Assa Abloy Norton CloserPlus CLP8101 User manual

Copyright © 2007, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2209-020 (05-14)1
ASSA ABLOY
Installation InstructionsModel Numbers Included:PR8101(H) / PR810X(H)PR8301(H) / PR830X(H)PR8501(H) / PR850X(H)CLP8101(T) / CLP810X(T)CLP8301(T) / CLP830X(T)CLP8501(T) / CLP850X(T)Note ‘X’ Designates Size 2, 3, 4, 5, or 6Parallel Rigid Arm Door Closers (PR)®CloserPlus Door Closers (CLP)Additional Closer Options:- “DA” indicates Delayed Action closing. - “H” indicates Hold-Open function for “PR” prefix units. The arm is handed.- “T” indicates Thumbturn actuated Hold-Open control for “CLP” prefix units. Optional Accessories:- 8148 Drop plate- 2019L, 6890, 6891 Soffit Plate Accessories. NOTE: For special applications a separate door and frame preparation template is packed with these instructions. In those cases, use this instruction sheet for installation sequence and closer adjustments only. Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR
Hinge Edgeof Door
Hinge Edgeof Door
Narrow Frame InstallationCloser mounts on opposite to hinge (push) side of door. CLP8500 CloserPlus arm illustrated. Full Cover shown.6890 and 6891 accessories required for this application (supplied separately).See Pages 3 and 4 Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR
Hinge Edge of Door
Hinge Edge of Door
Standard Frame InstallationCloser mounts on opposite to hinge (push) side of door. PR8300 Parallel Rigid Non Hold Open arm illustrated. Slim Line Cover shown.See Pages 3 and 4 Right Hand Door – RHLeft Hand Reverse – LHR Left Hand Door – LHRight Hand Reverse – RHR
Hinge Edgeof Door
Hinge Edgeof Door
Flush Partition InstallationCloser mounts on opposite to hinge (push) side of door. CLP8100T CloserPlus arm with Thumbturn Hold Open illustrated. Closer Cover not shown. 2019L accessory required for this application (supplied separately).See Pages 3 and 4An incorrectly installed or improperly adjusted door closer can cause property damage or personal injury. These instructions should be followed to avoid the possibility of misapplication or misadjustment.
CAUTION
CAUTION
ASSA ABLOY

Copyright © 2007, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2209-020 (05-14)2
ASSA ABLOY
Components Pinion Cap [1639]Standard Slim Line Plastic Cover[8300/8301]Optional Full Metal Cover [8500M/8501M] Insert Cutouts CoverInsertOptional Architectural Plastic Cover *[8500A/8501A]StandoffStandoff Insert Cutouts CoverInsertStandard Full Plastic Cover[8500/8501] Cover Screw Cover Screws Optional Architectural Metal Cover *[8500MA/8501MA]StandoffsCLP Arm AssemblyStop onlyRiveted ElbowRemovable StopPR Hold Open Arm AssemblyRiveted ElbowFriction Hold Open NutCLP Arm Assemblywith ThumbturnRiveted ElbowRemovable StopThumbturn Hold OpenScrew PackCloserArmSecondary ArmMain ArmMain ArmScrewSoffitPlateBackcheck ValveDelay Valve(Optional)Latch ValveSweep ValvePowerAdjustmentShaftCloserBodyPR Arm AssemblyRiveted ElbowArm OptionsCover OptionsOptionalAccessoriesFor Blade Stop6891 SpacerFor Frameor Blade Stop6890 BracketFor Flush Partition2019L Bracket2019S Block(provided) 9/32” (7 mm);3/8” (9.5 mm) dia. x3/8” (9.5 mm) deep ondoor opposite to closerStandardOptionalThrough-bolts andgrommet-nutsAllPreparation for FastenersDoor or FrameFastenersDrill-SizesSelf-Drilling ScrewWood(see Note)3/16” (4.30 mm) (pilot hole required)1/4” - 20 machine screwMetal Drill: #7 (0.201” dia.)Tap: 1/4” - 20 Sleeve nuts and boltsHollowMetal9/32” (7 mm) through;3/8” (9.5 mm) door faceopposite to closerAluminumor Wood3/8” (9.5 mm) throughAluminumor MetalNo drill requiredNote: Pilot hole required when using self-drilling screws for wood door/frame applications.* Note:Closers wtih ‘PR’ prefix cannot be installed on doors swinging beyond 120° when using 8400A or 8400MA cover.
8400P Cover
8200P Cover
8400M Cover
8400A Cover
8400MA Cover
Identify Arm Hand “R” for Right Hand Door“L” for Left Hand Door
L
Insert Cutouts CoverInsert

