Assa Abloy SARGENT Delayed Egress 57-80 Series User manual

1-800-727-5477 • www.sargentlock.com
A7743F 1/23
Installation Instructions
Delayed Egress 57-80 Series
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without the express
written permission of SARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in dam-
age to the product and void the
factory warranty.
WARNING

2
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
TOC Table of Contents
1 Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2 General Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 Component Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4 Cylinder Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Factory Default Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
6 DIP Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
7 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
8 Exit Device Plug-in Connector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
9 Sample Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
a Basic 57- Delayed Egress with Fire Alarm and Remote Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
b 57- Exit Device with inside Keypad, Fire Alarm, Door Status and Remote Horn . . . . . . . . . . . . . .16
c 57- Exit Device with Fire Alarm, Keypads and Fail Safe ET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
10 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
a Power Up Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
b Modes of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
11 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
a Diagnostic and Insert LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
b Rim, Mortise and Vertical Rod Exit Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
c Minimum Requirements for Arming Rail (Delayed Egress Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
d Symptom/Failure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
Warning
1
FCC:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada:
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des
règlements d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer
l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut
causer l’opération peu désirée.
“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.”
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than
that necessary for successful communication.
Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne
d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les
risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de
sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une
communication satisfaisante.
Any retrofit or other field modification to a fire rated opening can potentially impact the fire rating of the opening, and
SARGENT Manufacturing makes no representations or warranties concerning what such impact may be in any specific
situation. When retrofitting any portion of an existing fire rated opening, or specifying and installing a new fire-rated
opening, please consult with a code specialist or local code official (Authority Having Jurisdiction) to ensure compliance
with all applicable codes and ratings.

4
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
2General Description
The SARGENT 57-Delayed Egress Exit Device is designed to work with an external electromagnetic lock in areas that require a
delayed egress which alarms at the door when any attempt is made to violate the door. The 57- device can be tied into a fire
alarm system.
Note:
Proper connections and appropriate peripheral hardware are required.
BC-Prefix Option
The BC prefix for 57- indicates that the unit has been programmed to comply with the section of the BOCA code relating to
delayed egress.
BOCA allows for automatic reset of the delayed egress unit. Under BOCA, the unit can automatically reset thirty (30) seconds
after the door has been cycled. If the door is opened any time during the thirty (30) seconds, the timer in the unit resets and
waits another thirty (30) seconds before rearming. This requires a door position switch.
Note:
If a door position switch is not used (Blue wire connected to Black wire), the unit will automatically reset in 30 seconds.
Electrical Specifications
• Input Voltage: 24VDC +/- 15% (20.4 - 27.6VDC) regulated/filtered
• Power Consumption @ 24VDC (with 1584 Electromagnet):
• 60 mA (typical) Disarmed;
• 220 mA (typical, unloaded) Armed;
• 250 mA (typical) Delayed Egress Mode;
• 375 mA (max, loaded) with Optional Features
• Operating Temp: 0°C to 49°C (32°F to 120°F)
• Maximum Electromagnetic Lock load: 275mA. If desired load exceeds this limit, an external relay module may be used.
All components must be installed according to prevailing electrical codes.
There are no user serviceable parts on the 57- PCB module assembly.
Chassis
Cover
Insert
Assembly
Chassis
assembly
PCB Module
Assembly
Rail Assembly
Part Number Description
52-4830 PCB Module Replacement Pack - Standard
52-4831 PCB Module Replacement Pack - BOCA (BC prefix)
Consult factory Rail Assembly
Consult factory Chassis Assembly
Consult factory Insert Assembly
Consult factory Chassis Cover
2Parts Breakdown

5
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
3Component Installation
1. Determine locations of components at the door.
2. Mount all hardware and peripheral equipment according to manufacturer’s instructions.
Note:
For exit device mechanical installation, refer to mechanical instruction sheets and templates included with product.
• Power supply should be mounted near door to avoid power drop due to excessive wire runs.
• Features used will determine wire requirements of electric hinge or other power transfer.
0#
SARGENT
8
*
79
2
546
31 REMOTE RESET
(Optional)
Electromagnetic
Lock
Sample Elevation Diagram
24VDC Regulated
Power Supply
Indicates
number and size
of wires
120VAC
3-#14
KEYPAD
CARD READER
(Optional)
2-#18
4-#18
2-#18
2-#18
2-#18
*-#18
Junction
Box
(Others)
2-#18
Door Status
Switch (Optional)
Fire
Alarm
57-80 Series
Electroguard™
*Electric
Hinge

