Assa Abloy Corbin Russwin ED8200A Series User manual

FM124B 04/20
Installation Instructions
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
ED8200A Series
For Wood and Metal Doors
Fire-Rated Rim Exit Device

2
ED8200A Series
Installation Instructions
Fire-Rated Rim Exit Device
FM124B 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
1 Determine Hand of Door
IMPORTANT
• Failure to follow these instructions could affect
operation of this product and void warranty.
• Some trim designs are handed when used with this
device (see trim instructions).
• Exit devices must be securely fastened to properly
reinforced doors with fasteners which will not loosen or pull out. Add reinforcement when necessary.
• Before Installing:
• Be sure exit device is the proper hand for your door. (Figure 1)
• Use enclosed template to ensure proper operation.
Figure1
Push side
Pull sideLeft Hand
Reverse
Bevel Door
Right Hand
Reverse
Bevel Door
TOC Table of Contents
1 Determine Hand of Door ........................................................2
2 Package Contents ...............................................................3
3 Preparation .....................................................................3
a Mark Horizontal Centerline of Device ............................................3
b Install Trim (If Furnished) ........................................................3
c Cut Pushbar (If Required)........................................................4
4 Installation ......................................................................5
a Mount ED8200A Exit Device .....................................................5
b Install Strike .....................................................................6
c Install Front Bar Insert, Rear & Front Covers ......................................6
d Test Pushbar.....................................................................7

3
ED8200A Series
Installation Instructions
Fire-Rated Rim Exit Device
FM124B 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
2 Package Contents
ED8200A Qty. Description
Latch Assembly 6 #12-24 x 7/8" Phillips flat head machine screws
Rear Bracket 2
#12-24 x3/4" Phillips pan head machine screws, and #12 internal
washers (wood doors #12 x 1-1/4" Phillips pan head, type A, tapping
screws)
Strike, UL 4 #12-24 x 7/8" Phillips flat head machine screws
Front Bar Insert 1 #8-32 x 1" Phillips pan head machine screw
Rear Cover 1 #8-32 x 1" Phillips flat head machine screw with external washers
Front Cover 2 #8-32 x 1/2" Phillips flat head machine screw, type F, with external
washers
Non-Reinforced Door 4 #12-24 x 1-21/32" sex nuts
3 Preparation
a Mark Horizontal Centerline of Device
Establish a centerline of device by drawing a line across the door and the door stop, 40-5/16" (1.02 m)
above finished floor unless doors have been pre-prepped. (Figure 2)
b Install Trim (If Furnished)
See separate trim installation instructions.
Figure2
Of Device
Door
Finished
Floor Line
40-5/16"
(1.02 m)
Jamb
Of Strike

4
ED8200A Series
Installation Instructions
Fire-Rated Rim Exit Device
FM124B 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
3 Preparation (cont.)
c Cut Pushbar (If Required)
Note
If bar does not require cutting, proceed to step 4a.
A. Installation of device depends on trim: Note 3/4" (19 mm) minimum restriction. (Figure 3)
B. Measure and mark bar as shown. (Figure 4)
C. Fully depress bar and cut off square on mark. (Figure 5)
Figure3 Figure4
3/4" (19 mm) Min.
Cut off point
Door width minus
5" (127 mm)
Pushbar
must
be fully
depressed
Figure5

5
ED8200A Series
Installation Instructions
Fire-Rated Rim Exit Device
FM124B 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
4 Installation
a Mount ED8200A Exit Device
Installation of device depends on trim:
A. For Reinforced Metal Doors:
• For throughbolted trim in 2-1/8"prep, install device with two (2) fillister head screws (packed
with trim) in latch assembly holes marked D. (Figure 6)
For all other applications, install device with two (2) pan head machine screws and two (2)
internal tooth lock washers in latch assembly holes marked C.
• Use level as shown to ensure device is level. Use rear bracket to spot, drill, and tap two (2) rear
bracket mounting holes. Attach rear bracket to door using two (2) pan head machine screws and
two (2) lock washers. Drill, tap, and install four (4) flat head machine screws in latch assembly
holes marked E. (Figure 6)
B. For Un-Reinforced Doors Only:
• Using device as a template, drill 1/4"(6 mm) top and bottom latch assembly holes marked D
though door. Enlarge holes to 3/8"(10 mm) from opposite side of door to clear for sex nuts. Install
two (2) flat head machine screws and two (2) sex nuts. Drill and tap two (2) middle latch assembly
holes marked Eand install two (2) flat head machine screws (if applicable). (Figure 6)
C. For All Other Door Types:
• For throughbolted trim in 2-1/8"prep, install device with two (2) fillister head screws (packed
with trim) in latch assembly holes marked D. (Figure 6)
For all other applications, install device with two (2) pan head machine screws and two (2)
internal tooth lock washers and two (2) sex nuts in latch assembly holes marked C.
• Use level as shown to ensure device is level. Use rear bracket to spot and drill 1/4"(6 mm) holes
through door. Enlarge holes to 3/8"(10 mm) from opposite side of door to clear for sex nuts and
bolts. Attach rear bracket to door using two (2) pan head machine screws, two (2) lock washers,
and two (2) sex nuts. (Figure 6)
Figure6
Sex Nuts
Level
Rear
Bracket
Lock
Washer
Pan
Head
Machine
Screw
Flat Head Machine Screw
Of Device
Stop Line
Latch
Assembly
E
C
C
D
D
E
E
E
Sex Nuts
IMPORTANT
Maintain a 1/16" (2 mm) gap
between stop and latch frame.

6
ED8200A Series
Installation Instructions
Fire-Rated Rim Exit Device
FM124B 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
4 Installation (cont.)
b Install Strike
Install strike using flat head machine screws in
holes marked A. (Figure 7) Adjust strike. Strike is
properly adjusted when latch is able to fully project
when door is closed. Drill, tap, and install two (2) flat
head machine screws in holes marked B. (Figure 7)
Tighten all screws.
c Install Front Bar Insert, Rear & Front Covers
A. Slide front bar insert over end of front bar.
B. Assemble 1/2" pan head tapping screw through insert mounting hole.
C. While holding insert flush against back edge of front bar, tighten screw to bottom of recessed
mounting hole.
D. Install front and rear cover using 1" flat head screw with attached washer. (Figure 8)
Figure8
Flat Head
Machine
Screw
1" Flat Head Screw
with Attached Washer
1/2" Pan Head Tapping Screw
Front
Cover
Back
Edge
Assembled View
Front Bar
Front Bar
Front Bar Insert
Front Bar
Insert Rear
Mounting
Bracket
Rear Cover
Rear Cover
Figure7
Flat Head
Machine
Screw
Strike
Shim Door
A
A
B
B

7
ED8200A Series
Installation Instructions
Fire-Rated Rim Exit Device
FM124B 04/20
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
d Test Pushbar
Latchbolt is retracted by pushbar inside. If latchbolt does not operate properly or does not remain secure,
inspect dimensions outlined in steps 3c, 4a, and 4c.

Corbin Russwin is a brand associated with ASSA ABLOY Access and Egress Hardware Group, Inc., an ASSA ABLOY Group company.
Copyright © 2011, 2020 ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole or in part
without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
Phone: [phone]
Fax: [phone]
www.corbinrusswin.com
FM124B 04/20