Copyright © 2007, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2209-020 (05-14)3
ASSA ABLOY
PR8101/PR8301/PR8501CLP8301/CLP8501InteriorExteriorInteriorExterior28-32 in0.7-0.8 m33-36 in0.85-0.9 m37-42 in0.95-1.05 m43-48 in1.1-1.2 mDoorSize
Full Clockwise Turns of Closer Power Adjustment Shaft
Power Adjustment Chart
NOTE: Maximum of 20 turns (360°) of Power Adjustment Shaft.Closer is shipped set at mid power setting.
799101012111213151314161815161) Start (wrench) here (bottom shaft)2) Rotate 50° to here3) Install arm here (see below for details)Arm Mounting Detail Select angle of opening and use dimensions shown on Page 4 and Dimension Chart below to locate 4 holes on stop side of door for closer body (or 8148 drop plate, only if required, see page 5) and 5 holes on stop and/or rabbet for Soffit Plate. For applications not covered in these instructions, a separate template will be required. Prepare door and frame for fasteners. See “Preparation for Fasteners”, Page 2. Set approximate closer power for door size using Power Adjustment Chart below. Use 1/8” hex wrench supplied to adjust Power Adjustment Shaft (set at 8 turns from factory) ... 20 turns maximum. Turn nut CLOCKWISE to Increase, COUNTER-CLOCKWISE to Decrease power. See Page 6 for the illustration of this step. Mount 8148 Dropplate ... only if required (see Page 5). Install closer with power adjustment shaft toward hinge edge of door. Note: If using full metal cover, cover mounting clips must be slipped under ends of closer when closer is being mounted. Clips should project 1/4” (6mm) beyond each end of closer.For suffix “H” only, check that hand of arm matches hand of door. See arm illustration on page 2 for location of arm handing mark. With door closed, closer valves ‘S’ and ‘L’. Then with a wrench, turn pinion shaft 50° or more to permit proper alignment of arm mark with pinion flat - ‘L’ for Left hand door. ‘R’ for Right hand door. See Arm Mounting Detail and Main Arm Installation at right below. (Caution: Closer arm is under spring tension and may be difficult to rotate.) Reopen valves ‘S’ and ‘L’ by turning counter clockwise. With door closed, align soffit plate with mounting holes in frame. Fasten soffit plate to frame with flat head screws provided.... use spacer blocks 2019S or 6891, if required. (Caution: Closer arm is under spring tension and may be difficult to rotate.)Make closer adjustments (see page 6) before installing cover ... NOTE: DO NOT back valves out of closer or a leak will result. Install cover (see page 6). NOTE: Architectural Covers 8400A and 8400MA CAN NOT be used with “PR” prefix closers that are installed for doors openings in excess of 120°.Installation Instructions
L
R
Y
S
Z
L
R
Y
S
Z
Power Adjustment ShaftPinion FlatArm MarkLeft Hand DoorDoor SwingMain Arm Installation InstructionsPower Adjustment ShaftPinion FlatArm MarkRight Hand DoorPR8101/ *PR8301/PR8501CLP8100/CLP8300/CLP8500Butt Hingesor Offset PivotsCenterPivots in. (mm)in.(mm)in.(mm)in.(mm) in.(mm)in.(mm)85°-90°90°-95°95°-100°100°-105°105°-110°110°-115°115°-120°120°-180°1-1/4(32)7(178)3-3/4(95)9-1/2(241)3-3/8(86)8-7/8(225)3-1/4(83)8-3/4(222)5-1/2(140)11(279)5-3/8(137)10-7/8(276)4-3/4(121)10-1/4(260)4-5/8(117)10-1/8(257)4(102)9-1/2(241)3-7/8(98)9-3/8(238)2-3/4(70)8-1/4(210)2-5/8(67)8-1/8(206)2-1/8(54)7-5/8(194)2(51)7-1/2(191)DimABABABInstallation Dimensions Chart* Series PR8500A, PR8500MA, and CAN NOT be installed for 120° to 180° door openings.

Copyright © 2007, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2209-020 (05-14)4
ASSA ABLOY
Standard FrameStandard MountSoffit PlateBlade Stop Mount2019S Block6891 BlockSoffit Plate5/8 Ref.(16)2-3/4(70)2(51)3/8(10)5/16*(8)1(25)2-1/16(52)7/16(11)*Use 9/16 (14) in openings with blade stops.CLHinge or Pivot12(305)3/4(19)3-1/4(79)BANarrow FrameSoffit Plate6890 Bracket6891 BlockSoffit Plate5/8 Ref.(16)2-3/4(70)2(51)3/8(10)1(25)2-1/16(52)7/16(11)CLHinge orPivot12(305)3/4(19)3-1/4(79)3/4(19)1-1/4(32)6890 Bracket2 to 2-3/4(51 to 70)BAFlush PartitionSoffit Plate2-1/2(64)1-1/2(38)1/2(13)3/4(19)CLHinge orPivot12(305)3/4(19)3-1/4(79)2019L AngleBracket1(25)BANotes:Do Not Scale Drawing.Left Hand Door Shown.Same dimensions apply for Right HandDoor measured from centerline of pivot point.Dimensions are in inches (mm).See Page 3 for A & B dimension values.

