AVer PTZ310 User manual

PTZ310/330
Professional PTZ Camera
Control Codes
V.2.0.4

Contents
Product Introduction ........................................................................... 1
Overview.......................................................................................... 1
RS232 and RS422 Connection.......................................................... 1
OSD Tree .......................................................................................... 4
Camera.....................................................................................4
Advanced Setting...............................................................4
RS232 Command Table .................................................................... 4
Visca over IP Settings......................................................................... 10
....................................................................................................... 10

1
Product Introduction
Overview
(4) (5) (6) (7)(8)(9)(10) (11)(12) (2) (3)
(1)
(1) Camera lens
(5) PoE+ port
(9) micro-USB port
(2) IR sensor
(6) RS232 port
(10) HDMI port
(3) LED indicator
(7) RS422 port
(11) 3G-SDI port
(4) Kensington lock
(8) Audio in*
(12) DC Power jack
*Line input level: 1Vrms (max.).
*Mic input level: 50mVrms (max.); Supplied voltage:2.5V
RS232 and RS422 Connection
Connect through the RS232 or RS422 for camera control. For Visca over IP, please see the last
section.
◼RS232

2
Laptop
Joystick
RS232(VISCA) cable
(Not inculded)
●RS232 Port Pin definition ●Din8 to D-Sub9 Cable Pin definition
6 7 8
3 4 5
1 2
15
69
RS232 Pin
No.
Pin
1
DTR
2
DSR
3
TXD
4
GND
5
RXD
6
GND
7
NC
8
NC

3
1 8
◼RS422
[Note] Use cat5e splitter for multi-camera connection.
Cat5e splitter pin assignment:
1
234
5
678
1
234
5
678 1
234
5
678
PTZ310/330
PTZ310W/330W
Camera/Joystick Camera/Joystick
RS422 Pin
No.
Pin
No.
Pin
1
TX-
5
TX+
2
TX+
6
RX+
3
RX-
7
RX-
4
TX-
8
RX+

4
OSD Tree
Camera
Go to Advanced Setting -> Control. Make sure the Camera Address, Baud Rate setting is correct.
Advanced Setting
Advanced Setting
Audio
Input Type
Mic in/Line in
Auto Gain Control
Off/On
Noise Suppression
Off/On
Audio Volume
0 ~ 10
Control
Protocol
VISCA/Pelco D/Pelco-P/AW
Camera Address
1~7
Baud Rate
2400/4800/9600/38400
Smart Framing
Off/On
Smart Shoot
Off/On
Number of block
2/3/4
Initial Position
Preset 6/Preset 7/Preset 8/Preset 9
Time to back initial position
5s/10s/15s/20s/25s/30s/35s/40s
RS232 Command Table
Command Set
Command
Command Packet
Comments
IF_Clear
Broadcast
88 01 00 01 FF
I/F Clear
CAM_Zoom
Stop
8x 01 04 07 00 FF
Zoom Control
CAM_Zoom
Tele (Standard)
8x 01 04 07 02 FF
CAM_Zoom
Wide (Standard)
8x 01 04 07 03 FF

5
CAM_Zoom
Tele (Variable)
8x 01 04 07 2p FF
p=0 (Low) to 7 (High)
CAM_Zoom
Wide (Variable)
8x 01 04 07 3p FF
CAM_Zoom
Direct
8x 01 04 47 0p 0q 0r 0s FF
pqrs: Zoom Position，
PTZ310: 0x0000~0x6f20
PTZ330: 0x0110~0x5490
CAM_DZoom
On
8x 01 04 06 02 FF
Digital zoom ON/OFF
CAM_DZoom
Off
8x 01 04 06 03 FF
CAM_Focus
Stop
8x 01 04 08 00 FF
Focus Control
CAM_Focus
Far (Standard)
8x 01 04 08 02 FF
CAM_Focus
Near (Standard)
8x 01 04 08 03 FF
CAM_Focus
Direct
8x 01 04 48 0p 0q 0r 0s FF
pqrs: Focus Position，0x0000(wide) ~
0x4000(tele)，
CAM_Focus
Auto Focus
8x 01 04 38 02 FF
AF ON/OFF
CAM_Focus
Manual Focus
8x 01 04 38 03 FF
CAM_Focus
Auto/Manual
8x 01 04 38 10 FF
CAM_Focus
One Push
Trigger
8x 01 04 18 01 FF
One Push AF Trigger
AF_Sensitivity
Normal
8x 01 04 58 02 FF
AF Sensitivity Normal/Low
AF_Sensitivity
Low
8x 01 04 58 03 FF
CAM_AFMode
Normal AF
8x 01 04 57 00 FF
Continous AF
CAM_AFMode
Zoom Trigger
AF
8x 01 04 57 02 FF
Continous AF OFF, only trigger AF
after zoom in/out
CAM_ZoomFocus
Direct
8x 01 04 47 0p 0q 0r 0s 0t 0u
0v 0w FF
pqrs: Zoom Position
tuvw: Focus Position
CAM_WB
Auto
8x 01 04 35 00 FF
Normal Auto
CAM_WB
Indoor
8x 01 04 35 01 FF
Indoor mode