6
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
3Component Installation (Continued)
Verify hand and bevel of door. Exit devices are always reverse bevel and are mounted on the inside of the door.
Outside View
8800 RHRB shown
Lights from top to bottom:
Green, Red (Default)
Inside View
8800 LHRB shown
Lights from top to bottom:
Green, Red (Default)
Inside view
Left Hand
Reverse Bevel
Hinges Left
Open Outward
LHRB
Outside View
Right Hand
Reverse Bevel
Hinges Right
Open Outward
RHRB
On inside of door, exit devices are oriented as follows:
All subsequent illustrations in this document are shown as RHRB.

7
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
3Component Installation (Continued)
ElectroLynx®Connector System Notes
The system is designed to be installation friendly with pluggable connectors from the electric hinge through the
door to the rail. The only wiring required is to the flying leads on the pigtail harness assembly on the frame side of
the electric hinge.
Important:
The plug and receptacle connectors are designed to mate and lock together as shown in the figure. Plug the connectors onto
each other with the locking mechanism aligned as indicated.
Do NOT force connectors on any other way
Plug
Locking
Mechanism
Receptacle
57- Exit Device - ElectroLynx Wiring Notes (Consult factory for assistance if required)
• The ElectroLynx connector system is designed to be installation friendly with pluggable connectors
from the electric hinge through the door to the rail. The rail, raceway, electric hinge, and pigtail harness
connector terminations and wire colors all match.
• For most applications, an 8-pin electric hinge is required.
• Plug raceway connectors into ElectroLynx hinge connectors. Hard wire to corresponding pigtail harness
wires as required.
Installation Notes:
• With new applications, a raceway harness with 8- and 4-pin connectors will be pre-installed inside the
door by ASSA ABLOY door manufacturer when specified during the ordering process. Raceway harness
kits are also available for retrofit applications. (For retrofit applications, refer to retrofit instructions.)
• If door does not have a raceway harness with connectors, either consult factory for raceway retrofit kit or
cut connectors off product and hard wire, as required.
• Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail
connector ( - +) terminations and wire colors all match.

8
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
4Cylinder Installation
1. Prepare door according to template(s) and instructions supplied with exit device.
2. Verify cylinder (size varies; consult factory) is installed in rail insert with collar prior to installing exit device on
door.
Top View of Insert
Side View of Insert
Remove and Replace Cylinder
1. Ensure power is disconnected.
2. Loosen set screw by turning counter-clockwise using
5/64” allen wrench.
3. Extract and slide cylinder through spring and collar.
Note:
When replacing cylinder, slide cylinder through spring then collar,
taking care to orient cylinder as shown. Hold cylinder into proper
position and slowly tighten set screw until cylinder is securely held
by set screw. Do NOT overtighten set screw.
Set Screw
Collar
Spring
Cylinder with Key
Cylinder Orientation
See illustration on circuit board for correct orientation of
cylinder when installing.
Note:
The proper position of cam allows for removal of key.
Top View with cylinder removed
Illustration (on circuit board)
Bottom of Cylinde
r
Cylinder Cam
Top of Cylinder

9
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
5Factory Default Settings
After verifying the factory default settings for the DIP
switch, install the insert assembly to the rail assembly.
If default feature settings need to be changed, carefully
slide the insert assembly from the rail assembly to
make the proper DIP switch adjustments.
For example, solid RED can be set to indicate that the
rail is ”Armed” with solid GREEN indicating that rail is
”Disarmed”.
Note:
Use caution when removing insert assembly to avoid
damaging the rail harness connected to the PCB module
assembly.
OFF
ON
S2
Default factory presets for the 57- are as follows:
Status LEDs/Time Horn
Armed (Delayed Egress) Solid GREEN Off
Momentary Egress (Passage Delay) Flashing RED for 5 seconds Off
Disarmed Solid RED Off
Alarm Flashing RED and GREEN 15 seconds for egress On
Nuisance Delay 1 second On
Nuisance Audible On
Momentary Egress Time 5 seconds
Reverse LED RED (Armed)
Handing “Top” LED (Armed) for LHRB or RHRB

