AXIOMTEK eBOX630-100-FL Series User manual

eBOX630-100-FL Series
Embedded System
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. Axiomtek Co., Ltd. assumes no responsibility for
any infringements of patents or any third party’s rights, and any liability
arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility
for the accuracy, completeness or usefulness of any information in this
document. Axiomtek does not make any commitment to update the
information in this manual.
Axiomtek reserves the right to change or revise this document and/or
product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of Axiomtek Co., Ltd.
Copyright 2012 Axiomtek Co., Ltd.
All Rights Reserved
April 2012, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, please read the following important safety
precautions.
1. User should not modify any unmentioned jumper setting without
Axiomtek FAE’s instruction. Any modification without instruction
might cause system to become damage
2. The eBOX620-110-FL does not come equipped with an operating
system. An operating system must be loaded first before
installing any software into the computer.
3. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
4. Disconnect the power cord from the eBOX620-110-FL before
making any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin
sensitive components. Make sure the eBOX620-110-FL is
properly grounded.
5. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
6. Turn OFF the system power before cleaning. Clean the system
using a cloth only. Do not spray any liquid cleaner directly onto
the screen.
7. Do not leave this equipment in an uncontrolled environment
where the storage temperature is below -20℃or above 80℃. It
may damage the equipment.
8. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to do
so. Integrated circuits on computer boards are sensitive to static
electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity on
your body.
When handling boards/components, wear a wrist-grounding
strap which available from most electronic component stores.

iv
Classification
1. Degree of production against electric shock : not classified
2. Degree of protection against the ingress of water : IP40
3. Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
4. Mode of operation : Continuous

v
General Cleaning Tips
You may need the following precautions before you begin to clean the
computer. When you clean any single part or component for the
computer, please read and understand the details below fully.
When you need to clean the device, please rub it with a piece of dry
cloth.
1. Be cautious of the tiny removable components when you use
a vacuum cleaner to absorb the dirt on the floor.
2. Turn the system off before you start to clean up the
component or computer.
3. Never drop the components inside the computer or get circuit
board damp or wet.
4. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
5. Try not to put any food, drink or cigarette around the
computer.
Cleaning Tools:
Although many companies have created products to help improve the
process of cleaning your computer and peripherals users can also use
household items to clean their computers and peripherals. Below is a
listing of items you may need or want to use while cleaning your
computer or computer peripherals.
Keep in mind that some components in your computer may only be
able to be cleaned using a product designed for cleaning that
component, if this is the case it will be mentioned in the cleaning.
Cloth: A piece of cloth is the best tool to use when rubbing up
a component. Although paper towels or tissues can be used
on most hardware as well, we still recommend you to rub it
with a piece of cloth.
Water or rubbing alcohol: You may moisten a piece of cloth a
bit with some water or rubbing alcohol and rub it on the
computer. Unknown solvents may be harmful to the plastics
parts.

vi
Vacuum cleaner: Absorb the dust, dirt, hair, cigarette particles,
and other particles out of a computer can be one of the best
methods of cleaning a computer. Over time these items can
restrict the airflow in a computer and cause circuitry to
corrode.
Cotton swabs: Cotton swaps moistened with rubbing alcohol
or water are excellent tools for wiping hard to reach areas in
your keyboard, mouse, and other locations.
Foam swabs: Whenever possible it is better to use lint free
swabs such as foam swabs.
Note: We strongly recommended that you should shut down the
system before you start to clean any single components.
Please follow the steps below:
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

vii
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform your
Axiomtek distributor as soon as possible for the suitable solution. For
the computers that are no longer useful or no longer working well,
please contact your Axiomtek distributor for recycling and we will
make the proper arrangement.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows® is a trademark of Microsoft Corporation.
AMI is trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business
Machines Corporation.
Intel® and Pentium® are trademarks of Intel Corporation.
AMD is trademark of AMD Corporation, Inc.
Other brand names and trademarks are the properties and registered
Brands of their respective owners

