Assa Abloy Rockwood OH200 Series User manual

Template No.
T-OH200
Rev. 04/24/12
NOTE: Rockwood reserves the right to make product changes and is not
responsible for obsolete template errors. To ensure your template is current,
please visit our website at www.rockwoodmfg.com or call us at 800-458-2424.
OH200 Series Concealed Door Stops and Holders
300 Main Street • Rockwood, PA 15557 • P: 800-458-2424 • F: 800-922-9212 • Website: www.rockwoodmfg.com
©04.12 RMC
Rev. A
INSTALLATION INSTRUCTIONS
1. Select proper dimensions from chart on opposite
side of page.
NOTE: Add 5/8" to "A" dimension for dead stop.
2. Locate "B" dimension on frame and mortise 3/16"
deep for jamb bracket as shown.
3. Locate "A" and "F" dimensions on centerline of door
and mortise 13/16" wide x 7/8" deep for channel.
1/16" head clearance shown. Coordinate the arm
and rail cutout dimensions if head clearance varies.
4. Locate "C" and "E" dimensions on top of door and
mortise 1/4" deep as shown for arm clearance.
5. Install door stop or holder with screws provided.
NOTES:
• All hollow metal frames are to be provided with
3/16" min. thickness x 12" min. length
reinforcement plates.
• All hollow metal doors are to be properly reinforced
as shown.
• If dead stop is required add 5/8" to "A" dimension
as noted on opposite side of page.
• A, B and C dimensions are measured from
centerline of pivot, not edge of door.
• Reversible, non-handed.
• All dimensions are given in inches.
FASTENERS:
Jamb: #12-24 x 1/2" FH MS or #12 x 1-1/2" FH WS.
Door: #12-24 x 1-1/2" FH MS or #12 x 1-1/2" FH WS.
CAUTION: Note location
of swing clear hinge
centerline to determine
"A" and "B" dimensions.
Not To Scale

Template No. T-OH200
Rev. 04/24/12
OH200 Series Concealed Door Stops and Holders
300 Main Street • Rockwood, PA 15557 • P: 800-458-2424 • F: 800-922-9212 • Website: www.rockwoodmfg.com
©02.12 RMC
Rev. A
NOTE: Rockwood reserves the right to make product changes and is not responsible for obsolete template errors.
To ensure your template is current, please visit our website at www.rockwoodmfg.com or call us at 800-458-2424.
Device Number
1-3/4 - 2-1/4
Butts
&
3/4 Offset
Pivot
Device Number
When using center hung pivots, check pivot manufacturer's compatibility prior to specifying.
OH200 Series Concealed Door Stops and Holders
1. See other side for installation instructions.
2. Select proper dimensions noted below.
3. Add 5/8" to "A" dimension for dead stop.
4. All dimensions given in inches.
TO SELECT DEGREE OF STOP
1. With a 3/16 hex key wrench, loosen the set screw in the shock block.
2. Open door to desired degree of opening.
3. Slide shock block and spring until the spring touches slider cam.
4. Tighten set screw.
5. Verify door opening position and re-adjust, as needed.
* Butt mounting only. Reversible, non-handed.
Center
Hung
Stop Multi Door Opening A B C E F
201S 201M *18 - 24 1-3/16 3-11/16 0 15-5/16 15-7/8
202S 202M 24-1/16 - 30 4 4-3/8 2-9/16 16-9/16 17-1/16
203S 203M 30-1/16 - 36 6-3/4 5-9/16 4-11/16 19 18-13/16
204S 204M 36-1/16 - 42 9-7/8 7-1/4 6-3/8 23 21-1/4
205S 205M 42-1/16 - 48 13-13/16 8-1/2 7-5/8 27-1/2 23-1/16
Stop Multi Door Opening A B C E F
- - - - - - - -
202S 202M 27 - 32 5-7/16 6-1/8 5-1/4 15-5/8 17-1/16
203S 203M 32-1/16 - 38-1/2 7-3/16 6 5-9/32 19 18-13/16
204S 204M 38-9/16 - 45 10-5/16 7-11/16 6-13/16 23 21-1/4
205S 205M 45-1/16 - 48 14-1/4 8-15/16 8-1/16 27-1/2 23-1/16