Assa Abloy Corbin Russwin DC3210 Series User manual

80-9330-3003-152 04/18
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
DC3210 Series
Important
• An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void
product warranty.
• To avoid personal injury, DO NOT DISASSEMBLE THIS DOOR CLOSER BODY.
• Door closers must be securely fastened to a properly reinforced door and frame with fasteners provided.
• Door closers with a HOLD OPEN ARM are not permitted to be installed in fire door assemblies.
• Door and frame must be specifically templated for 85°, 90°, 95°, 100°, 105° orb 110° door swing.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
A11 or A12 Heavy Duty Spring Stop Parallel Arm

2
80-9330-3003-152 04/18
DC3210 Series Closer
Installation Instructions
A11 or A12 Heavy Duty Spring Stop Parallel Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
RHR LHR
A11-Non-Hold Open Arm
STANDARD APPLICATION
WITH 615F58 BRACKET
DEEP REVEAL APPLICATION WITH
M103 OPTION(615F59 CLAMP KIT)
FLUSH PARTITION APPLICATION
WITH
M104 OPTION (615F60 BRACKET)
A12 - Hold Open Arm
1 Introduction
L
3/8
(10)
1/4-20 THREAD
Drill thru 9/32 (7.1) Enlarge to
3/8
(9.5) Dia. This Side Only
(4 Places)
DOOR
THICKNESS
SEX NUT
LENGTH “L”
1-3/8" (35mm)
1--3/4" (44mm)
&OVER
1-9/32" (33mm)
1-21/32" (42mm)
MOUNTINGSCREW SPECIFICATIONS
ARM AND CLOSER BRACKET
}
or{Option M54:
Sex nuts, furnished
when ordered
1/4-20 oval head machine
screw or 1/4-14 self-drilling
screw Type BSD. 3/16 (4.8)
diameter pilot hole required
forWood Applications.
L
3/8
(10)
1/4-20 THREAD
Drill thru 9/32 (7.1) Enlarge to
3/8 (9.5) Dia. This Side Only
(4 Places)
DOOR
THICKNESS
SEX NUT
LENGTH “L”
1-3/8" (35mm)
1--3/4" (44mm)
&OVER
1-9/32" (33mm)
1-21/32" (42mm)
MOUNTINGSCREW SPECIFICATIONS
ARM AND CLOSER BRACKET
}
or{Option M54:
Sex nuts,
furnished
when ordered
1/4-20 oval head machine
screw or 1/4-14 self-drilling
screw Type BSD. 3/16 (4.8)
diameter pilot hole required
forWood Applications.
Figure 1

3
80-9330-3003-152 04/18
DC3210 Series Closer
A11 or A12 Heavy Duty Spring Stop Parallel Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Introduction
**NOTE: These forces are for standard templating with bearing type hinges and do not account
for pressure differentials and draft.
*Dimension “C” is only used for Flush Partition application (Frame Template 1C)
Opening
Doors 28" to 32"
615F52 NHO Arm (A11)
615F51 HO Arm (A12)
Doors 33" to 41"
615F54 NHO Arm (A11)
615F53 HO Arm (A12)
Doors 42" to 48"
615F56 NHO Arm (A11)
615F55 HO Arm (A12)
HOLD
OPEN
DEAD
STOP DIM. A DIM. B *DIM. C DIM. A DIM. B *DIM. C DIM. A DIM. A *DIM. C
85° 90° 11
(279)
10
(254)
10-1/8
(257)
13-1/8
(333)
12-1/4
(311)
12-3/8
(314)
15-1/8
(384)
14-3/8
(365)
14-1/2
(368)
90° 95° 10-1/2
(267)
9-1/2
(241)
9-5/8
(244)
12-5/8
(321)
11-5/8
(295)
11-3/4
(298)
14-1/2
(368)
13-3/4
(349)
13-7/8
(352)
95° 100° 10
(254)
9
(229)
9-1/8
(232)
12
(305)
11-1/8
(283)
11-1/4
(286)
13-7/8
(352)
13-1/8
(333)
13-1/4
(337)
100° 105° 9-1/2
(241)
8-1/2
(216)
8-5/8
(219)
11-5/8
(295)
10-5/8
(270)
10-3/4
(273)
13-1/4
(337)
12-1/2
(318)
12-5/8
(321)
105° 110° 9
(229)
8
(203)
8-1/8
(206)
11
(279)
10-1/8
(257)
10-1/4
(260)
12-3/4
(324)
12-1/8
(308)
12-1/4
(311)
110° 115° 8-1/2
(216)
7-1/2
(191)
7-5/8
(194)
10-1/2
(267)
9-1/2
(241)
9-5/8
(244)
12-1/4
(311)
11-1/2
(292)
11-5/8
(295)
Size of Door & Door Closer
Type of
Installation Interior Exterior In-swinging
Exterior
Out-swinging
Recommended
Closer Size
**Max. Opening Force
lbs/f
Parallel Arm
2' 4" - - 1 8
2' 6" - - 2 14
3' 0" - 2' 6" 3 16
3' 6" - 3' 0" 4 22
4' 0" - 3' 6" 5 24
4' 6" - 4' 0" 6 26
SEE CHART TO SELECT DEGREE OF DOOR OPENING AND DOOR WIDTH FOR YOUR DOOR.
THEN, DETERMINE FRAME CONDITION: STANDARD & DEEP REVEAL (use Dim’s. A & B) or FLUSH
PARTITION (use Dim’s A & C)

