55 AD version and all MD versions.
.395
.300
.150
10-24 UNC - 2B
ONLY FOR RHRB
THRESHOLD IF USED
MUST LEAVE A MINIMUM
.350
ONLY FOR LHRB
ONLY FOR RHRB
.187
.187
.811 2.388
AND DOUBLE DOORS)
CENTER LINE OF RAIL
ONLY FOR RHRB
FOR LHRB, SEE DETAIL A
NOTES:
DOOR PREPARATION SHOWN FOR INSIDE DOOR ONLY. 1.
IF OUTSIDE PULL AND/OR OUTSIDE CONTROL IS USED, SEE APPROPRIATE DOOR TEMPLATE FOR OUTSIDE DOOR PREP. 2.
3.
4.
WE RECOMENDED THAT ALL TAPPED HOLES BE DRILLED AND TAPPED IN FIELD. 5.
TOLERANCE ALL FRACTIONAL DIMENSIONS
6.
7.
8.
9.
OPENING FOR
INSERTING DEVICE
C
L
OF RODS
MINIMUM CLEAR
OPENING FOR
INSERTING DEVICE
TOP OF DOOR
.811
.350
2.388
DETAIL A
SCALE 1 : 1
FEATURE FOR LHRB
For MD-bottom plate prep.
May be omitted for M55 MD
versions.
1/2 "
5/8 "
1/4-20 Tapped Holes (2 Places)
2-3/4 "
3/8 "

5
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
*Note: The PED5800 AD M55, PED5800 MD M55 & the PED5800 A MD M55 do not have a bottom rod assembly.
M52 Cylinder Lockdown
(Exploded View For Clarity)
Slide mounting rail insert with M52
cylinder dogging into mounting rail.
Exploded View
Rod silencer
End cap
INSIDE
LEFT HAND
REVERSE
BEVEL
RIGHT HAND
REVERSE
BEVEL
THIS EXIT DEVICE IS HANDED
CHECK HAND OF DEVICE AGAINST APPLICATION
OUTSIDE
Push rail assembly
Center case chassis
Chassis cover
Top Chassis
Top Bolt
Chassis
*Bottom rod assembly
Mounting Plate

6
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
Remove door from frame, and prepare the door per template.
1

7
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
2
Screw top bolt and rod assembly and bottom bolt
and rod assembly into the inner chassis.
*Bottom bolt rod and assembly will not be used with
M55 devices.
Top bolt and rod assembly
*Bottom bolt and rod assembly

8
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
3
Feed rod and inner chassis assembly into the door. Ensure teeth face down and top bolt teeth are opposite
the inside door prep.
Top bolt teeth

9
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
FF
4
Attach inner case chassis to the door with (1) #10-24 x 1/2” flat head screw (HH) and secure with (1) #10-
24 x 3/8 fillister head machine screw (FF). If PT Series trim is being used, it must be installed at this point.
See trim instructions for details.
#10-24 x 3/8"
Fillister head screw
#10-24 x 1/2"
Flat head screw
5
Locate chassis on the fillister head screw (FF). Attach to the door with (4) #10-24 x 3/4 flat head screws (AA).
Do not fully tighten screws.
AA
HH

10
PED5800 Series (A MD, MD, AD)
Installation Instructions
Concealed Vertical Rod Exit Devices
Copyright © 2023 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in
part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
1-800-543-3658 • [e-mail]
FM581 1/23
6
Adjusting the top bolt and rod assembly
• 1/8” gap or less between door top and frame: Rotate bolt to make it even with the top of the door.
• 1/8” gap or greater: Bolt must extend above the door, equal to the gap, minus 1/8”.
Adjusting the bottom bolt and rod assembly (Not needed for M55 exit devices)
• 1/8” gap or less between door bottom and high point: Rotate bolt to make it even with the top of the
door.
• 1/8” gap or greater: Bolt must extend below the door, equal to the gap, minus 1/8”.
Note: Rod must be retracted while adjusting bolt projection. Depress chassis lift arm to retract top bolt
and rod assembly.