10
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
6DIP Switch Settings
S2-1 Nuisance Delay (Field selectable 0 or 1 second)
A one second nuisance delay can be enabled by setting Dip Switch (S2-1) to the “On”
position. When nuisance delay is enabled, the unit will require the push bar to be
depressed for more than one second in order to trigger an irreversible alarm condition.
If the push bar is released before the 1 second has elapsed, the unit will go back into
the “delayed egress mode” and the alarm will not sound. Nuisance delay is set to “On”
position at factory.
If the Dip Switch S2-1 is in the “Off” position, there will be no nuisance delay and alarm
horn will sound immediately when the push bar is depressed.
S2-2 Nuisance Audible (Field selectable on or off)
An audible horn is enabled by setting Dip Switch S2-2 to the “On” position. The internal
horn will sound as soon as the push bar is depressed, signaling that the device is armed. If
the pushbar is held down for more than 1 second, an irreversible alarm condition begins.
If Dip Switch S2-2 is in the “Off” position, the horn will not sound during nuisance delay.
Nuisance audible is set to “On” position at factory to sound horn when rail is depressed
during nuisance delay.
S2-3 & S2-4 Momentary Egress Time
Used to select the momentary egress time of 5, 10, 20 or 40 seconds. This switch is preset
at the factory for five seconds.
S2 DIP Switch position Momentary Egress Time
S2-3 S2-4
OFF OFF 5 seconds (default)
OFF ON 10 seconds
ON OFF 20 seconds
ON ON 40 seconds
S2-5 Reverse LED (Field selectable green or red)
When S2-5 is “Off” the exit device LED is green when in armed mode (default) and red
when in maintained or momentary egress mode. When S2-5 is “On” the exit device LED is
red when in armed mode and green when in maintained or momentary egress.
S2-6 Handing (Field selectable LHRB or RHRB)
For a LHRB exit device S2-6 is “Off” for the top LED on the insert to be used when the
device is armed. For a RHRB exit device S2-6 is “On” for the top LED on the insert to be
used when the device is armed.
OFF
ON
123456
S2-1
ON - 1 second Nuisance Delay
OFF - No Nuisance Delay
OFF
ON
123456
S2-2
ON - Nuisance Audible On
OFF - Nuisance Audible Off
OFF
ON
123456
S2-3 S2-4
ON - Red (Armed); Green (main-
tained or momentary egress)
OFF - Green (Armed); Red (main-
tained or momentary egress)
OFF
ON
123456
S2-5
ON - RHRB; Top LED indicates “Armed”
OFF - LHRB; Top LED indicates “Armed”
OFF
ON
123456
S2-6

11
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
7Wiring
Caution:
Disconnect all input power before beginning installation to prevent electrical shock and equipment damage.
Important:
• Installer must be a trained, experienced service person
• All wiring must comply with applicable local electrical codes, ordinances and regulations
• Field cut rail assemblies are not allowed. Exit device must be ordered for specific door width.
Installation Notes:
1. With new applications, a raceway harness with 8 & 4-pin connectors will be pre-installed inside the door by
ASSA ABLOY door manufacturer when specified during the ordering process. Raceway harness kits are also
available for retrofit applications. (For retrofit applications, refer to retrofit instructions)
2. If door does not have a raceway harness with connectors, either consult factory for raceway retrofit kit or cut
connectors off product and hard wire, as required.
3. Wiring to pigtail harness is per facility wiring requirement. The rail, raceway, electric hinge and pigtail
connector ( - +) terminations and wire colors all match.
4. **55- only (option) Switch contact rating: 2A @ 30VDC.
5. Tape or cap off ends of unused pigtail wires (not shown) to ensure that they do not short.
Electroguard (57-, 19-57-)
80 Series Rail
Ground ring terminal
4, Green (EG)
8
7
6
5
4
3
2
1
1, Black (-Return)
2, Red (+24)
3, *White RR
5, Orange (EI)
6, Blue (DS)
7, Brown (Mag-)
8, Red (Mag+)
4
3
2
1
2, Blue (C)
3, Brown (NO)
4, Yellow (NC)
Legend:
EI - External Inhibit
DS - Door Status Switch
EG - Earth Ground
NO - Normally Open
NC - Normally Closed
RR - Remote Reset
C - Common
* White wire on previous Legacy product was used as
Fire Alarm input option and has been replaced with RR.
** 55- only option

12
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
7Wiring (Continued)
The following are the input and output connector designations.
Harness Connector
PIN No.*
Circuit Board
PIN No.
Input/
Output
Harness
Wire Color Function
8-2 J1-1 input Red +24VDC power
8-1 J1-2 input Black -Return
8-3 J1-4 input White Remote reset
8-5 J1-5 input Orange External inhibit - disarm unit from
i/s or o/s (key switch, card reader, keypad)
8-6 J1-6 input Blue Door position sensor (Door Status/Monitor)
8-4 Chassis Ground Green ESD (Earth) Ground
8-7 J1-8 output Brown -Return Magnet -
8-8 J1-10 output Red +24VDC Magnet
*Example: 8-2 is the 8-pin connector position #2.
N.O.
N.O. N.C.

