Assa Abloy Norton 9510 Series User manual

80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
ASSA ABLOY
Multi-Sized 1 thru 6
with Heavy Duty Non-Hold Open
Parallel Arms
9510 Series
Installation Instructions
Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
IMPORTANT: An improperly installed or incorrectly adjusted door closer may cause property
damage or personal injury; and will void product warranty.
To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.
Door closers must be securely fastened to a properly reinforced door and frame
with fasteners provided.
An auxiliary door stop, BY OTHERS, is required for this Installation.
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
Size of Door & Door Closer
Type
of
Installation Interior Exterior
In-swinging
Exterior
Out -swinging
Recommended
Closer Size
**Max.
Opening
Force
lbs/f
2 4' "
2 6' "
3 0' "
3 6' "
4 0' "
4 6' "
2 6' "
3 0' "
*3 6' "
*4 0' "
8
14
16
22
24
26
1
2
3
4
5
6
**NOTE: These forces are for standard templating with bearing type hinges and do not account for pressure differentials and draft.
Parallel
Arm
RHR LHR
BEFORE
INSTALLING:
ADA compliant closer: 9510.
The Americans with Disabilities Act (ADA) requires that doors having door closers
have an opening force not to exceed 5 lbf.
The door closer's power size adjustment feature may require adjustment to its
lowest setting to comply with ADA opening force guidelines.
Page 2
Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
Components: Figure 1
Plastic Cover
(Standard)
Screw Pack
Closer Mounting
Bracket
Closer
9500-AB
Angle Support Bracket
Heavy Duty Non-Hold Open
Page 3
Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
9/32” (7 mm);
3/8” (9.5 mm) dia. x
3/8” (9.5 mm) deep on
door opposite to closer
Standard
Optional
Through-bolts and
grommet-nuts All
Preparation for Fasteners Figure 2
Door or Frame
Fasteners Drill-Sizes
#12-14 Self-Drilling Screw Wood
(see Note) 3/16” (4.30 mm)
1/4” - 20 machine screw Metal Drill: #7 (0.201” dia.)
Tap: 1/4” - 20
Hollow
Metal
9/32” (7 mm) through;
3/8” (9.5 mm) door face
opposite to closer
Aluminum
or Wood 3/8” (9.5 mm) through
Aluminum
or Metal No drill required
Page 4
Note: Wood doors/frames: drill 1/8" (3.2) pilot hole when using Self-Drilling Screws.
Always consult door/frame manufacturer for fastener compatibility with the material of their door/frame.
Approved 2018-01-19

2
(50.8)
2
(50.8)
2
(50.8)
1
(25.4)
1-1/2
(38.1)
SEE MOUNTING SCREW
SPECIFICATIONS
NOTE: ANGLE SUPPORT MUST BE
DRILLED AND TAPPED IN THE FIELD
9500-AB DOOR
FRAME
9500-AB
ANGLE SUPPORT BRACKET
5/8
(16)
FRAME STOP
TOP OF DOOR
C
L
HINGE
OR
PIVOT
DOOR
FRAME STOP
2-3/4
(70) 5/8
(16)
1-1/2
(38.1)
1/4
(6.35)
B
A
C
TYP.
15/16
(23.8)
3/4
(19) 1-3/8
(35)
Minimum Clearance
MOUNTING
BRACKET
10
(254)
1
(25.4)
3-1/16
(77.8)
1/2
(12.7)
Adp
3
(76.2)
4-3/4
(120.7)
3
(76.2)
3/8
(9.5)
MAXIMUM
OPENING Adp BApplication
90°
180°
7-1/2 (191)
3-1/2 (89)
11-5/8 (295)
7-5/8 (194)
C
27-3/4 (705)
23-5/8 (600)
Mounting Bracket Drop Plate Soffit Bracket
A
7-7/8 (200)
3-7/8 (98)
Clearance
9588 DROP PLATE
Mounting Holes (4)
HD Parallel Arm Template
Page 5
5/8
(16)
DOOR
FRAME
ARM
BRACKET
SPACER BLOCK
(When required)
NOTES:
• Check hand of door, see page 2.
• Right Hand Application Shown. Left Hand Opposite.
• Dimensions given in inches (mm). Do Not Scale Drawing.
• Closer must be installed mounted level to ensure
proper closer performance.
80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
• Attach arm to door frame.
• Connect arm to closer. Using hex wrench provided, turn closing speed
and latching speed valves clockwise until completely closed. DO NOT
OVER TIGHTEN. Open door to approximately 60°. Using wrench on
underside of spindle, rotate spindle approximately 135° toward hinge
edge of door. Install arm on spindle at an approximate 90° angle to door.
Reopen CLOSING SPEED VALVE. Install and tighten 5/16 Hex Head
Arm Washer and Screw Assembly.
• Select angle of opening and use dimensions shown in template to locate
4 holes on door for Closer Mounting Bracket (or 4 holes for
optional drop plate) and 6 holes on jamb for arm bracket (2 holes for
optional angle support bracket).
For applications that are different from above, a separate template will
be supplied for door and frame preparation.
• Prepare door and frame for fasteners using "Preparation for Fasteners"
chart, Figure 2, Page 4.
• Fasten Closer Mounting Bracket to door. Fasten optional drop plate to
door, only if it is required for the door conditions.
• Install closer body with tube end TOWARDS hinge, with valves:
DOWN for Left Hand door / UP for Right Hand door.
ROO
D
SPINDLE
ARM
CENTERLINE
ROOD
90°
SPINDLE
ROTATED
135°
Rotate 135°
60°
DOOR
135°
WRENCH
90°
ARM
• Make closer adjustments using information on page 7, then install
closer cover.
Page 6
HD Parallel Arm Installation Sequence
LEFT HAND DOOR SHOWN BELOW
ALL ANGLES SHOWN ARE APPROXIMATE
Approved 2018-01-19

