Assa Abloy NORTON RIXSON 6300 Series User manual

80-9363-0005-020 Rev 7 12/23
6300 Series Full Feature Low Energy Operator
Models 6311, 6351 (Pull Side)
Installation Instructions
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
Pour la version francaise voir NortonRixson.com.
READ AND FOLLOW ALL INSTRUCTIONS.
SAVE THESE INSTRUCTIONS.
This product can expose you to lead which is known to the
state of California to cause cancer and birth defects or other
reproductive harm. For more information go to:
www.P65warnings.ca.gov.
WARNING
6351 Pull Side Double Egress Up to 130° opening (Right Hand Shown)
Double Egress
Pull Arm Pkg
(6350-1L (LH);
6350-1R (RH)
Cover (6300COV2)
End Cap Kit
(6300END)
Power Supply
(6300CM)
Standard Pull Arm Pkg
(6310-1)
End Cap Kit
(6300END)
Backplate
Closer Body
(6300LAP)
Track
(7100-1T)
Tools Needed
6311 Pull Side Up to 180° opening
1/4-20
#7
#2 and #3
10" or 12"
3/16"
1/2"
3/4"
Deep
Well
#16 12-24
Punch
3/16" 3/32"
1-314"
2x
Zip
Ties
2x
Track Option
#12-24 x 1-3/4"
Sleeve Nut
& Bolt
2x
Track Option
#12-24 x 1-3/4"
1x
Arm
1/4-20 x 7/8"
with nut
1x
Cable
Retaining Clip
2x
Cable
Retaining
Clips
10x
Backplate
1/4-20 Machine or
#14 x 2-3/4" Wood
4x
Closer Body
1/4-20 x 3-3/4"
6x
Power Supply
& End Caps
1/4-20 x 3/8"
Supplied Fasteners
The table below provides a list of documents associated with this product. These documents are available for download
from www.nortonrixson.com. If additional information or assistance is needed, contact Technical Product Support.
Document Title Document Number
6300 Series Quick Start Guide 80-9363-0014-020
6300 Series Operator Programming Guide 80-9363-0015-020
6300 Series Operator, 6312/6352 Pull Side Double Egress Installation Instructions 80-9363-0008-020
6311/6351 Pull Side Template, 36-48" Door Width, 90-250 lb. Door Weight, 180° Max Open Angle 80-7363-0001-020
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
2
6311/6351 Series (PULL Side) Power Operator
Technical Data
Input power: 120VAC, 60Hz 3.0A NOTES:
yPermanent wiring is to be employed as required
by local codes.
yActivation devices: push plates, access control,
mats, touchless wall switches, etc.
yMaximum wire size is:
‒12AWG at terminals LINE and NEUTRAL
(120VAC; 60Hz) on Power Input Terminal
‒14AWG at all other terminals
Power supply: 24 V DC, max. 6.5 Amp. ; 1.3A Available for
Acc.
Door width: 36 - 48" (91-122 cm)
Door weight: 90-250 lb. (41-113 kg)
Push min angle: 110° with reveal of 6-3/4" max
Push max angle: 130° with reveal of 1/8" min
Pull max angle: 180°
Hold open time: 5-30 seconds (A.D.A. 5 seconds min.)
Indefinite for Hold Open Input or End Cap 3
Position Switch
WARNING: To reduce risk of injury to person, use this operator only with Pedestrian Swing doors. FOR INDOOR USE ONLY
Product Safety Warnings
Certifications and Standards
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Install only on a properly operating and balanced door.
A door that is operating improperly could cause severe
injury. Have qualified service personnel make repairs to any
hardware before installing the operator.
3. Remove, or make inoperative, all locks (unless mechanically
and/or electrically interlocked to the power unit) that are
connected to the door before installing the operator.
4. Do not connect the door operator to the source power until
instructed to do so.
5. Never let children operate or play with door controls. Keep
remote control (when provided) away from children.
yETL Certified: Operator conforms to ANSI/UL standard 325 for automatic closing doors and UL10C Positive Pressure
Fire Test for Door Assemblies.
yANSI A156.19: These products are designed to conform to this specification “for power assist and low energy power
operated doors.” These products are designed to exceed all the requirements for “Low Energy Power Operated
Door”.
yAmericans with Disabilities Act (A.D.A.): These door operators can be installed and adjusted to conform with A.D.A.
regulations.
yANSI A117.1: These door controls permit door assemblies to conform to the requirements of this specification “for
buildings and facilities - providing accessibility and usability for physically handicap people”.
