Axiom Ed60p User manual

USER MANUAL

ED60P

passive point source loudspeaker

KEY FEATURES

• Near-eld and mid-eld sound reinforcement applicaons • High quality, low distoron drivers

• Asymmetric HF coverage paern • Audiophile-grade passive crossover network

• Rotatable HF Horn for opmal horizontal coverage • 35° monitor taper

• Water-repellent treatment of LF loudspeaker • Various rigging hardware

INTRODUCTION

ED point source systems are designed for indoor and outdoor sound reinforcement

applicaons ranging from clubs, bars and restaurants to theatres, live music venues, houses

of worship and theme environments. Passive ED series loudspeaker systems are easy to set

up and simple to operate.

The ED60P consists of an 6.5” LF drive unit and a 1” HF compression driver loaded by an

asymmetric HF horn in a compact enclosure, designed for many mul-purpose sound

reinforcement acvies. The asymmetric HF coverage paern, varying from 120° horizontal

in the lower part of the horn for more eecve near eld coverage, and narrowing to 70°

horizontal at the top of the horn for more focused coverage in the far eld. The result is

more accurate coverage of a typical auditorium than is possible with a xed horizontal

coverage device. The HF horn is also rotatable through 90° by simply removing four screws

and realigning the horn, so that coverage can also be opmised for stage monitor use. This

rotatable horn feature also makes it possible to maintain the ideal coverage paern when the

cabinet is installed in a horizontal (landscape) orientaon. Its asymmetric dispersion paern

provides opmal coverage of typical rectangular venues, with wider dispersion at the front

and narrower dispersion at the rear.

This versale loudspeaker can also be used as a low prole stage monitor with its 35°

tapered side, and in this situaon the HF horn can be rotated to maintain the best coverage

paern for performers both near to and further away from the monitor. ED60P cabinet is

an unobtrusive and compact format designed for a multude of near eld applicaons such as theatre under-balcony ll, stage front ll, delay

speaker, bar and restaurant audio, and discreet stage monitor. A pole mount socket make this a very versale loudspeaker in both portable and

permanently installed applicaons.

TECHNICAL SPECIFICATION

Acouscal

LF Power Compression

@ -10 dB Power (20 W) = 0.7 dB

@ -3 dB Power (100 W) = 1.8 dB

@ 0 dB Power (200 W) = 3.5 dB

System type Point Source Loudspeaker

with asymetric HF Horn

Connectors

Low frequency transducer 6.5” (165 mm), 1.5” (38 mm) voice coil, 16Ω Connector Type Neutrik® Speakon® NL4 x 2

Input Wiring Pin 1+/1- (Pin 2+/2- pass thru)

High frequency transducer 1” compression driver, 1” (25 mm) aluminium

voice coil, PEPT diaphragm, 8Ω

Mechanical

Width 210 mm (8.3”)

Height 390 mm (15.3”)

Frequency response 85 Hz – 18 kHz (-6dB) Depth 190 mm (7.5”)

Sensivity (2.83 V @ 1m, 2 Pi) 92 dBSPL Taper angle 35°

Horizontal Coverage Angle 70 to 120° (-6 dB) Construcon 15 mm phenolic birch plywood

Vercal Coverage Angle 60° (-6 dB) Paint Black textured paint (or White)

Maximum Peak SPL @ 1m 114 dB Suspension system

Electrical Suspension Rigging points

Nominal Impedance 16Ω Oponal brackets

Minimum Impedance 13.2 Ω @ 200Hz Net Weight 5 Kg (11 lbs)

Power Handling (AES) 100 W

Power Handling (prgm) 200 W

revision 2017-07-18

h120°

h70°

MECHANICAL DRAWING

OPTIONAL ACCESSORIES

KPTED60B Wall or Truss Mounng “C” bracket.

KPTLTP Wall Mounng bracket.

PLH295 Ø 48-51mm truss tube aluminium half coupler with

M10 x 50 built-in bolt and fastening nut.

NL4FX Neutrik Speakon® PLUG

see hp://www.axiomproaudio.com for detailed descripon and other available accessories.

SPARE PARTS

NL4MP Neutrik Speakon® panel socket 98AXM6W16 6.5’’ woofer - 1.5” VC

91CR0070 ED60P Crossover PCBA 98DRICDX1-1070 1’’ - 1” vc compression driver

21 cm

8.3"

19 cm

7.5"

39 cm

15.3"

Pole Adapter

M8 Flying Point

INSTRUCTION FOR ROTATING THE HORN

1) Remove the speaker grid unscrewing

the four screws indicated below.