4
80-9330-3003-152 04/18
DC3210 Series Closer
Installation Instructions
A11 or A12 Heavy Duty Spring Stop Parallel Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
1. Template
Mark door and jamb (for closer bracket and arm
brackets).
Frame Template 1A (Standard Application with
615F58 Bracket) (Figure 2)
For Deep Reveal: Frame Template 1B. (Figure 3)
For Flush Partition: Frame Template 1C. (Figure 4)
1/2
(12.7)
2-3/4
(70)
FRAME STOP
TOPOF DOOR
C
L
HINGE
OR
PIVOT
DOOR
FRAME STOP
2-3/4
(70) 3/8
(9.5)
2
(50.8)
7/16
(11.1)
CLOSER
BRACKET
1
(25.4) 4-5/16
(109.5)
B
A
TYP.
1-3/8
(35)
1-1/4
(31.8)
1-1/8
(29)
3/4
(19)
REVEAL 615F58
BRACKET
615F58
BRACKET
Frame Reveals 1-7/8 to 4-5/8
(48mm to 117mm)
""
Reveal
Door
615F58
BRACKET
Door Preparation is Typical for
all Frame Templates
1A, 1B, and 1C
NOTES:
• Check hand of door. (Figure 1)
• Right Hand Application Shown, Left Hand
Opposite
• Dimensions given in inches (mm).
Do Not Scale Drawing.
• Closer must be installed in a true
horizontal plane to ensure proper closer
performance.
Figure 2

5
80-9330-3003-152 04/18
DC3210 Series Closer
A11 or A12 Heavy Duty Spring Stop Parallel Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
2. Install Closer Bracket. (Figure 5)
1/2
(12.7)
C
L
HINGE
OR
PIVOT
DOOR
FRAME STOP
2-3/4
(70)
3/8
(9.5)
2
(50.8)
7/16
(11.1)
B
TYP.
1-3/8
(35)
REVEAL
5/16
(8)
2-1/8
(54)
4-3/8
(69.9)
615F59
CLAMP (TYP)
Door
Door
Clamps with Spacer
Clamps Only
SPACER
FRAME TEMPLATE 1B DEEP REVEAL APPLICATION with M103 OPTION (615F59 CLAMP KIT)
FRAME TEMPLATE 1C FLUSH PARTITION APPLICATION with M104 OPTION (615F60 BRACKET)
1-1/2
(38.1)
1/2
(12.7)
2-1/2
(63.5)
1-3/4
(44)
3/4
(19.1) CFrame Reveals 0to 1/8 (0mm to 3mm)
""
Reveal
Frame Reveals Over 4-5/8 (117mm)
"
DoorFrame
Reveal
Reveal
CLAMP
FRAME
FRAME
CLAMP
615F60
BRACKET
Pin Hole End
Countersunk Holes
Figure 3
Figure 4
Figure 5

6
80-9330-3003-152 04/18
DC3210 Series Closer
Installation Instructions
A11 or A12 Heavy Duty Spring Stop Parallel Arm
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Installation
3. Mount Closer Body to Closer Bracket.
(Figure 6)
4. Fasten Arm Brackets to Frame
For Frame Templates “1A” and “1B” fasten
main arm bracket to frame. Locate and install
reinforced brackets 615F58 (1A) or 615F59
Kit (1B).
For Frame Template “1C” fasten Flush
Partition Bracket 615F60 to frame face
and install main arm bracket to the 615F60
Bracket.
5. Connect Arm To Closer (Figure 7)
Using hex wrench provided, close (turn
clockwise) CLOSING SPEED VALVE. (Figure
9) DO NOT OVER TIGHTEN.
• Open door to approximately 60°
• Using wrench on underside of spindle,
rotate spindle approximately 135° toward
hinge edge of door.
• Install arm on spindle at an approximate 90°
angle to door.
• Reopen CLOSING SPEED VALVE.
• Install and tighten arm washer and screw.
Holding Pins
1/4-20 x 1/2 OHMS (2)
DOOR
SPINDLE
ARM
CENTERLINE
ALL ANGLES SHOWN ARE APPROXIMATE
DOOR
90°
SPINDLE
ROTATED 135°
Rotate 135°
SPINDLE AT REST
60°
DOOR
135°
WRENCH
90°
ARM
Figure 6
Figure 7