6. Personnel should keep away from a moving door
in motion.
7. Test door’s safety features at least once a month.
After adjusting either force or limit of travel, retest
door operator’s safety features. Failure to adjust
operator properly may cause severe injury or death.
8. KEEP DOOR PROPERLY OPERATING. See Door
Manufacturer’s Owner’s Manual. An improperly
operating door could cause severe injury or death.
Have a trained door systems technician make
repairs.
9. SAVE THESE INSTRUCTIONS.
Contents
Certifications and Standards...............................................................2
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Product Safety Warnings ..................................................................2
Before You Begin ..........................................................................3
Installation.................................................................................3
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
3
6311/6351 Series (PULL Side) Power Operator
Before You Begin
yThickness recommended for
reinforcements in hollow metal doors and
frames is charted.
yThis template information based upon use
of 5" maximum width butt hinges.
yMaximum frame reveal is 1/8" for 6311 units
and 1/8" up to 2-3/4" maximum for 6351
units.
yBefore beginning the installation, verify
that the door frame is properly reinforced
and is well anchored in the wall.
yConcealed electrical conduit and concealed
switch or sensor wires should be pulled to
the frame before proceeding.
Fasteners for Frame:
y1/4-20 Machine screws for hollow metal and
aluminum.
yNo. 14 x 2-3/4" (70mm) long sheet metal
screws for wood.
1/8"
(3)
Door
Frame
Hollow Metal Door Frame Reinforcing
Frame Material Reinforcing
Recommended Min. Required
12 Ga.
.1046
(2.66)
12 Ga.
.1046
(2.66)
18 Ga.
.0478
(1.21)
14 Ga.
.0747
(1.90)
10 Ga.
.1343
(3.41)
12 Ga.
.1046
(2.66)
16 Ga.
.0598
(1.52)
10 Ga.
.1343
(3.41)
12 Ga.
.1046
(2.66)
18 Ga.
.0478
(1.21)
8 Ga.
.1644
(4.18)
10 Ga.
.1343
(3.41)
A. Mount backplate.
1. Determine right hand or left hand installation.
(Figure 1)
2. Measure and mark first mounting hole according to
template. (Figure 2)
3. Attach backplate to frame with screw.
Do not fully tighten screw at this time.
For Metal Frames:
Use #7 drill and 1/4-20 tap for 1/4-20 machine
screws.
For Wood Frames:
Use 3/16" drill and supplied screws for self drilling, self
tapping screws.
4. Ensure backplate is level and aligned with door frame.
(Figure 3)
5. Using backplate as guide, mark and drill second hole.
(Figure 3)
6. Insert second screw and tighten both screws.
7. Using backplate as a guide, drill and tap remaining
eight (8) holes in frame. (Figure 3)
8. Secure with eight (8) screws and tighten.
Installation
Template
Figure 1
Figure 2 Right Hand Shown
Figure 3
Pull Side
Push Side
Left Hand
PULL
Right Hand
PULL
Remaining 8 Holes
2nd
Hole
Remaining 8 Holes
2nd
Hole
Right Hand ShownLeft Hand Shown
1-5/16"
Frame Edge
to 1st Hole
1-1/16"
Frame Edge
to 1st Hole
2" Min.
Frame Width
Hinge
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
4
6311/6351 Series (PULL Side) Power Operator
B. Mount track.
1. Measure and mark track mounting
holes using template. (Figure 4)
2. Drill holes.
a. For reinforced doors, drill and
tap holes with #16 drill and 12-24
tap.
b. For wood doors or self-drilling
screws, use 3/32" drill.
c. For sleeve nuts and bolts, see
illustration. (Figure 5)
3. Attach track using two (2) supplied
fasteners for application.
4. Snap track cover into place.
NOTES:
ySlider assembly and end caps
must be in track before screws can
attach track to door. (Figure 6)
ySlider must slide freely in track.
