Assa Abloy Sargent Electroguard-59 80 Series Assembly instructions

Installation and Wiring
Instructions For Electroguard®59-
Prefix 80 Series Exit Device to
ElectroLynx Connector System
For installation assistance, contact SARGENT at 800-810-WIRE (9473)
A7690C
3/08
© SARGENT Manufacturing Company 2008
A7690C.indd 1 11/8/18 9:01 AM

800-810-WIRE (9473) • www.sargentlock.com • A7690C
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
Table of Contents
General Description............................................................. 1
Parts Breakdown ................................................................. 1
Recent Product Enhancement to Aid Installation &
Adjustments......................................................................... 2
Optional Equipment............................................................. 3
Sample Elevation Diagram ................................................. 3
Cylinder Installation ............................................................. 4
Electroguard™Dip Switch Settings ...................................... 5
Basic Installation Instructions.............................................. 6
Exit Device Installation ................................................... 7-17
Exit Device Plug-in Connector Installation ........................ 18
Electroguard™Input/Output Diagram................................. 19
Electrical Specifications..................................................... 19
Input/Output Descriptions.................................................. 20
System Wiring Examples ............................................. 21-24
Operating Instructions .................................................. 25-27
Additional Features ........................................................... 27
Care of Finish Guide ......................................................... 28
Electroguard™Troubleshooting .................................... 29-33
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
ElectroLynx®
As part of their promise to provide innovative, fast and effective,
and higher security solutions to their customers, ASSA ABLOY
Group companies offer ElectroLynx, a universal quick-connect
system that simplifies the electrification of the door opening.
ElectroLynx®is a registered trademark of ASSA ABLOY, Inc.
A7690C.indd 2 11/8/18 9:01 AM

1
A7690C • 800-810-WIRE (9473) • www.sargentlock.com
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
NOTE: Field cut rail assemblies are not allowed. Exit Device must be ordered for specific 80 series type, specific door width
and finish from the factory. Consult factory with any questions @ 800-810-WIRE (9473).
The SARGENT 59- Electroguard™ is designed for areas which require a delayed egress requiring an alarm at the door when
any attempt is made to violate the door. The Electroguard™ can be tied into a fire alarm system, indicate latchbolt status and
control an alarm at a remote location when the door is in violation.
NOTE: Proper connections and appropriate peripheral hardware is required.
Part No. Description
52-2994 59- Circuit Board Replacement Kit for “F” size rails (Includes one 52-2558 circuit board and
“ F” size rail harness)
52-2995 59- Circuit Board Replacement Kit for “J” size rails (Includes one 52-2558 circuit board and
“J” size rail harness)
52-2996 59- Circuit Board Replacement Kit for “G” size rails (Includes one 52-2558 circuit board and
“G” size rail harness)
52-2558 Electroguard™ Circuit Board only
52-2204 Latchbolt Harness and Switch Assembly for 59-8800 and 8500 Rim Devices
52-2217 Surface Vertical Rod Harness and Switch Assembly for 59-8700 Devices
52-2220 Concealed Vertical Rod Harness and Switch Assembly for 59-8600 and 8400 Devices
52-2224 Latchbolt Harness and Switch Assembly for 59-8900 and 8300 Mortise Devices
Mounting rail
insert
Mounting
plate
Endcap
Circuit board
Cover
Chassis
assembly
Switch
assembly
Exit Device
Chassis Assembly
and Rail Assembly
Electroguard™
Circuitry
1” diameter hole required for
routing wires into the door Manual dogging is
provided standard on
non fire rated devices
General Description
Parts Breakdown
1
2
A7690C.indd 1 11/8/18 9:01 AM