13
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
7Wiring (Continued)
Harness Connector
PIN No.*
I/O Circuit
Board PIN No. Function
8-2 J1-1
24VDC Power Supply Input (+)
This input may be tied to the normally closed contact of a building’s fire alarm system.
If the fire alarm is activated, this contact will open, voiding the 15 second delay for
egress.
8-1 J1-2 Return - Power Supply -return (-).
8-3 J1-4
Remote Reset - This input may be tied to a momentary normally open contact at a
remote location to reset the device when in alarm. Additionally when the device is
armed this input may be used for momentary egress with the time per the DIP switch
settings.
Note:
Previous Fire Alarm Input option has been replaced with Remote Reset.
8-4 Chassis
Ground
Chassis Ground - The chassis ground wire must terminate at earth ground of the
equipment power supply or the main power source.
8-5 J1-5
External Inhibit Input - Used to provide remote override of the delayed egress when
in the armed condition. Most common external inhibits are: card readers, keypad, key
switches, or remote control console. More than one external inhibit device must be
wired in parallel.
8-6 J1-6
Door Position Sensor - An external door status switch can be connected to the 57- to
provide additional security. If the door status switch is utilized, an irreversible alarm
will sound if the door is forced open while the device is armed.
Unit will not arm if door is not shut. Once the irreversible alarm sounds, it will have to
be reset at the door. If the door status switch is not utilized, connect the Blue wire to
Return (Black wire) of the 5-pin harness.
8-7 J1-8 Return Magnet -
8-8 J1-10
+24VDC Output Magnet
External Magnet Connection - This output can supply up to 275mA load to an
external magnet. This output may be connected to a 24VDC relay module if load shall
exceed 275mA.

14
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
8Exit Device Plug-in Connector Installation
Note:
No field rail cutoff allowed. Exit device must be ordered for specific door width.
1. Mount exit device per instruction sheet provided.
To insure trouble free operation, check that the push rail can be fully depressed. On vertical rod exit devices,
check that the latch bolts do not go into hold back position until the push rail is fully depressed.
2. Plug rail connector into raceway connector then feed through 1” hole in door. Install rail mounting bracket
with two screws supplied. Install rail end cap.
3. Plug raceway connector into electric hinge connector then feed through door prep. Mount electric hinge to
door.
4. Go to Aif wiring now. Go to Bif wiring is to be done later.
A. Refer to sections 8 and 9. Wire loose frame side wires to loose wires on pigtail harness as required using
connectors allowed by local code. Plug pigtail harness connector into electric hinge connector. Feed
harnesses through frame prep and mount electric hinge. Refer to operating instructions in section 10.
Apply power and test exit device.
B. Plug pigtail harness connector into electric hinge connector. Feed harnesses through frame prep and
mount electric hinge.
Pigtail harness
assembly with
8-pin connector
4 1
2 57- 80 Series Rail
with 8-pin connector
3
Electric Hinge with
8-pin hinge connector
Raceway harness with
8 & 4-pin connectors.
The 4-pin connectors are not
used here.
Mounting
bracket
1” dia. hole
in door
Screw
locations
Ring terminal
(from harness)
Insert bracket mounting screw through *ground
ring terminal. Fasten mounting bracket with
mounting bracket screws (ring terminal).
*Ring terminal must be grounded as indicated.
!

