AVer TR530 User manual

TR530/TR320
Control Codes

CONTENTS
Product Overview........................................................................2
CONNECTIONS...............................................................................3
Device Connections....................................................................3
RS232 Pin Definition...................................................................4
OSD Tree Map............................................................................5
Camera OSD...........................................................................5
Camera Advanced Setting.......................................................6
VISCA Over IP Setting.............................................................7
VISCA Command Codes .........................................................7
PELCO P Command Codes ....................................................9
PELCO D Command Codes..................................................10

2
Product Overview
1
2 3 4 5 6 7 8 9 10
1. PTZ camera
6. 3G-SDI 1 port(PTZ view)
2. Panoramic camera
7. HDMI port(PTZ view)
3. Power indicator
8. Audio in port*
4. RJ-45 port
9. RS-232 port
5. 3G-SDI 2 port(Panoramic view)
10. Power jack
*Audio input level: 1Vrms(max.)

CONNECTIONS
Device Connections
Audio Mixer
RJ-45 cable
Porjector TV
Recording System
HDMI cable
or
Multi Media Management System
Power
Outlet
Power
Adaptor
Power
cord
Control System
RS-232 to
D-Sub 9 cable
Audio
cable
coaxial
cable

RS232 Pin Definition
DIN6
PIN No.
I/O Type
Description
1
Output
DTR
2
Input
DSR
3
--
Not Connect
4
Output
TXD
5
GND
GND
6
Input
RXD

OSD Tree Map
Camera OSD
Tracking
On
Camera
Video Format
Preset
Advanced Setting
Language
Profile
Factory Default
Information
>
>
>
>
>
>
>
>

Camera Advanced Setting
To adjust RS232 protocol, address and baud rate, select Advance Setting from OSD menu. If you
need VISCA-over-IP, please make sure it is turned “On” in the menu.
Tracking
On
Camera
Video Format
Advanced Setting
Preset
Language
Profile
Factory Default
Information
>
>
>
>
>
>
>
>
RS232 Protocol
Address(ADDRD)
Baud Rate
VISCA-over-IP
VISCA
1
9600
off

VISCA Over IP Setting
VISCA Command Codes
Command
Packet
Comments
IF_Clear
8x 01 00 01 FF
x = Cam address
IF_Clear(broadcast)
88 01 00 01 FF
CAM_VersionInq
8x 09 00 02 FF
CAM_Power_ON
8x 01 04 00 02 FF
CAM_Power_OFF
8x 01 04 00 03 FF
PT_Stop
8x 01 06 01 00 00 03 03 FF
PT_Up
8x 01 06 01 0P 0T 03 01 FF
P = Pan speed(0~0x0F)
PT_Down
8x 01 06 01 0P 0T 03 02 FF
T = Tilt speed(0~0x0F)

PT_Left
8x 01 06 01 0P 0T 01 03 FF
PT_Right
8x 01 06 01 0P 0T 02 03 FF
PT_UpLeft
8x 01 06 01 0P 0T 01 01 FF
PT_UpRight
8x 01 06 01 0P 0T 02 01 FF
PT_DownLeft
8x 01 06 01 0P 0T 01 02 FF
PT_DownRight
8x 01 06 01 0P 0T 02 02 FF
PT_Direct
8x 01 06 02 00 00 0Y 0Y 0Y 0Y 0V 0V 0V 0V FF
0xYYYY = pan pos
0xVVVV = tilt pos
PT_Pos_Inq
8x 09 06 12 FF
Zoom_Stop
8x 01 04 07 00 FF
Zoom_Tele
8x 01 04 07 2y FF
y = not support(zoom speed)
Zoom_Wide
8x 01 04 07 3y FF
Zoom_Direct
8x 01 04 47 0Y 0Y 0Y 0Y FF
0xYYYY = zoom pos
Zoom_Pos_Inq
8x 09 04 47 FF
CAM_reset
8x 01 04 3F 00 YY FF
YY = preset num(0~0x7F)
CAM_set
8x 01 04 3F 01 YY FF
CAM_recall
8x 01 04 3F 02 YY FF
CAM_Track_ON
8x 01 04 7D 02 00 FF
CAM_Track_OFF
8x 01 04 7D 03 00 FF
CAM_Profile_Read
8x 01 04 40 01 YY FF
YY = profile num(0x00~0x05)
CAM_Profile_Save
8x 01 04 40 02 YY FF
CAM_WOL_ON
8x 01 04 7E 02 00 FF
CAM_WOL_OFF
8x 01 04 7E 03 00 FF
CAM_PIP_SET
8x 01 04 7F 01 YY FF
YY = pip num(0x00~0x09)
CAM_PIP_OFF
8x 01 04 7F 02 00 FF

PELCO P Command Codes

PELCO D Command Codes