2800-810-WIRE (9473) • www.sargentlock.com • A7690C
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
IMPORTANT
When servicing previous versions using circuit boards with 16-pin connector/harness, you must refer to Installation Manual A7043
for wiring and functional differences. Portions of the Troubleshooting section within this manual may be used for previous version
circuit boards
Plug-in connector system updates
New circuit board with 4 diagnostic LEDs with plug-in connector harness
• Standardized wire colors and connector terminations
• Separate 5-pin (J1) and 9-pin (J2) input harnesses. This
simplifies wiring terminations in most applications since
most applications require only the 5-pin harness
• Standard wire colors on 5-pin and 9-pin input harnesses.
IMPORTANT: Some wire colors have been changed from
previous version 59- circuit board
• 4 diagnostic LEDs for installation and troubleshooting
assistance:
Yellow LED – Indicates Latchbolt or Vertical Rod switch status
Green LED – Indicates whether the Rail Magnet is energized or
de-energized
Red LED – Indicates whether the Push Rail (REX) Switch is
activated or de-activated
Orange LED – Monitors the Door Status Switch position when
switch is being used
• Visible Yellow Insert LED has been eliminated. The Red LED
flashes now to indicate momentary egress
• Added wire for earth ground termination
• 16 position rotary switch has been changed to Dip Switch–
S2. Positions 3 and 4 are now used to select momentary
egress times
• Voice and Ganged features are now jumper selectable
• Red Visible Insert LED is ON to indicate fire alarm condition
rather than the Green Visible Insert LED
• Nuisance Delay is now 1 second (was 2 seconds)
Electroguard plug-in connector harness
5 & 9-pin to 8 & 4-pin connectors
8-pin
connector
4-pin
connector
3 loose wires
GREEN LED
RED LED
HORN
9
1
5
1
JP1 JP2 JP3 JP4
Two Insert LEDs
JP1 JP2 JP3 JP4
Harness with 5 and 9 pin connectors
and loose wires
9
1
5
1
Two Insert LEDs
S3 1234
YELLOW
LED
GREEN
LED
RED
LED
16 16
11
16-pin
connector
J1
S1
Harness with 16-pin connector
and loose wires
J5
Recent Product Enhancements to Aid
Installation and Adjustment
3
New circuit board with 4 diagnostic LEDs*
*Shipped after 2/29/04
Circuit board with 16-pin connector and no diagnostic LEDs*
*Shipped prior to 2/29/04
A7690C.indd 2 11/8/18 9:01 AM

3
A7690C • 800-810-WIRE (9473) • www.sargentlock.com
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
1. Determine locations of components at the door
2. Mountallhardwareandperipheralequipmentaccordingtomanufacturer’sinstructions
3. Power supply should be mounted near door to avoid power drop due to excessive wire runs
4. Features used will determine wire requirements of electric hinge or other power transfer*
123
456
789
0
*#
SARGENT
(Ordered Separately)
CAUTION!!
There are no user serviceable parts on the Electroguard™ Circuit Board. Consult parts breakdown for new Electroguard™ Circuit
Board.
There are two switches in the device: a latchbolt or vertical rod switch, and request to exit switch. Both are preset at the factory.
Tampering or breaking switches will cause malfunction.
All components must be installed according to prevailing electrical codes.
3510, 3530, 3560
Power supplies
TA2714 CC4
TA714 CC12
Electric hinge
3071/3072
Voice module
4291/4292
Keypad
4371LT
Key switch
3287
Door status switch
123
456
789
0
*#
Page 5 Art
Optional Equipment
4
Sample Elevation Diagram
5
A7690C.indd 3 11/8/18 9:01 AM

4800-810-WIRE (9473) • www.sargentlock.com • A7690C
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
1. Prepare door according to template and instruction sheet supplied with exit device
2. Verify 1-1/8” mortise cylinder (size 41) is installed in rail insert with collar prior to installing exit
device on door
TO ADD OR REMOVE CYLINDER
1. Ensure power is disconnected
2. Separate circuit board and ground wire from mounting insert by
removing the four (4) screws from the under side
3. Once separated, slide cylinder through
collar into the insert as shown
NOTE: Orientation of the cylinder
Secure the cylinder with cylinder nut.
Tighten firmly
4. Re-attach circuit board and ground wire
to mounting insert with four (4) screws
5. Operate cylinder and verify cam is
operating switch properly
SARGENT
SARGENT
Collar
Cylinder Nut
DIP Switches
Top View
(LHRB shown)
Side View
Cam (cam engages switch)
SARGENT
SARGENT
Collar
Cylinder
Insert
Cylinder nut
Cylinder Installation
6
ORIENTATION OF CYLINDER
A7690C.indd 4 11/8/18 9:01 AM

5
A7690C • 800-810-WIRE (9473) • www.sargentlock.com
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
Dip switch positions 3 and 4 - Used to select the momentary egress time of 5, 10, 20 or 40 seconds. This switch is preset at
the factory for five seconds
S2 Dip Switch Position Momentary
Egress Time
3 4
OFF OFF 5
seconds
OFF ON 10 seconds
ON OFF 20 seconds
ON ON 40 seconds
S2-1 Nuisance Delay - (Field selectable 0 or 1 second) A one second nuisance delay can be enabled by setting Dip
Switch (S2-1) to the On position. When nuisance delay is enabled, the unit will require the push bar to be depressed
for more than one second in order to trigger an irreversible alarm condition. If the push bar is released before the 1
second has elapsed, the unit will go back into the “delayed egress mode” and the alarm will not sound. Nuisance
delay is set to On position at factory
If the Dip Switch S2-1 is in the Off position, there will be no nuisance delay and alarm horn will sound
immediately when the push bar is depressed
S2-2 Nuisance Audible - (Field selectable on or off) An audible horn is enabled by setting Dip Switch S2-2 to the On
position. The internal horn will sound as soon as the push bar is depressed, signaling that the device is armed. If the
pushbar is held down for more than 1 second, an irreversible alarm condition begins. If Dip Switch S2-2 is in the Off
position, the horn will not sound during nuisance delay
Nuisance audible is set to On position at factory to sound horn when rail is depressed during nuisance delay
OFF
ON
S2-1 On - 1 second nuisance delay
S2-1 Off - no nuisance delay
S2-2 On - Nuisance Audible On
S2-2 Off - Nuisance Audible Off
OFF
ON
S2-1
Select Dip Switch Settings prior to installing exit device on door
S2
Electroguard™ Dip Switch Settings
7
S2-2
A7690C.indd 5 11/8/18 9:01 AM