15
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
9Sample Wiring Instructions
aBasic 57- Delayed Egress with Fire Alarm and Remote Reset
During a fire alarm condition, the fire alarm contact opens which de-energizes the rail magnet and allows
immediate egress.
N.O.
7, Brown, Mag (-)
8, Yellow, Mag (+)
1584
Electromagnetic
Lock
Black (-)
Red (+)
24VDC 1.0AMP Regulated and Filtered Power Supply
110-120 VAC
Voltage adjust
for battery
backup
HOT
NEUT
GND
123
AC F
Low voltage AC
From transformer
AC
DC DC
Output
Plug pigtail harness
connector into8-pin
hinge connector at
frame side of door
NOTE: This drawing shows the
BPS Series. The PM Series
has no line voltage input, fuse
or connector to power on LED.
2.5 AMP polyswitch breaker
Red
Black
Unconnected
terminal
for switch
hookup
Raceway harness with 8 & 4-pin
connectors. The 4-pin connector
is not used here.
Battery Pack
Red
(+24), 2
Normally Closed Fire
Alarm Contact
(If Required)
Black
(- Return), 1
Green (EG), 4
57- 80 Series Rail with 8 &
4-pin connectors The 4-pin
connector is not used here
Note: Typical raceway location
is shown. Other locations may
exist depending on door type
8
7
6
5
4
3
2
1
Pigtail harness
assembly with
8-pin connector
Line voltage
fuse (1 AMP)
Electric hinge with
8-pin connectors
Blue (DS), 6
Connector
to power on LED
White, RR
Wiring Notes:
1. Rail, raceway, electric hinge and pigtail 8-pin
connector terminations and wire colors all match.
2. Tape or cap off ends of unused pigtail wires (not
shown) to ensure that they do not short.
3. A fire alarm tie-in is required on fire rated openings.
4. The fire alarm contact (when required) must be
wired to drop 24VDC power to rail. In this case,
terminate fire alarm contact between the red (+
24VDC) wire and supply + 24VDC output.
ATTENTION:
Electrified Trim applications require a separate
raceway and power transfer device. Installation
of conductors or harnesses (by others) through
the exit device rail is prohibited as it could
lead to product performance issues up to and
including product failure.

16
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
9Sample Wiring Instructions
b57- Exit Device with inside Keypad, Fire Alarm, Door Status and Remote Horn
Wiring Notes:
1. Rail, raceway, electric hinge and pigtail 8-pin
connector terminations and wire colors all match.
2. Tape or cap off ends of unused pigtail wires (not
shown) to ensure that they do not short.
3. A fire alarm tie-in is required on fire rated openings.
4. The fire alarm contact (when required) must be
wired to drop 24VDC power to rail. In this case,
terminate fire alarm contact between the red (+
24VDC) wire and supply + 24VDC output.
A valid code entry at the 4291 (Inside) keypad shunts the 57- exit device and allows egress for a time period
programmable at the keypad. During a fire alarm condition, the contact opens which de-energizes the external
electromagnet and allows immediate egress. When the rail is armed and the door is forced open, the 3287 door
status switch signals the rail sounding the rail alarm.
3520 24VDC 1.0AMP Regulated and Filtered Power Supply
5, Orange (EI)
Red (+24), 2
6, Blue (DS)
Normally Closed Fire
Alarm Contact
(If Required) 7, Brown (Mag -)
Black (-24), 1
Green (EG), 4 2
4
8
7
6
3 15
Pigtail harness
assembly with
8-pin connector
Red (+)
Black (-)
1584
Electromagnetic
Green(NC)
Lock White (C)
3287
Door Status
Switch
(-)
Plug pigtail harness
connector into C
8-pin hinge connector
at frame side NO
1 2 3
4291
Keypad
of door 4 5 6
7 8 9
(Inside)
57- 80 Series Rail
with 8-pin connector 0 # (+)
*
Electric Hinge with
8-pin hinge connector
Raceway harness with
8 & 4-pin connectors.
The 4-pin connectors are not
used here.
Line voltage
fuse (1 AMP)
Connector to
power on LED
HOT
110-120 VAC
NEUT
GND
AC F
Low voltage AC
From transformer
AC
DC
DC
Output
NOTE: This drawing shows the
BPS Series. The PM Series
has no line voltage input, fuse
or connector to power on LED
2.5 AMP polyswitch breaker
Red
Black
Unconnected
terminal for
switch hookup
Battery pack
Voltage adjust for
battery backup
8, Yellow (Mag +)
White (RR), 3
Note: Typical raceway location
is shown. Other locations may
exist depending on door type
ATTENTION:
Electrified Trim applications require a separate raceway and power transfer device. Installation of
conductors or harnesses (by others) through the exit device rail is prohibited as it could lead to
product performance issues up to and including product failure.