Template
Figure 4
End Cap
Slider Assembly
End Cap
Figure 5
Shorten sleeve
nut body to
this length
FRAME
Track
DOOR
Ø1/4"
Drilled Hole Ø3/8" Hole
Sleeve Nut
Head
DOOR
STOP
Ø5/8" Hole
1/8"
Figure 6
19-1/8"
Center to Center
9-3/4"
Door Edge
to Hole Center
7/16"
Top of Door to
Mounting Holes
OR
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
5
6311/6351 Series (PULL Side) Power Operator
D. Install closer body assembly.
1. Using four (4) screws, install closer
body to backplate. (Figure 8)
NOTES:
yScrews must be tightened in
a cross pattern until all four (4)
screws are tight. (Figure 8)
yCloser body is in proper
orientation for PULL SIDE
application when tube is AWAY
from backplate. (Figure 8)
2. Using three (3) supplied cable
management clips, secure cables
along closer body. (Figure 9)
1
4
2
3
Figure 7
Figure 8 Right Hand Shown
Tube AWAY
from backplate
Hinge
C. Install end caps.
1. Install two (2) screws on each end
of backplate leaving about 3/16"
gap between head of screw and
backplate. (Figure 7)
2. Slide end caps behind screw heads
and tighten screws. (Figure 7)
NOTE: End cap with 3-position switch
is always located on conduit side of
backplate.
NOTE: To retrofit closer assembly to an
existing operator, screws and fan inside
of end cap must be removed.
Switch End Cap
End Cap Screws
Conduit Hole
Figure 9
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
6
6311/6351 Series (PULL Side) Power Operator
F. Install arm.
1. Using an adjustable wrench, rotate
top pinion 45 degrees toward door
hinge. You will feel resistance from
spring. (Figure 12)
2. While holding pinion at 45
degrees, slide arm on bottom
pinion at orientation shown.
(Figure 12)
3. Using hex wrench, secure arm to
pinion with screw and nut.
(Figure 13)
4. Open door approximately 30
degrees and attach arm to slider in
track. Use hex wrench to tighten
slider bolt counter clockwise until
slide is tight in arm. (Figure 13)
5. Close door.
Track Slider Bolt
Figure 10
1. Insert two (2) screws. Leave 3/16" gap
between head of screw and backplate.
(Figure 10)
2. Slide power supply key holes over screws
allowing narrow slots of key holes to rest
on screws. (Figure 10)
NOTE: Narrow slots of key holes are
always at top and control board is always
at bottom for proper installation. (Figure
10)
3. Tighten screws.
4. Plug motor and ribbon cables from
closer body into power supply. (Figure 11)
NOTES:
yUse slot in power supply to feed con-
nectors to board. (Figure 11)
yUse provided zip ties to manage
any excess cable between closer
and power supply so that cover
can be attached without damaging
cables. (Figure 11)
5. Connect switch to power supply.
(Figure 11)
E. Install power supply assembly. Key Hole
3/16" Gap
Cable Slot
Motor Cable
Connection
Ribbon Cable
Connection
Figure 12
Figure 13
Control Board
3 Position Switch
Cable Connection
Figure 11
Zip Tie
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
7
6311/6351 Series (PULL Side) Power Operator
G. Adjust closing force.
NOTE: The amount of effort to manually
open or close a door is called closing force.
1. Using 1/2" socket wrench with 3/4" deep
well socket, turn nut in end of closer
body tube to desired force. (Figure 14)
NOTE: Window in closer tube shows
spring. (Figure 15)
NOTE: If additional closing force is only
required in latching region, see Latch
Boost and Lock Release features in
separate programming manual
80-9363-0015-020.
NOTE: Attach cover after initial
programming has been done. See separate
programming manual 80-9363-0015-020.
1. Align cut-outs in cover to pinion shafts.
(Figure 16)
2. Slide cover onto unit using end caps as
guides.
3. Snap cover securely to back plate.
4. Attach a label plate to each end cap by
snapping into place by hand with gentle
pressure. (Figure 16)
H. Attach cover and end cap label plates.
WARNING: Make sure no wiring is
loose or can be caught by cover
when it is snapped into place.
Spring Window
The 6311 or 6351 PULL SIDE Low Energy Operator has now been installed.
Continue with separate Programming Manual 80-9363-0015-020 to set up and adjust operator.
Figure 14
Figure 15
Figure 16
Approved 2024-02-13

80-9363-0005-020 Rev 7 12/23
Norton Rixson is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.
Copyright © 2019, 2021, 2023, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
Technical Product Support:
Monroe, NC 28112 USA
Phone: [phone] ext: 2
[e-mail]
NortonRixson.com
This page intentionally left blank.
Approved 2024-02-13