Assa Abloy Yale Real Living Assure Lock YRD426 User manual

P/N YRL-TSINSTL-FUL Rev G
1
® ®
Yale Assure Lock
Touchscreen Deadbolt
Installation and Programming Instructions
(YRD226/YRD426)
®
x3
#8-32 x 5/16"
Machine screws
x4
#7 wood & #8-32
machine x 20mm
Combination screws
x2
M6x59.5mm
Long through bolt
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE PRODUCT AND VOID THE FACTORY WARRANTY
Optional
Network Module
Before you begin
for step-by-step installation
instructions & to register
your product
DOWNLOAD
THE BILT APP

P/N YRL-TSINSTL-FUL Rev G
2
Preparing Door

P/N YRL-TSINSTL-FUL Rev G
3
Optional Fire Kit Parts
For Model YRD620 ONLY
Installing Optional Fire Cup
Inside of Door
O
optional
O
optional

P/N YRL-TSINSTL-FUL Rev G
4
O
x4
1
defaut
2-3/8" position
2-3/4" position
Installing Latch & Strike Plate
Press
Pull
optional
Bolt must be in retracted
(unlocked) position. Note
horizontal orientation of
mechanism.

P/N YRL-TSINSTL-FUL Rev G
5
2Installing Touchscreen Escutcheon
Outside of DoorInside of Door
Bolt must be in retracted (unlocked)
position. Note horizontal orientation
of mechanism.
O
optional

P/N YRL-TSINSTL-FUL Rev G
6
x2
3Installing Interior Mounting Plate
Loosen screw to
remove cover.
O
optional

4Attaching the Cable Assembly
P/N YRL-TSINSTL-FUL Rev G
7

P/N YRL-TSINSTL-FUL Rev G
8
x3
5Installing Interior Escutcheon

3
Testing Operation
Bolt must be in retracted
(unlocked) position before
installing batteries.
P/N YRL-TSINSTL-FUL Rev G
9

P/N YRL-TSINSTL-FUL Rev G
10
2
Testing Operation

P/N YRL-TSINSTL-FUL Rev G
11
6Installing Optional Network Module

P/N YRL-TSINSTL-FUL Rev G
12
7Installing Batteries & Cover
Continue with Programming Instructions to customize your product.
® ®
Congratulations, you've installed the Yale Assure Lock
Touchscreen Deadbolt (YRD226/YRD426)!
Tighten screw
to replace cover.
"Welcome to
Yale Real Living."

Programming Instructions
OR
Master PIN Code must be created before any further programming.
Max User Codes = 250 with Z-Wave Plus or ZigBee network module
Max User Codes = 25 without network module or with iM1 network module
Nax User Codes = 12 with Bluetooth
Interior Escutcheon
Privacy
Mode
Button
Speaker
"P" Key
(Return to Previous)
Low Battery
Indicator
Lockout
Mode
Exterior Escutcheon
P/N YRL-TSINSTL-FUL Rev G
13

1Creating a Master PIN Code must be performed upon installation or after resetting
the lock to factory default. Programming and use of lock is not possible until this
step has been successfully completed.
"Register Master
Code. Press the gear
key to continue."
"Enter a 4 to 8 digit
PIN code followed by
the gear key."
"Registered."
Enter 4-8
digit Master
PIN Code.
Press
Press
Creating Master PIN Code
P/N YRL-TSINSTL-FUL Rev G
14

2Creating User PIN Codes
Master PIN code must be created first.
*Max user codes = 250 with Z-Wave Plus or ZigBee network module
Max user codes = 25 without network module or with iM1 network module
Max user codes = 12 with Bluetooth
"Menu Mode,
enter number,
press the gear key
to continue."
Enter Master
PIN code
Press
Press
Press
Press
Press
Press
Enter 4-8 digit PIN code
Press
Enter 4-8 digit PIN code
Press
(code flashes)
Adding more *User Codes: To end programming:
Press
P/N YRL-TSINSTL-FUL Rev G
15

P/N YRL-TSINSTL-FUL Rev G
16
3
PIN Code Management (With Network Module - Up to 250 Users)
Master
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
User ___
Enter PIN Code
Press
Code Chart Duplicate if necessary
User Name
User Type PIN Code
Unlocking Door with PIN Code
User #

P/N YRL-TSINSTL-FUL Rev G
17
Interior Escutcheon
Resetting Lock to Factory Default
Reset
Button
5. Replace battery cover.
When lock is reset to factory defaults all user codes (including the
Master PIN code*) are deleted and all programming features are reset
to original default settings (see below).
3. The reset button (see image at right) is located beside the PCB
cable connector.
4. While pressing the reset button (minimum of 3 seconds) reinstall
batteries. Release reset button.
Upon reset, Master PIN Code creation is the only option available and
must be performed prior to any other programming of the lock.
1. Remove the battery cover and batteries.
2. Remove the interior escutcheon to access the reset button.