viii
Table of Contents
Disclaimers....................................................................................ii
Safety Precautions........................................................................iii
Classification.................................................................................iv
General Cleaning Tips...................................................................v
Scrap Computer Recycling..........................................................vii
CHAPTER 1 INTRODUCTION.......................................................... 1
1.1 General Description .................................................... 2
1.2 System Specifications................................................. 3
1.2.1 CPU............................................................................. 3
1.2.2 System I/O .................................................................. 3
1.2.3 System Specification................................................... 3
1.2.4 I/O Port Address Map ................................................. 5
1.2.5 Interrupt Controller...................................................... 7
1.2.6 Driver CD Content....................................................... 8
1.3 Dimensions ................................................................. 9
1.4 I/O Outlets................................................................. 10
1.5 Packing List............................................................... 12
CHAPTER 2 HARDWARE INSTALLATION................................... 13
2.1 Installing the Memory Module................................... 14
2.2 Installing the SATA HDD........................................... 17
2.3 Installing the CFast Card........................................... 22
2.4 Installing the SIM Card.............................................. 25
2.5 Installing the Express Mini Card................................ 29
CHAPTER 3 Jumper Setting & Connector................................... 33
3.1 SBC layout ................................................................ 34
3.2 Jumper Setting Summary ......................................... 36
3.2.1 Audio Output Selection Jumper (JP1)....................... 37
3.2.2 Auto Power On (JP11).............................................. 37
3.2.3 CMOS Clear Jumper (JP11)..................................... 38
3.3 Connectors................................................................ 39
3.3.1 DC-in Jack Power Connector.................................... 39
3.3.2 Serial Port Connector................................................ 40
3.3.3 DisplayPort Connector.............................................. 41
3.3.4 VGA Connector......................................................... 42
3.3.5 LAN Connector (LAN1, LAN2).................................. 43
3.3.6 USB Connector......................................................... 43

ix
3.3.7 ATX Power On/OFF Button ...................................... 44
3.3.8 Audio Connector ....................................................... 44
3.3.9 SATA Connector....................................................... 44
3.3.10 CFast™ Socket......................................................... 45
3.3.11 DDR3 SODIMM Socket............................................ 46
3.3.12 PCI-Express MiniCard.............................................. 46
3.3.13 PCI-Express MiniCard.............................................. 47
CHAPTER 4 AMI BIOS SETUP UTILITY ....................................... 49
4.1 Starting...................................................................... 50
4.2 Navigation Keys ........................................................ 51
4.3 Main Menu ................................................................ 52
4.4 Advanced Menu........................................................ 53
4.5 Chipset Menu............................................................ 60
4.6 Boot Menu................................................................. 69
4.7 Security Menu........................................................... 70
4.8 Save & Exit Menu...................................................... 71
APPENDIX A WATCHDOG TIMER ................................................ 73

x
MEMO

eBOX630-100-FL Series User’s Manual
Introduction
1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the eBOX630-100-FL. The Chapter 1 includes the following
sections:
General Description
System Specification
Dimensions
I/O Outlets
Package List

eBOX630-100-FL Series User’s Manual
Introduction
2
1.1 General Description
The eBOX630-100-FL is an embedded system that supports AMD G-
series APU T56N 1.65GHz dual core onboard processor with AMD
FCH A50M chipset. It can provide Windows®XPE, Windows®XP,
Windows®WinCE embedded and Linux, suitable for the most
endurable operation.It features fanless design with full feature I/O, one
204-pin DDR3 SODIMM maximum up to 4GB, and enhanced system
dependability by built-in Watchdog Timer.
Features
1. Support AMD G-series APU T56N 1.65GHz dual core
onboard processor and A50M shipset
2. High graphic performance and full feature I/O
3. Supports 6 USB 2.0 ports, 4 COM ports
4. Supports dual 10/100/1000Mbps Ethernet port
5. One 2.5”SATA HDD drive bay
6. One front access CFast
7. Watchdog timer
8. 60W adapter
9. Support fordual display with different content
Reliable and Stable Design
The eBOX630-100-FL adopts the advanced cooling system
and supporting the CFast, which makes it especially suitable
for vibration environments, best for industrial automation,
digital signage and gaming application.
Embedded O.S. Supported
The eBOX630-100-FL not only supports Windows® XP, but
also supports embedded OS, such as Windows® XP
embedded, WinCE and Linux. For storage device, the
eBOX630-100-FL supports one 2.5" SATA HDD drive bay,
and one CFast slot.