6
CAM_WB
Outdoor
8x 01 04 35 02 FF
Out door mode
CAM_WB
One Push WB
8x 01 04 35 03 FF
One Push WB mode
CAM_WB
Manual
8x 01 04 35 05 FF
Manual Control Mode
CAM_WB
One Push
Trigger
8x 01 04 10 05 FF
One Push WB Trigger
CAM_AE
Full Auto
8x 01 04 39 00 FF
Automatic Exposure mode
CAM_AE
Manual
8x 01 04 39 03 FF
Manual Control mode
CAM_AE
Shutter Priority
8x 01 04 39 0A FF
Shutter priority Exposure mode
CAM_AE
Iris Priority
8x 01 04 39 0B FF
Iris priority Exposure mode
CAM_SlowShutter
Auto
8x 01 04 5A 02 FF
Auto Slow Shutter ON/OFF
CAM_Shutter
Reset
8x 01 04 0A 00 FF
Shutter Setting
CAM_Shutter
Up
8x 01 04 0A 02 FF
CAM_Shutter
Down
8x 01 04 0A 03 FF
CAM_Shutter
Direct
8x 01 04 4A 00 00 0p 0q FF
pq: Shutter Position
CAM_Iris
Reset
8x 01 04 0B 00 FF
Iris Setting
CAM_Iris
Up
8x 01 04 0B 02 FF
CAM_Iris
Down
8x 01 04 0B 03 FF
CAM_Iris
Direct
8x 01 04 4B 00 00 0p 0q FF
pq: Iris Position，
CAM_Gain
Reset
8x 01 04 0C 00 FF
Gain Setting
CAM_Gain
Up
8x 01 04 0C 02 FF
CAM_Gain
Down
8x 01 04 0C 03 FF
CAM_Gain
Direct
8x 01 04 4C 00 00 0p 0q FF
pq: Gain Position，
CAM_Gain
AE Gain Limit
(Direct)
8x 01 04 2C 0p FF
p: Gain Position (4 to F)，
CAM_ExpComp
Reset
8x 01 04 0E 00 FF
Exposure Compensation Amount
Setting
CAM_ExpComp
Up
8x 01 04 0E 02 FF
CAM_ExpComp
Down
8x 01 04 0E 03 FF

7
CAM_ExpComp
Direct
8x 01 04 4E 00 00 0p 0q FF
pq: ExpComp (pq: 0x01~0x09 , Value:
-4~ +4 , Each value = 0.3EV)
CAM_BackLight
On
8x 01 04 33 02 FF
Back Light Comp ON/OFF
CAM_BackLight
Off
8x 01 04 33 03 FF
CAM_LR_Reverse
On
8x 01 04 61 02 FF
Mirror Image ON/OFF
CAM_LR_Reverse
Off
8x 01 04 61 03 FF
CAM_Memory
Reset
8x 01 04 3F 00 pp FF
pp: 0x00 To 0xFF
CAM_Memory
Set
8x 01 04 3F 01 pp FF
pp: 0x00 To 0xFF
pp: 0x5A => SmartFrame Enable
pp: 0x5B => SmartFrame Disable
pp: 0x5C => SmartFrame Trigger
pp: 0x5D => SmartShoot Enable
pp: 0x5E => SmartShoot Disable
pp: 0x5F => Trun on OSD menu
CAM_Memory
Recall
8x 01 04 3F 02 pp FF
SYS_Menu
On
8x 01 06 06 02 FF
turn on the menu screen
SYS_Menu
Off
8x 01 06 06 03 FF
Erasing menu display(turn off the menu
screen/VC-A70H)
SYS_Menu
On/Off
8x 01 06 06 10 FF
turn on/off the menu screen
SYS_Menu
Menu Enter
8x 01 7E 01 02 00 01 FF
menu enter
Pan-tiltDrive
Up
8x 01 06 01 VV WW 03 01
FF
VV: Pan speed setting 0x01 (low
speed) to 0x18 (high speed)
WW: Tilt speed setting 0x01 (low
speed) to 0x18 (high speed)
YYYY: Pan Position 8A14 to 762C
(CENTER 0000)
ZZZZ: Tilt Position 468B to E898
Pan-tiltDrive
Down
8x 01 06 01 VV WW 03 02
FF
Pan-tiltDrive
Left
8x 01 06 01 VV WW 01 03
FF
Pan-tiltDrive
Right
8x 01 06 01 VV WW 02 03
FF

8
Pan-tiltDrive
UpLeft
8x 01 06 01 VV WW 01 01
FF
(Image Flip: OFF) (CENTER 0000)
Pan-tiltDrive
UpRight
8x 01 06 01 VV WW 02 01
FF
Pan-tiltDrive
DownLeft
8x 01 06 01 VV WW 01 02
FF
Pan-tiltDrive
DownRight
8x 01 06 01 VV WW 02 02
FF
Pan-tiltDrive
Stop
8x 01 06 01 VV WW 03 03
FF
Absolute Position
8x 01 06 02 VV WW 0Y 0Y
0Y 0Y 0Z 0Z 0Z 0Z FF
Pan-tiltDrive
Home
8x 01 06 04 FF
Pan-tiltDrive
Reset
8x 01 06 05 FF
Pan-tiltSet
SlowPanTilt
On
8x 01 06 44 02 FF
Pan/Tilt Slow Mode On/Off
Pan-tiltSet
SlowPanTilt
Off
8x 01 06 44 03 FF
Firmware
Firmware
version
8x 01 02 03 FF
Factory Reset
System Factroy
Reset
8x 01 04 3F 03 00 FF
Preset Speed
Set Preset
Speed
8x 01 06 20 0p FF
p: 0 to 2, 0:150/s, 1:250/s, 2: 300/s
(Lumens)
p:0 to 5, (AVer)
CAM_Power_ON
Power On
8x 01 04 00 02 FF
CAM_Power_OFF
Power Off
8x 01 04 00 03 FF