Interior Exterior
In
Swing
Exterior
Out
Swing
Size of Door
Equivalent
Closer Size
(Approx.)
2 4 (712)' "
2 6 (764)' "
3 0 (915)' "
3 6 (1067)' "
3
4
5
6
2 6 (764)' "
3 0 (915)' "
2 6 (764)' "
3 0 (915)' "
3 6 (1067)' "
4 0 (1219)' "
2-7
7-11
11-15
15-17
Spring Power
Adjustment
No. Full Turns
Clockwise
LATCHING
SPEED VALVE BACKCHECK
INTENSITY VALVE
CLOSING
SPEED VALVE
SPRING POWER ADJUSTER
(1/4 ALLEN WRENCH)"
SPRING POWER ADJUSTMENT CHART
Spring Power Adjustment
Size 1 thru 6 Adjustment See Chart
All 9500 closers are factory set at an approximate Size 3.
Adjust closer as necessary for door size using this chart.
Readjustment may be required to suit prevailing conditions.
Locate spring power adjuster from
Illustration below
Backcheck Intensity Valve
Factory preset for typical doors.
Turn valve COUNTER-CLOCKWISE to reduce backcheck
or CLOCKWISE to increase backcheck. (Backcheck should
be set to give a soft cushioning action, not a sudden stop.)
Latching Speed Valve
Factory preset for typical doors.
After closing speed has been obtained, turn latching speed valve
CLOCKWISE to SLOW latching or COUNTER-CLOCKWISE to
SPEED latching for last 2 to 5 of door travel." "
NOTE: Set combination of CLOSING and LATCHING speeds to
between 3 and 7 seconds Use of door by handicapped,
elderly or small children may require even greater
closing time.
Closing Speed Valve
Factory preset for typical doors.
To adjust speed of door closing from fully open to a position
2 to 5 from closed, turn Closing Speed Valve CLOCKWISE" "
to SLOW closing, COUNTER-CLOCKWISE to SPEED
closing.
Delayed Action Valve
Factory preset for typical doors.
Turn valve CLOCKWISE to SLOW closing, COUNTER-
CLOCKWISE to SPEED closing. Delayed action may be
adjusted from 20 seconds to 90 seconds, depending on
degree of door swing. Delay occurs at the beginning of the
door closing cycle from fully open down to 70°, where the
closing speed valve then begins its control.
h
e
k
c
c
c
k
a
B
h
c
t
a
L
d
e
e
p
S
g
n
i
s
o
l
C
y
e
l
a
d
e
D
t i
o
c
n
A
Option
(1/8 Allen Wrench Provided)
(1/8 Allen Wrench Provided)
(1/8 Allen Wrench Provided)
Date Stamp
(on end of closer)
MM-YY
OPTIONAL
DELAYED
ACTION VALVE
MM = Month
YY = Year
Unit Adjustment
Page 7
80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
Approved 2018-01-19

80-9395-9513-020 REV. 2 (01-18)
Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.
Copyright © 2013, 2018 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
ASSA ABLOY
Page 8
Installing Cover
Insert is removable.
Place in unused opening.
Plastic Cover
(Standard)
3000 Highway 74 East • Monroe, NC 28112
Tel: (877)- • Fax: [phone]-2255
www.nortondoorcontrols.com
ASSA ABLOY
Approved 2018-01-19