Copyright © 2007, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2209-020 (05-14)5
ASSA ABLOY
Standard FrameCLHinge or Pivot4(102)4(102)4(102)1-1/4(32)5/16(8)AFlush PartitionCLHinge orPivot1-5/8(41)5/16(8)4(102)4(102)4(102)ANarrow FrameCLHinge orPivot1-1/4*(32)5/16(8)4(102)4(102)4(102)*NOTE: This dimension must be taken from the same surface that the Soffit Plate is fastened to.A8148 Drop Plate Mounting HolesFriction Hold-Open Feature (”PR” prefixed units only) Hold door open to opening angle desired and tighten holder-adjustment-nut (wrench supplied) or use 1” Box or Open End wrench.The Thumbturn Hold-Open feature is controlled by the knob located on the arm of the unit. Turning this knob clockwise will engage the Hold-Open mechanism and increase the Hold-Open force. Turning this knob counterclockwise will reduce the Hold-Open force and disengage the Hold-Open mechanism.
Thumbturn Hold-Open Feature (”CLP” prefixed units only)
Thumbturn Action(Units suffixed “T”)DECREASE - - INCREASE8148 Drop Plate8148 Drop Plate8148 Drop Plate2019L Bracket6890 Bracket

Copyright © 2007, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited. 80-9380-2209-020 (05-14)6
ASSA ABLOY
Closing Power Adjustment (8X01 closers only –Using “Power Adjustment Chart” from Page 3, select the correct number of turns for power adjustment shaft that corresponds with the installation. With 1/8” hex-key provided, rotate adjustment shaft full 360° clockwise turns to desired setting. After closer has been installed and proper adjustments made to the sweep and latch, it may be necessary to readjust spring power for good closing action.Control Valve Adjustments(See Figure 2.)Closing Speed Controls (Figure 1A or 1B and 2.) Valve “S” Controls Sweep Range. Valve “L” Controls Latch Range. Valve “D” Controls Delay Range (optional). Unit Adjustment
H
C
T
A
L
H
C
T
A
L
Delayed ActionClosing Cycle1BClosing Speed Controls Figure 1.
W
E
E
P
S
P
E
E
W
S
Attention : Adjust Closing Speed Time to between 4 to 7 seconds from 90°. Use of the door by handicapped, elderly or small children may require greater closing time.CLOSEDCLOSEDStandard Closing Cycle1A
D
E
L
A
Y
R
A
N
G
E
10°10°70°
CAUTION:DO NOT BACK VALVES OUT OFCLOSER OR A LEAK WILLRESULT.
Closing Speed Controls Figure 2. Slow 1/8”HexKey Fast LatchValve SweepValve Delay ValveClosing Power Control Figure 3.Opening Cycle “Backcheck” valve controls the strength of cushioning in Backcheck Range. NEVER close this valve completely – it is not to provide a positive stop. (see Figure 4 and Figure 5).Cover–Full cover: Slide cover insert into the un-used cutout in cover. Install cover using screws provided.Narrow cover: Install cover using screws provided. Install pinion cap onto pinion shaft by hand or with a Phillips screw driver - DO NOT OVER TIGHTEN.Metal cover: Fasten cover to mounting clips with screws provided.Architectural Metal Cover: Remove cover insert where pinion is located. Install standoffs in ends of closer. Install cover using screws provided.Architectural Plastic Cover: Slide cover insert into the un-used cutout in cover. Install standoffs in ends of closer. Snap cover over standoffs.. Slow 1/8”HexKey Fast Slow 1/8”HexKey Fast
G
N
I
N
E
P
O
Opening Door Control Figure 4. Opening Cycle
B
A
C
K
C
H
ECK
CAUTION:DO NOT BACK VALVE OUT OFCLOSER OR A LEAK WILLRESULT.
Decrease IncreaseBackcheck Control Figure 5. Backcheck Valve* 1/8”HexKey Decrease Increase Power Adjustment ShaftNOTE: Maximum of 20 360° turns of Power Adjustment ShaftNEVER CLOSE VALVES COMPLETELY - NOT INTENDED TO PROVIDE A POSITIVE STOP.Cover Mounting Figure 6. 5/16” Socketor Adjustable Wrench
3000 Highway 74 East • Monroe, NC 28112Tel: (877)- • Fax: [phone]-2255www.nortondoorcontrols.com
ASSA ABLOY