Assa Abloy SARGENT 1431 User manual

1431 DOOR CLOSER WITH P10/PH10 ARM
INSTALLATION INSTRUCTIONS
CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY
MAY RESULT IN INJURY OR DAMAGE.
FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477
1LOCATE AND MARK HOLES USING FULL SIZE TEMPLATE OR
MEASURE AS SHOWN BELOW
RIGHT HAND SHOWN, LEFT HAND OPPOSITE.
PULL SIDE PULL SIDE
PUSH SIDE PUSH SIDE
LEFT HAND DOOR RIGHT HAND DOOR
1431 CLOSER AND P10 ARM ARE NON-HANDED
ONLY THE PH10 ARM IS HANDED
ATTACH FOOT BRACKET TO DOOR STOP.
3
4
ATTACH DOOR CLOSER TO DOOR WITH SPRING POWER NUT
TOWARD HINGE.
PRE-DRILL 3/32" HOLES FOR SELF TAPPING
SCREWS OR USE #16 DRILL (DIA.177) AND
TAP #12-24 FOR MACHINE SCREWS
A7387D 1
* NOTE: FOR MAXIMUM POWER, INSTALL FOR 90° OPENING.
ALTERNATE: PREASSEMBLE ARM PRIOR TO
ATTACHING TO STOP
4A
+
or
USE FIFTH HOLE SPACER
WHEN REQUIRED
IMPORTANT: USE A MINIMUM OF 5 SCREWS
HAND
(PH10 ONLY)
2
Copyright ©2006-2008 SARGENT Manufacturing. All rights reserved.
Reproduction in whole or in part without the express written
permission of SARGENT Manufacturing is prohibited.
A7387C 1/30/08 3:17 PM Page 1

ALTERNATE METHOD FOR ATTACHING ARM:
A. PREASSEMBLE ARM TO FOOT BRACKET
B. MOUNT ARM TO CLOSER AS SHOWN IN STEP 4
C
B
A
ACCESSORIES
5ATTACH ARM TO CLOSER
*A. ROTATE BOTTOM SPINDLE WITH WRENCH
B. INSTALL MAIN ARM WITH INDEX MARK
POSITIONED AS SHOWN BELOW
C. SECURE WITH SCREW AND WASHER
*WARNING: IF NOT PROPERLY INDEXED, DOOR
CLOSER WILL NOT FUNCTION PROPERLY.
6
!! !!
A
B
C
6A
2A7387D
125 VF BRACKET FOR FLUSH FRAME
AND DOOR CONDITION
OPTIONAL: USE MORTISE NUTS (TB)
WHEN THROUGH-BOLTING IS REQUIRED
SEE PAGE 4
FOR
TEMPLATING
DIMENSIONS
FLUSH
FRAME
DOOR
125 V BRACKET FOR NARROW FRAME
CONDITION
1431-D DROP PLATE USED WITH NARROW TOP RAILS
D
O
O
R
1431-D DROP PLATE
581-2 SPACER USED
WITH BLADE STOPS
MAIN ARM
A. OPEN DOOR AND
INSTALL PIVOT AS
SHOWN
B. USE SCREW TO SECURE
PIVOT AND ARMS AS SHOWN
A
B
Copyright ©2006-2008 SARGENT Manufacturing. All rights reserved.
Reproduction in whole or in part without the express written
permission of SARGENT Manufacturing is prohibited.
A7387C 1/30/08 3:17 PM Page 2

B
Door Closer Cycle
Opening
cycle
DOOR WIDTH 1431 DOOR CLOSER
(INCHES)
24-30 TURN nut 1-3
30-36 FACTORY SET
36-42 TURN nut 1-3
42-48 TURN nut 7-9
FINAL ADJUSTMENT AND REGULATING PROCEDURES
7
8ADJUST CLOSING POWER TO THE MINIMUM REQUIRED TO
RELIABLY CLOSE AND LATCH DOOR
9INSTALL COVER AS SHOWN
3
SPRING POWER
ADJUSTMENT GUIDELINES
SHORT SCREW
GAP
PLASTIC SPACER
AND LONG SCREW
MOVE
INSERT AS
NEEDED
10
SLIGHT TIGHTENING OR
LOOSENING OF HOLD OPEN
NUT CHANGES HOLDING
POSITION OF DOOR
NOTE: ALWAYS USE A DOOR
STOP TO STOP DOOR TO
PROTECT WALL AND TRIM
ADJUSTMENT OF HOLD OPEN ARM
(PH10 ARM ONLY)
1-3/8" WRENCH
A7387D
– Adjust Door speed, and Latching speed valves to achieve the desired closing time.
Recommend 6 seconds minimum from 90° to the closed position.
– If Backcheck is required, adjust valve to achieve a slight cushioning effect.
Auxiliary stop required.
– If closer is equipped with Delayed Action,
regulate valve to achieve the desired delay.
Latching speed range
Closing
speed range
Backcheck range
Spring Power
Adjustment
Backcheck
Closing speed
Latching speed
Delayed
action
(Optional)
SLOW
DOWN
SPEED
UP
Delayed
action range
Use 1/8" hex wrench to
adjust valves
– If door is hard to open, decrease power
slightly
– If door does not latch, increase power
as required
– Use the chart as a starting point
– Doors adjusted with high closing power
to overcome strong draft conditions may
exceed ADA standards.
Copyright ©2006-2008 SARGENT Manufacturing. All rights reserved.
Reproduction in whole or in part without the express written
permission of SARGENT Manufacturing is prohibited.
A7387C 1/30/08 3:17 PM Page 3

4A7387D
Copyright ©2006-2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
A7387C 1/30/08 3:17 PM Page 4