2) Unscrew the 4 screws ﬁxing the horn and

rotate the horn by 90°.

turn

90°

Wall

Adapter

REAR PANEL

INPUT - Power input for the external amplier. The ED60P includes a passive crossover for ltering the signal. It includes also an internal protecon

that limits any excessive power to the HF secon and, if the signal persists for a long me, it excludes the HF secon. The connecons are the

following:

INPUT - LINK

NL4 pin number internal connecon

1+ +

1- -

2+ none (pass thru)

2- none (pass thru)

LINK - Power output in parallel with the INPUT socket, for connecng the unit to another

speaker. The number of ED60P cabinets that can be connected in parallel depends on the

amplier load capacity.

HORN ORIENTATION

ED60P features an asymmetrical horn that can be rotated in a few minutes for obtaingn the best coverage according to the speaker conguraon.

KPTED60B WALL or TRUSS MOUNTING

Using the “C” shape bracket the ED60P loudspeaker can be installed to walls or mounted to trusses in combinaon combining with a PLH295.

It allows to aim the speaker in one direcon (vercal or horizontal) in 7 steps (-22.5°,-15°,-7.5°,0°,+7.5°,+15°,+22.5°).

VERTICAL POSITION

FOH CONFIGURATION

HORIZONTAL POSITION

FOH CONFIGURATION

HORIZONTAL POSITION

STAGE MONITOR CONFIGURATION

�ght dispersion

long throw

VERTICAL POSITION

FOH CONFIGURATION

�ght dispersion

long throw

VERTICAL POSITION

FOH CONFIGURATION

wide

dispersion

short throw

wide

dispersion

short throw

�ght

dispersion

long throw

HORIZONTAL POSITION

FOH CONFIGURATION

wide dispersion

short throw

�ght dispersion

long throw

HORIZONTAL POSITION

FOH CONFIGURATION

wide dispersion

short throw

�ght dispersion

long throw

�ght dispersion

long throw

wide dispersion

short throw

�ght

dispersion

long throw

HORIZONTAL POSITION

STAGE MONITOR CONFIGURATION

wide dispersion

short throw

�ght dispersion

long throw

HORIZONTAL POSITION

STAGE MONITOR CONFIGURATION

wide

dispersion

short throw

wide

dispersion

short throw

�ght dispersion

long throw

wide

dispersion

short throw

LIMITED WARRANTY

Proel warrants all materials, workmanship and proper operaon of this product for a period of two years from the original date of purchase. If any defects are found

in the materials or workmanship or if the product fails to funcon properly during the applicable warranty period, the owner should inform about these defects the

dealer or the distributor, providing receipt or invoice of date of purchase and defect detailed descripon. This warranty does not extend to damage resulng from

improper installaon, misuse, neglect or abuse. Proel S.p.A. will verify damage on returned units, and when the unit has been properly used and warranty is sll

valid, then the unit will be replaced or repaired. Proel S.p.A. is not responsible for any “direct damage” or “indirect damage” caused by product defecveness.

• This unit package has been submied to ISTA 1A integrity tests. We suggest you control the unit condions immediately aer unpacking it.

• If any damage is found, immediately advise the dealer. Keep all unit packaging parts to allow inspecon.

• Proel is not responsible for any damage that occurs during shipment.

• Products are sold “delivered ex warehouse” and shipment is at charge and risk of the buyer.

• Possible damages to unit should be immediately noed to forwarder. Each complaint for package tampered with should be done within eight days from product

receipt.

SAFETY INSTRUCTIONS

– To reduce the risk, close supervision is necessary when the product is used near children.

– Protect the apparatus from atmospheric agents and keep it away from water, rain and high humidity places.

– This product should be site away from heat sources such as radiators, lamps and any other device that generate heat.

– This product should be located so that its locaon or posion does not interfere with its proper venlaon and heang dissipaon.

– Care should be taken so that objects and liquids do not go inside the product.

– The product should be connected to a power supply mains line only of the type described on the operang instrucons or as marked on the product. Connect the

apparatus to a power supply using only power cord included making always sure it is in good condions.

– WARNING: The mains plug is used as disconnect device, the disconnect device shall remain readily operable.

– Do not cancel the safety feature assured by means of a polarized line plug (one blade wider than the other) or with a earth connecon.

– Make sure that power supply mains line has a proper earth connecon.

– Power supply cord should be unplugged from the outlet during strong thunderstorm or when le unused for a long period of me.

CE CONFORMITY

Proel products comply with direcve EMC 2014/30/CE, as stated in EN 55103-1 and EN 55103-2 standards and with direcve LVD 2014/35/CE, as stated in EN 60065

standard.

PROEL S.p.A. (World Headquarter) - Via alla Ruenia 37/43 - 64027 Sant’Omero (Te) - ITALY

Tel: +39 0861 81241 Fax: +39 0861 887862 www.axiomproaudio.com

KPTLTP WALL MOUNTING