eBOX630-100-FL Series User’s Manual
Introduction
3
1.2 System Specifications
1.2.1 CPU
CPU
AMD G-Series APU dual core T56N 1.65GHz
Chipset
AMD FCH A50M
BIOS
American Megatrends Inc. UEFI (Unified Extensible
Firmware Interface) BIOS.
16Mbit SPI Flash, DMI, Plug and Play.
RPL/PXE Ethernet Boot ROM.
System Memory
One 204-pin unbuffered DDR3 SO-DIMM socket.
Maximum to 4GB DDR3 1333MHz memory for T56N.
1.2.2 System I/O
Four 9-pin D-Sub male connectors, COM1 for RS232/422/485,
and COM2~COM4 for RS-232
One 15-pin D-Sub female connector for VGA
Dual DisplayPorts
HD audio compliant with Realtek ALC662 (Mic-IN, Line-OUT)
Two ports with Realtek RTL8111E for Gigabit/Fast Ethernet.
Six USB 2.0 connectors
One 12V DC Jack for power input connector with ACPI support
1.2.3 System Specification
Watchdog Timer
Reset supported; 255 levels, 1~255 sec.
Power Supply
External 12V@5A, 60W AC/DC power adapter
Operation Temperature
-10℃~ 60℃(14 ºF ~ 140ºF) with W.T. HDD

eBOX630-100-FL Series User’s Manual
Introduction
4
Storage Temperature
-20℃~ 80℃(-4 ºF ~ 176ºF)
Humidity
10% ~ 90% (non-condensation)
Vibration Endurance
2Grms w/ CF (5 ~ 500Hz, X, Y, Z directions)
Weight
2.5 kg (5.51 lb) without package
4.5 kg (9.92 lb) with package
Dimensions
280mm(11.02”) (W) x 150mm(5.91”) (D) x67mm(2.64”) (H)
NOTE:All specifications and images are subject to change without
notice.

eBOX630-100-FL Series User’s Manual
Introduction
5
1.2.4 I/O Port Address Map
The AMD G-Series APU communicates via I/O ports. Total 1KB port
addresses are available for assigning to other devices via I/O
expansion cards.

eBOX630-100-FL Series User’s Manual
Introduction
6

eBOX630-100-FL Series User’s Manual
Introduction
7
1.2.5 Interrupt Controller
The eBOX630-100-FL is 100% PC compatible control board which
consists of 20 interrupt request lines. Four out of 20 can be
programmable. The mapping list of the 20 interrupt request lines is
shown as the following table.

eBOX630-100-FL Series User’s Manual
Introduction
8
1.2.6 Driver CD Content
Win7
AHCI
Audio
Chip
LAN
WinXP
AHCI
Audio
Chip
LAN
Linux
Chipset
Audio
LAN
Manual
Quick Manual
User Manual

eBOX630-100-FL Series User’s Manual
Introduction
9
1.3 Dimensions
The following diagrams show you dimensions and outlines of
the eBOX630-100-FL.

eBOX630-100-FL Series User’s Manual
Introduction
10
1.4 I/O Outlets
The following figures show you I/O outlets on front view of the
eBOX630-100-FL.
Front View of eBOX630-100-FL
Front View drawing
2 x USB 2.0
connectors
SMA Antenna
openings
Audeio
Connectors
Power & HDD
Indicators