Assa Abloy SARGENT 281 Series User manual

Install the closer
with spring
adjustment screw
towards hinge.
Install the mounting
bracket with the arrow
pointing up for both
RH and LH doors.
Right Hand
Door Shown
Drill & Tap, use screws provided or use
Mortise Nuts when required.
2. Install mounting bracket and closer.
Use information provided in Step 1 above and the
template provided on page 4 to locate and drill holes.
3A. Alternate Option:
Pre-assemble arm prior to
attaching stop.
B
1"
(From Stop)
3"
10-3/8"
Centerline
of
Hinge
A
Centerline
of Hinge
13/16"
2-11/16"
1-7/8"
5/16" 13/16"
1-15/16"
3-1/16"
3-7/8"
IMPORTANT NOTICE
Pre-drill 3/32" holes
for self-tapping
screws or tap #12-24
for machine screws.
1. Prepare door and frame.
yDetermine maximum degree of door opening or
hold open (CPSH) required.
yDrill and tap door and frame for #12-24 machine screws.
When using self tapping screws provided, pre-drill with
3/32" drill.
LEFT
HAND DOOR
RIGHT
HAND DOOR
PULL
HINGE SIDE PULL
HINGE SIDE
STOP (PUSH) SIDE STOP (PUSH) SIDE
Closers are non-handed
3. Install stop and foot bracket to door stop.
12-24 x 1-3/4" MS
or #12 x 2-1/2"
Insert
(CPSH only)
Four (4) #12-24 x 5/8" MS
or #12 x 1-3/4"
Arm must be the same hand
as the door. Assemble holder
with bumper and insert (CPSH
only) to foot bracket . Location
of these parts determines the
“hand”.
RH CPSH Shown
CPSH Arm Shown
CPS Arm is similar
1/2"
7/8"
5/8"
Use fifth hole
spacer when
required.
IMPORTANT: Use a minimum of 7 screws.
Mount foot bracket to door stop.
Degree of Door Opening at Hold Open n
85° 90° 95° 100° l105° l
Dim A 9-7/16" 8-3/4" 8-1/8" 7-9/16" 7-1/16"
Dim B 4-9/16" 3-15/16" 3-5/16" 2-11/16" 2-3/16"
lDo not use with swing clear hinge for door openings greater than 95°. Use
alternate type of hinges.
nDimensions for given degree based on 4-1/2" hinge. When 5-1/2" to 6"
hinges are used, hold open angle will change by less than 1/2" . Dead stop
occurs 3° beyond hold open.
Spring Power
Adjusting Screw
Right Hand Door
Shown
Left Hand Door
Opposite
12-24 x 1" MS
or #12 x 1-3/4"
Bumper &
Holder
5/8"
9/16"
1-800-727-5477 • www.sargentlock.com
A7319F 12/22 Rev 6
Installation Instructions
281 Series
Door Closer with CPS/CPSH Arms
281 Series Adjustable from Sizes 1 thru 6
Copyright © 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express written permis-
sion ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
Approved 2022-12-08

4. Attach Arm to Spindle
WARNING: If not properly indexed, door closer will not
function properly.
A. Rotate bottom spindle with wrench.
B. Assemble main arm with index mark positioned as shown.
C. Secure with screw and washer.
4A. Alternate Option:
Attach Pre-Assembled Arm to Spindle.
Left Hand
Door
Index Mark
on Spindle
45° 45°
Right Hand
Door
Index Mark
on Spindle
5. Install Pivot
A. Open door and install pivot as shown.
B. Use screw to secure pivot and arms.
Accessories
281 Drop Plate
Used with narrow top rails.
125 V Bracket
For narrow frame conditions.
Frame
Door
Stop
Mortise Nut
Drill 3/8" dia.
hole for Mortise
Nut body
Unreinforced
Door
Drill 1/4" dia. hole for
mounting screws
Optional: Mortise Nut Mounting
Use Mortise Nuts (#4TB)
when thru-bolting is required.
Refer to pages
1 and 4
for templating
dimensions
281-D DROP PLATE
Window
125 VF Bracket
For flush frame and
door conditions. Flush
Frame
Door
Door
Main
Arm
Main
Arm
2
1-800-727-5477 • www.sargentlock.com A7319F 12/22 Rev 6
281 Series
Installation Instructions
Door Closer with CPS/CPSH Arms
Copyright © 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
Approved 2022-12-08