P/N YRL-TSINSTL-FUL Rev G
18
Factory Settings
*The Master PIN code must be registered prior to any other programming of the lock.
Registration required*
Settings Factory Setting
Master PIN Code
Automatic Re-lock Disabled
Lockout Mode Disabled
Language Setting English
Wrong Code Entry Limit 5 Times
Shutdown Time 60 Seconds
Volume Setting Enabled (Low)
Privacy Setting Disabled
One Touch Locking Enabled
Inside Indicator Light Disabled (Off)
Automatic Re-lock Time 30 Seconds
Escape Return Mode (Model YRD620 only) Disabled

P/N YRL-TSINSTL-FUL Rev G
19
Definitions
Shutdown Time: The unit will shutdown (flashing RED) for sixty (60) seconds and not allow operation after the
wrong code entry limit (5 attempts) has been met.
ZigBee network module is 250; without network module or with iM1 network module, maximum is 25; with
Bluetooth, maximum is 12. Note: When deleting user pin code(s), screen will display user pin code being deleted.
User PIN Code: The user code operates the lock. The maximum number of user codes with Z-Wave Plus or
Volume Setting Mode: The volume setting for PIN code verification is set to Low (2) by default; otherwise it can
be set to High (1) or Silent (3) for quiet areas.
Privacy Mode: Privacy mode is disabled by default. Enable Privacy Mode by pressing the privacy button for 4
seconds to put the lock in do-not-disturb mode (all pin codes are disabled).
Tamper Alert: Audible alarm sounds if attempting to forcibly remove outside lock from door.
Wrong Code Entry Limit: After five (5) unsuccessful attempts at entering a valid PIN code, the unit will shut
down and not allow operation for sixty (60) seconds.
One Touch Locking: When the latch is retracted, activating the keypad will extend the latch (during Automatic
Re-lock duration or when Automatic Re-lock is disabled). When One-Touch Re-lock is not in use (disabled), any
valid PIN code will re-lock the lock.
Previous: While in Menu Mode, pressing this icon cancels the current operation and returns the user to the
previous step.
All Code Lockout Mode: This feature is enabled by the Master code. When enabled, it restricts all user (except
Master) PIN code access. When attempting to enter a code while the unit is in Lockout, the RED locked padlock
will appear on the screen.
Network Module Setting: With the optional Network Module installed, this setting becomes available thru the
Main Menu (7) and allows the lock to connect with a network controller.
Language Setting Mode: Choosing English (1), Spanish (2) or French (3) becomes the (default) setting for the
lock's voice prompts.
Master PIN Code: The Master PIN code is used for programming and for feature settings. It must be created
prior to programming the lock. The Master code will also operate (unlock/lock) the lock.
Automatic Re-lock Time: After a successful code entry or manual unlock with the key, the lock will automatically
re-lock after each unlock in an effort to keep your home secure. This feature is optional, and can be turned off. In
the ON mode, the lock will automatically re-lock after thirty (30) seconds.
Low Battery: When battery power is low, the Low Battery Warning indicator flashes RED. If battery power is
completely lost, use the cylinder key override.
Inside Indicator Light: Located on the interior escutcheon. Shows active status (Locked) of lock and can be
enabled or disabled in the Advanced Lock Settings (Main Menu selection #3).

P/N YRL-TSINSTL-FUL Rev G
20
*The Master PIN code must be registered prior to any other programming of the lock.
Follow the voice commands.
Lock Response: "Menu mode, enter number, press key to continue."
2. Enter 4-8 digit master PIN code* followed by key.
3. Enter digit corresponding to the function to be performed followed by the key.
1. Touch screen with back of hand or palm to activate.
M
U
**This function appears only with
network module installed.
Default settings
in bold.
Master PIN Code Setting
User PIN Code Registration Continue
Complete
Register
Delete
Continue
Complete
M
23
1
Join the Network
Enable
Disable
English
Spanish
French
Silent
Low
High
Complete
Exit the Network
Volume Setting
Language Setting Mode
Lockout Mode
**Network Module Setting
Privacy Setting Mode Enable
Disable
Handing the Lock Preforms automatic
handing of the lock
Advanced Lock Settings Automatic Re-lock Disable
30 sec
Inside Indicator Light
One Touch Locking Enable
Disable
Enable
Disable
Continue
60 sec
3 min
2 min
Continue
Complete
Model YRD226 Feature Programming Through
Menu Mode Using Master PIN code*