17
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
9Sample Wiring Instructions
c57- Exit Device with Fire Alarm, Keypads and Fail Safe ET
During a fire alarm condition, the contact opens which de-energizes the rail electromagnet and allows immediate
egress. A valid code entry at the 4291 (Inside) keypad shunts the 57- exit device and allows egress for a time period
programmable at this keypad. A valid code entry at the 4292 (Outside) keypad unlocks the 773 or 775 Fail Safe ET
and shunts the 57- exit device and allows ingress for a time period programmable at this keypad.
Wiring Notes:
1. Rail, raceway, electric hinge and pigtail
8-pin connector terminations and wire
colors all match.
2. Tape or cap off ends of unused pigtail
wires (not shown) to ensure that they
do not short.
3. A fire alarm tie-in is required on fire
rated openings.
4. The fire alarm contact (when required)
must be wired to drop 24VDC power
to rail. In this case, terminate fire alarm
contact between the red (+ 24VDC)
wire and supply + 24VDC output.
Red (+)
Black (-)
Electromagnetic
Lock
7, Brown (Mag -)
8, Yellow (Mag +)
3520 24VDC 1.0AMP Regulated and Filtered Power Supply
110-120 VAC
Connector
to power
on LED
HOT
NEUT
GND
1 2 3
AC F
Low voltage AC
From transformer
AC
DC DC
Output
NOTE: This drawing shows the
BPS Series. The PM Series has no
line voltage input, fuse or connector
to power on LED.
2.5 AMP polyswitch breaker
Red
Black
Unconnected
Terminal for Switch
Hookup
Battery Pack
Line voltage
fuse (1 AMP)
Voltage adjust for
Battery backup
Note: Typical raceway location
is shown. Other locations may
exist depending on door type
Red (+24), 2
Normally Close
Fire Alarm Contact
(If Required)
5, Orange (EI)
Pigtail harness #1
assembly with
8-pin connector
Blue (DS), 6
Black (- Return), 1
Green (EG), 4
Pigtail harness #2
assembly with
8-pin connector
2, Red (+24)
1, Black (- Return)
Electric Hinge #1
with 8-pin connectors
Electric Hinge #2
with 8-pin connectors
Door harness #1
with 8-pin connector
Door harness #2
with 8-pin connector
57-80 Series Rail
with 8-pin connector
Note: Fail Secure ETs
require different wiring.
Consult factory.
773 or 775 Fail Safe ET
with 8-pin connector
Plug into door harness connector
ATTENTION:
Electrified Trim applications require a separate raceway and power transfer device. Installation of
conductors or harnesses (by others) through the exit device rail is prohibited as it could lead to
product performance issues up to and including product failure.

18
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
10 Operating Instructions
aPower Up Sequence
1. Both insert LEDs illuminate “red” for 2 seconds while concurrently sounding buzzer for 500ms.
2. Both insert LEDs illuminate “green” for 2 seconds (no buzzer).
3. The (4) diagnostic LEDS on bottom of module illuminate for 2 seconds.
4. Insert LED illuminates to the switch position (armed or not armed).
bModes of Operation
There are three modes of operation: Armed (Delayed Egress),
Momentary Egress and Maintained Egress.
These modes are set by fully inserting a valid key and rotating it in
either a clockwise or counter-clockwise direction until there is a
click (detent). Note that a second click must be engaged in order to
set momentary egress. To remove the key, it must be returned to its
original center position.
Center (key out)
Maintained (Disarmed)
Delayed Egress (Armed)
1st click
Momentary Egress
2nd click
Armed Mode
1. Apply power to the System; horn will sound for one second.
2. Both LEDs will flash RED, then both LEDs will flash GREEN.
3. Green (default) or Red LED on Electroguard™ insert will
illuminate (See DIP switch settings section 6).
4. Rail assembly is armed. Latchbolt cannot be retracted by
depressing the push rail for immediate egress. If rail is depressed
for (min.) one second, alarm will sound.
5. If any of above sequence fails to function, the unit is not armed.
See: Troubleshooting section
Green LED
Red LED
*Depends on handing
Momentary Egress Mode
1. Rotate key counter-clockwise to 2nd click and return key to
center position (key out).
2. Red (Default) or Green LED flashes on insert for a factory preset
time of 5 seconds. (For other time selections and LED color, see
Dip Switch Settings section 6). The rail assembly will disarm
itself and de-energize the external magnet for this time period
allowing for momentary egress.
3. After the factory preset time of 5 seconds, delay expires. Rail
assembly re-arms itself and the external magnet is re-energized.
4. Unit is then in Delayed Egress Mode (or Power Up State).