Final Adjustment and Regulating Procedures
Install Cover
Install cover with two (2) security screws as shown.
Latching
Speed Range
Closing Speed
Range
Delayed
Action Range
Backcheck
Range
+-
Increase
Power Decrease
Power
Counterclockwise
(CCW)
Clockwise
(CW)
1/4" Allen Spring Power
Adjusting Screw
Adjust closing power to the minimum force required to reliably close and latch door.
yIf door is hard to open, decrease power slightly.
yIf door does not latch, increase power as required.
yUse chart below as a starting point.
yDoors adjusted with high closing power to overcome strong
draft conditions may exceed ADA standards.
Door Width
in inches
Exterior Doors Interior
Doors *
24 - 30 2 - 7 turns CW 1-5 turns CCW
30 - 36 7 - 11 turns CW 3-6 turns CCW
36 - 42 11 - 15 turns CW Factory Set
42 - 48 15 -17 turns CW 8 turns & Up CW
* If interior doors do not have to comply with ADA requirements, exterior settings
are recommended. Where strong drafts exist, increase spring power as needed.
NOTES:
‒Adjusting door to close due to high draft conditions may
exceed ADA standards.
‒Consult local ordinances when fire doors are involved.
To Adjust Holder Arm (CPSH Arm ONLY)
Adjusting Nut
All CPSH arms are shipped in Non-Hold Open from
the factory. To set in Hold Open, turn the adjusting nut
approximately 1-1/2 turns clockwise.
yRecommend 6 second minimum from 90° to the closed position.
yClosing and Latching Speeds: Turn valves clockwise to slow down or counterclockwise to speed up door movement.
yBackcheck: To regulate the intensity of backcheck action, turn valve clockwise to increase or counterclockwise to decrease check-
ing. CAUTION: Set valve for slight cushioning effect; Closer can be damaged if the checking action is too abrupt. Never use the
backcheck as a door stop. Always use a door stop to stop the door.
yDelayed Action Feature (Optional on some models): Delayed action provides slow door closing through the delayed action range.
Turn valve clockwise to slow down or counterclockwise to speed up door movement.
Insert is
removable.
Place in unused
opening.
Latching
Speed Valve
Closing Speed
Valve
Delayed
Action Valve
(Optional)
Backcheck
Valve
1/4" Spring Power
Adjustment Screw
Decrease
( – )
Increase
( + )
Faster
( + )
Slower
( – )
Use hex socket (1/8” Allen) wrench to adjust Latching Speed,
Closing Speed, and Delayed Action valves.
To regulate the intensity of backcheck action, use hex
socket (1/8" Allen) to turn valve clockwise to increase or
counterclockwise to decrease checking
3
1-800-727-5477 • www.sargentlock.com
281 Series
Installation Instructions
Door Closer with CPS/CPSH Arms
Copyright © 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent
www.assaabloydss.com/patents.
A7319F 12/22 Rev 6
Approved 2022-12-08

1-800-727-5477 • www.sargentlock.com
Copyright © 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited.
Patent pending and/or patent www.assaabloydss.com/patents.
    
  
     
     
     
 
 
   
   
   
 
 
 -


5 1 /2 •
i


 

 


 
         
  
    


  •
I   : �- t    
  
   
        
   
 
 
 


 
  


        
   
         
         
       
      
             
            
      
       
      
        


    
  
  
   
 
 


9 ufacti C
     
    
    
   
 


 
 
Template
A7319F 12/22 Rev 6
Attention Installer: Improper installation
may result in damage to the product and
void the factory warranty.
WARNING
WARNING
This product can expose you to lead which is known to the state of California to
cause cancer and birth defects or other reproductive harm. For more information
go to www.P65warnings.ca.gov.
Approved 2022-12-08