Assa Abloy Corbin Russwin DC3200 Series User manual

80-9330-3004-152 04/18
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
DC3200 Series
Important
• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void
product warranty.
• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.
• Door closers must be securely fastened to a properly reinforced door and frame with fasteners provided.
• Door closers with a HOLD OPEN ARM are not permitted to be installed in fire door assemblies.
• Door and frame must be specifically templated for 85°, 90°, 95°, 100°, 105° orb 110° door swing.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
A10 Heavy Duty Non-Hold Open Regular Arm

2
80-9330-3004-152 04/18
DC3200 Series Closer
Installation Instructions
A10 Heavy Duty Non-Hold Open Regular Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
**NOTE: These forces are for standard templating with bearing type
hinges and do not account for pressure differentials and draft.
Size of Door & Door Closer
Type of
Installation Interior Exterior In-swinging
Recommended
Closer Size
**Max. Opening
Force lbs/f
Regular Arm
2' 4" - 1 8
3' 0" - 2 14
3' 6" 2' 6" 3 16
4' 0" 3' 0" 4 22
4' 6" 3' 6" 5 24
5' 0" 4' 0" 6 26
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
RHR LHR
1 Introduction
L
3/8
(10)
1/4-20 THREAD
Drill thru 9/32 (7.1) Enlarge to
3/8
(9.5) Dia. This Side Only
(4 Places)
DOOR
THICKNESS
SEX NUT
LENGTH “L”
1-3/8" (35mm)
1--3/4" (44mm)
&OVER
1-9/32" (33mm)
1-21/32" (42mm)
MOUNTINGSCREW SPECIFICATIONS
ARM AND CLOSER BRACKET
}
or{Option M54:
Sex nuts, furnished
when ordered
1/4-20 oval head machine
screw or 1/4-14 self-drilling
screw Type BSD. 3/16 (4.8)
diameter pilot hole required
forWood Applications.
L
3/8
(10)
1/4-20 THREAD
Drill thru 9/32 (7.1) Enlarge to
3/8 (9.5) Dia. This Side Only
(4 Places)
DOOR
THICKNESS
SEX NUT
LENGTH “L”
1-3/8" (35mm)
1--3/4" (44mm)
&OVER
1-9/32" (33mm)
1-21/32" (42mm)
MOUNTINGSCREW SPECIFICATIONS
ARM AND CLOSER BRACKET
}
or{Option M54:
Sex nuts,
furnished
when ordered
1/4-20 oval head machine
screw or 1/4-14 self-drilling
screw Type BSD. 3/16 (4.8)
diameter pilot hole required
forWood Applications.
Figure 1
BEFORE INSTALLING:
• The Americans with Disabilities Act (ADA) requires that doors having door closers have an opening force not to
exceed 5 lbf. for interior doors, 8.5 lbf exterior doors.
• The door closer’s power size adjustment feature may require adjustment to its lowest setting to comply with ADA
opening force guidelines.
• ADA compliant closer: DC3200.

3
80-9330-3004-152 04/18
DC3200 Series Closer
A10 Heavy Duty Non-Hold Open Regular Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
1. Template
Mark and prepare door and jamb (for closer
bracket and arm bracket).
For Vertical Dimensions use “Mounting
Dimensions Chart” (Figure 2)
NOTES:
• Check hand of door. (Figure 1)
• Right Hand Application Shown,
Left Hand Opposite
• Dimensions given in inches (mm).
Do Not Scale Drawing.
• Closer must be installed in a true
horizontal plane to ensure proper closer
performance.
• Door opening (up to 180°) is dependent
upon door, frame, wall and hinge/pivot
conditions permitting.
• Maximum Hinge Side Reveal 1/8" (3mm).
Figure 2
CLOSER BRA
CKET
B
A
2-1/4
(57.2)
*10-1/4
(260)
*6-1/4
(159)
FRAME LINE
TOPOF DOOR
C
LHINGE OR PIVOT
ARM BRACKET
4-5/16
(109.5)
1
(25.4)
* To obtain extra closing force add 3" (77mm) to dimensions marked. This
will limit degree of door opening to 110° and void compliance with ADA
opening force guidelines.
MOUNTING DIMENSIONS MINIMUM
CLEARANCE
REQUIRED
OVER DOOR
TOP RAIL DIM. A DIM. B
2-1/2" (64mm)
& OVER
1"
(25.4mm)
3/4"
(19mm)
1-11/16"
(43mm)
1-3/4" (44mm)
-MIN.
5/8"
(16mm)
1-1/8"
(29mm)
2-1/16"
(53mm)

4
80-9330-3004-152 04/18
DC3200 Series Closer
Installation Instructions
A10 Heavy Duty Non-Hold Open Regular Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
2. Install Closer Bracket. (Figure 3)
Figure 3
Figure 4
MAIN ARM
Pin Hole
End
Countersunk
Holes
NOTE ARMS WILL
FORM A “V” POSITION
Rotate
approximately
5°
1/4-20 x 1/2 OHMS (2)
Pins
(2)
3. Mount Closer Body to Closer Bracket.
(Figure 4)
1/4-14 x 1-1/2
OH Self-Drilling (4)
or
1/4-20 x 3/4 OHMS w/Sex
Nuts (4) (M54 Option)
MAIN ARM
Pin Hole
End
Countersunk
Holes
NOTE ARMS WILL
FORM A “V” POSITION
Rotate
approximately
5°
1/4-20 x 1/2 OHMS (2)
Pins
(2)