6800-810-WIRE (9473) • www.sargentlock.com • A7690C
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
Inside
View of Door
Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on the inside of the door.
On inside of door, exit devices are oriented as follows:
8800 RHRB shown
Lights from top to bottom:
Red, Green
8800 LHRB shown
Lights from top to bottom:
Green, Red
Outside View Outside view
Inside View Inside view
Basic Installation Instructions
8
A7690C.indd 6 11/8/18 9:01 AM

7
A7690C • 800-810-WIRE (9473) • www.sargentlock.com
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
Exit Device Installation
9
Electroguard (59-, 12-59-)
80 Series Rail
with 8 and 4-pin connectors
and 3 loose wires
42
3 1
1, Violet (RAR - NC)
2, Grey (LBM - C)
4, Tan (LBM - NC)
3, Pink (LBM - NO)
Red/Green (Voice/Gang - C)
1
75
64
3
2
8
1, Black (-24)
2, Red (+24)
4, Green (EG)
3, White (FA)
5, Orange (EI)
7, Brown (RAR - C)
8, Yellow (RAR - NO)
6, Blue (DS)
Red/Black (Voice/Gang - NC)
Red/Yellow (Voice/Gang - NO)
Note: RAR, LBM and Voice/Gang contacts
shown are with power applied to rail
B. ElectroLynx Connector System Notes:
The system is designed to be installation friendly with
pluggable connectors from the electric hinge through the
door to the rail. The only wiring required is to the loose
wires on the pigtail harness assembly on the frame side
of the electric hinge
IMPORTANT:
The plug and receptacle connectors are designed to
mate and lock together as shown in the figure. Plug the
connectors into each other with the locking mechanism
aligned as indicated
Do NOT force connectors on any other way
A. IMPORTANT
Caution: Disconnect all input power before beginning installation to prevent electrical
shock and equipment damage
1. Installer must be a trained, experienced service person
2. All wiring must comply with applicable local electrical codes, ordinances and regulations
3. Field cut rail assemblies are not allowed. Exit device must be ordered for specific door width
Plug
Locking mechanism
Receptacle
A7690C.indd 7 11/8/18 9:01 AM

8800-810-WIRE (9473) • www.sargentlock.com • A7690C
4/15/08 Copyright © 2008 SARGENT Manufacturing. All rights reserved. Reproduction in whole or in part without the express written permission of SARGENT Manufacturing is prohibited.
C. Installation Notes:
1. With new applications, a raceway harness with 8 & 4-pin connectors will be pre-installed inside the door by ASSA ABLOY
door manufacturer when specified during the ordering process. Raceway harness kits are also available for retrofit
applications. For retrofit applications, refer to retrofit instructions
2. If door does not have a raceway harness with connectors, either consult factory for raceway retrofit kit or cut connectors off
product and hard wire, as required
3. Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail connector terminations
and wire colors all match
Exit Device Installation (continued)
Installing 59-8300/12-59-8300 Series Mortise Lock Exit Device
CAUTION – BEFORE STARTING:
• Check hand of door (This exit device is handed and not reversible)
• Door should be fitted and hung
• Verify box label for size of exit device, function and hand
PREPARE DOOR AND MOUNT LOCK –
Refer to Instruction Sheet A6696
1. Feed wire and connector through the mortise opening
and out the inside diameter
Rail wire &
connector
Wire &
connector
Chassis Wire holder
Chassis
arm
Vertical reference line C
Lchassis
Mortise lock body
Left hand reverse
bevel illustrated
Inside Of
Door
IMPORTANT: Surface of door where exit
device is to be applied must be flush.
Clear away any raised projections to allow
exit device to rest on flat surface of door
Cover
8400 Main Chassis Cover Dwg
8300 Mount Lock Dwg
Wire & connector Inside
diameter
Rail assembly
General Touch Bar
Lock Down Key —7/32” hex key
To operate: Depress pushrail,
insert hex key and turn clockwise.
(Not furnished with 12-)
Push rail
A7690C.indd 8 11/8/18 9:01 AM