7
80-9330-3003-152 04/18
DC3210 Series Closer
A11 or A12 Heavy Duty Spring Stop Parallel Arm
Installation Instructions
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Adjustments
Adjustments (Figure 8)
(3/32 Allen Wrench Provided)
Closing Speed Valve (Figure 9)
To adjust speed of door closing from fully
open to a position 2 to 5" from closed, turn
Closing Speed Valve CLOCKWISE to SLOW
closing, COUNTER-CLOCKWISE to SPEED
closing.
Latching Speed Valve (Figure 10)
After closing speed has been obtained, turn
latching speed valve CLOCKWISE to SLOW
latching or COUNTER-CLOCKWISE to SPEED
latching for last 2 to 5 of door travel.
NOTE: Set combination of CLOSING and
LATCHING speeds to between 3 and 7
seconds Use of door by handicapped,
elderly or small children, may require
even greater closing time.
Backcheck Intensity Valve (Figure 9)
Turn valve COUNTER- CLOCKWISE to reduce
backcheck or CLOCKWISE to increase
backcheck. (Backcheck should be set to give
a soft cushioning action, not a sudden stop).
Delayed Action Valve (Figure 9)
Turn valve CLOCKWISE to SLOW closing,
COUNTERCLOCKWISE to SPEED closing.
Delayed action may be adjusted from 20
seconds to 90 seconds, depending on degree
of door swing. Delay occurs at the beginning
of the door closing cycle from fully open down
to 70°, where the closing speed valve then
begins its control.
Delayed Action
Option
M-71
Backcheck
Latch
Sweep
LATCHING
SPEED
VA LV E
Power
Size
Stamp
Date Stamp
BACKCHECK
INTENSITY VALVE
OPTION M71
DELAYED
ACTION VALVE
CLOSING
SPEED VALVE
SPRING POWER ADJUSTER
(5/16" WRENCH or SOCKET)
(FLAT TIP SCREWDRIVER)
Rotate
To Decrease
Hold Open
Force
To
Increase
Hold Open
Force
Hold Open
“On” Hold Open Force
HOLD OPEN ADJUSTMENTS - A12 ARMSONLY
Hold Open
“Off”
Figure 8
Figure 9
Figure 10
Figure 11

80-9330-3003-152 04/18
Copyright © 2018 Corbin Russwin, Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Corbin Russwin, Inc. is prohibited.
Patent pending and/or patent: www.assaabloydss.com/patents
Corbin Russwin
225 Episcopal Road
Berlin, CT 06037
Phone: [phone]
Fax: [phone]
corbinrusswin.com
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
3 Adjustments
Adjust Spring Power According to Chart
DC3200 Size 1-6 Adjustment (Figure 12)
• All DC3200 closers are factory set at an
approximate Size 3.
Full Cover(Standard)
Slim Cover (Option M76)
Figure 12
Figure 13
Size of Door No. of Full (360°)
Turns Clockwise of
Power Adjuster
Equivalent Closer
Size (Approx.)
Interior Exterior
In-Swinging
Exterior
Out-Swinging
2' 4"
(712)
2' 6"
(764) - 4 2
2' 6"
(764)
3' 0"
(915) - 8 3
3' 0"
(915)
3' 6"
(1067)
2' 6"
(764) 12 4
3' 6"
(1067)
4' 0"
(1219)
3' 0"
(915) 16 4
Figure 14
4 Cover Installation
Full Cover(Standard)
Slim Cover (Option M76)
Install Cover (Figure 13)
Slip cover over closer. Hold tightly against
closer mounting surface. Secure on each
side with 6-32 x 1/4 PBHMS screws.
Slim Cover Option M76 only (Figure 14)
Position spindle cap over unused spindle
and secure with truss head screw.
• Adjust closer as necessary for door size
using this chart.
• Readjustment may be required to suit
prevailing conditions.