5
80-9330-3004-152 04/18
DC3200 Series Closer
A10 Heavy Duty Non-Hold Open Regular Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
MAIN ARM
Pin Hole
End
Countersunk
Holes
NOTE ARMS WILL
FORM A “V” POSITION
Rotate
approximately
5°
1/4-20 x 1/2 OHMS (2)
Pins
(2)
4. Position Arm on Closer. (Figure 5)
Main arm projects straight out at 90° angle to
door.
5. Preload and Fasten Arm to Frame.
(Figure 6)
Close door, swing arms to align holes in arm
bracket with pre-drilled holes on frame and
install attaching screw.
NOTE: Arms will form a “V” position.
Extended Maintenance
Lubricate Arm periodically at shaded points
with a drop or two of appropriate lubricant.
Figure 5
Figure 6
MAIN ARM
Pin Hole
End
Countersunk
Holes
NO
TE ARMS WILL
FORM A
“V” POSITION
Rotate
approximately
5°
1/4-20 x 1/2 OHMS (2)
Pins
(2)
1/4-14 x 1-1/2
OH Self-Drilling
(2)

6
80-9330-3004-152 04/18
DC3200 Series Closer
Installation Instructions
A10 Heavy Duty Non-Hold Open Regular Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Adjustments
Adjustments (Figure 7)
(3/32 Allen Wrench Provided)
Closing Speed Valve (Figure 8)
To adjust speed of door closing from fully
open to a position 2 to 5" from closed, turn
Closing Speed Valve CLOCKWISE to SLOW
closing, COUNTER-CLOCKWISE to SPEED
closing.
Latching Speed Valve (Figure 9)
After closing speed has been obtained, turn
latching speed valve CLOCKWISE to SLOW
latching or COUNTER-CLOCKWISE to SPEED
latching for last 2" to 5" of door travel.
NOTE: Set combination of CLOSING and
LATCHING speeds to between 3 and 7
seconds. Use of door by handicapped,
elderly or small children, may require
even greater closing time.
Backcheck Intensity Valve (Figure 8)
Turn valve COUNTER- CLOCKWISE to reduce
backcheck or CLOCKWISE to increase
backcheck. (Backcheck should be set to give
a soft cushioning action, not a sudden stop).
Delayed Action Valve (Figure 8)
Turn valve CLOCKWISE to SLOW closing,
COUNTER-CLOCKWISE to SPEED closing.
Delayed action may be adjusted from 20
seconds to 90 seconds, depending on degree
of door swing. Delay occurs at the beginning
of the door closing cycle from fully open down
to 70°, where the closing speed valve then
begins its control.
Delayed Action
Option
M-71
Backcheck
Latch
Sweep
LATCHING
SPEED
VA LV E
Power
Size
Stamp
Date Stamp
BACKCHECK
INTENSITY VALVE
OPTION M71
DELAYED
ACTION VALVE
CLOSING
SPEED VALVE
SPRING POWER ADJUSTER
(5/16" WRENCH or SOCKET)
(FLAT TIP SCREWDRIVER)
Figure 7
Figure 8
Figure 9

7
80-9330-3004-152 04/18
DC3200 Series Closer
A10 Heavy Duty Non-Hold Open Regular Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Adjustments
Adjust Spring Power According to Chart
DC3200 Size 1-6 Adjustment (Figure 10)
• All DC3200 closers are factory set at an
approximate Size 3.
Full Cover(Standard)
Slim Cover (Option M76)
Figure 10
Figure 11
Size of Door No. of Full (360°)
Turns Clockwise of
Power Adjuster
Equivalent Closer
Size (Approx.)
Interior Exterior
In-Swinging
2' 4"
(712)
2' 6"
(764) 4 2
2' 6"
(764)
3' 0"
(915) 8 3
3' 0"
(915)
3' 6"
(1067) 12 4
3' 6"
(1067)
4' 0"
(1219) 16 5
Figure 12
4 Cover Installation
Full Cover(Standard)
Slim Cover (Option M76)
Install Cover (Figure 11)
Slip cover over closer. Hold tightly against
closer mounting surface. Secure on each
side with 6-32 x 1/4 PBHMS screws.
Slim Cover Option M76 only (Figure 12)
Position spindle cap over unused spindle
and secure with truss head screw.
• Adjust closer as necessary for door size
using this chart.
• Readjustment may be required to suit
prevailing conditions.

80-9330-3004-152 04/18
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Patent pending and/or patent: www.assaabloydss.com/patents
Corbin Russwin
225 Episcopal Road
Berlin, CT 06037
Phone: [phone]
Fax: [phone]
corbinrusswin.com
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]