19
1-800-727-5477 • www.sargentlock.com
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
A7743F 1/23
10 Operating Instructions (Continued)
bModes of Operation (Continued)
Maintained Egress Mode
1. Rotate key fully clockwise (one click) and return key to center
position (remove key).
2. Red (default) or Green LED will illuminate. See Dip Switch
Settings section 6 for LED color settings.
3. Rail assembly is disarmed allowing the device to operate as a
standard exit device permitting free egress.
Maintained Egress Mode
Resetting the Unit from Maintained Egress Mode to Armed Mode
1. Rotate key counter-clockwise and return key to center position
(remove key).
2. Maintained Red (Default) or Green LED de-energizes and Armed
Green (default) or Red LED will illuminate. See Dip Switch
Settings section 6.
3. The rail assembly re-arms itself into the Delayed Egress Mode.
External electromagnetic lock is energized. Door is locked.
While in Delayed Egress Mode
1. The rail assembly is armed - Green (default) or Red LED is illuminated,
preventing immediate egress. See Dip Switch Settings section 6.
2. When the push rail is depressed for more than 1 second (nuisance delay),
the alarm will sound and the Red and Green LEDs alternately flash. If
there is no nuisance delay, alarm will sound immediately when push rail is
depressed and the Red and Green LEDs will again flash alternately.
3. The alarm will continue to sound until the rail assembly is reset by
inserting the key into the cylinder located on the mounting insert and
rotating the key clockwise (one click) to return the unit to the armed
mode.
Note: A 57-BC-80 Series device automatically resets 30 seconds after door has been
closed. (Requires door position switch).
4. During first 15 seconds after alarm begins, the rail assembly remains
armed and external electromagnet is locked, preventing immediate
egress. After 15 seconds, the rail releases the external electromagnet,
allowing egress.
Note: The delayed egress time can be factory-set to 30 seconds. Local authority
having jurisdiction (LHJ) prevails. Delay times may be regulated by local codes ordinances and regulations.

20
1-800-727-5477 • www.sargentlock.com A7743F 1/23
Delayed Egress 57-80 Series
Installation Instructions
Exit Device
Copyright © 2005, 2007, 2023, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or
in part without the express written permission of SARGENT Manufacturing Company is prohibited. Patent pending
and/or patent www.assaabloydss.com/patents.
10 Operating Instructions
bModes of Operation (Continued)
Unit Tied Into A Fire Alarm System – Optional for Non-Labeled
Devices
1. In case of a fire/emergency, the rail assembly will release the
external electromagnet instantaneously, voiding the 15 second
delay, allowing immediate egress and continuous immediate
egress.
2. LED will be extinguished and the rail will remain unlocked.
3. Once the fire alarm contact re-closes, the rail assembly
automatically sets the unit into the armed mode, preventing
immediate egress.
Note: Fire Alarm contact must be a normally closed (N.C.) contact.
External Inhibit Input - Optional
Used to provide remote override of the delayed egress unit when in an armed condition.
1. External inhibit is a normally open (N.O.) contact to common (-return).
2. If triggered, the unit is in an unarmed state for the duration of the time delay in the card reader, key switch or
other external inhibit. Once the time delay from external inhibit device expires, the unit arms itself immediately.
Remote Reset Input - Optional
Used to provide remote reset when the delayed egress unit is in alarm and momentary egress when delayed egress
unit is armed.
1. Remote reset input is a normally open (N.O.) contact to common (-return).
2. If triggered when unit is in alarm, the device is immediately reset to armed mode.
3. If triggered when unit is in armed mode, the device shall allow momentary egress for the time specified by the
DIP switch settings then return to armed mode.
Manual hex key dogging (non-fire rated) application note:
If push bar is in the dogged (retracted) position when 24VDC power to rail is cycled (via fire alarm/reset or tempo-
rary power outage), the device will enter hall error mode “Both Insert LEDs flash rapid RED and GREEN”.
To clear this error mode, use the manual hex key to un-dog the push bar, ensure the push bar returns to the extend-
ed (home) position then turn the cylinder key CW to Maintained Egress mode then CCW to the center (Armed)
position (or cycle 24VDC power to rail with cylinder key set to center - Armed position).
The device should clear error mode and Arm.