AXIOMTEK EBOX630-830 User manual

i
EBOX630-830
Fanless Embedded System
User’s Manual

ii
Disclaimers
The information in this manual has been carefully checked and is believed to
be accurate. AXIOMTEK Co., Ltd. assumes no responsibility for any
infringements of patents or other rights of third parties, which may result from
its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may be
contained in this document. AXIOMTEK makes no commitment to update or
to keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this document and/or
product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted, in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of
AXIOMTEK Co., Ltd.
©Copyright 2008 by AXIOMTEK Co., Ltd.
All rights reserved.
January 2008, Version A1
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. The EBOX630-830 does not come equipped with an operating
system. An operating system must be loaded first before
installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
3. Disconnect the power cord from the EBOX630-830 before
making any installation. Be sure both the system and the
external devices are turned OFF. Sudden surge of power
could ruin sensitive components. Make sure the
EBOX630-830 is properly grounded.
4. Make sure the voltage of the power source is correct before
connecting the equipment to the power outlet.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen.
6. Do not leave this equipment in an uncontrolled environment
where the storage temperature is below -20℃ or above 60℃.
It may damage the equipment.
7. Do not open the system’s back cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to
do so. Integrated circuits on computer boards are sensitive to
static electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
zBefore handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static electricity
on your body.
zWhen handling boards and components, wear a
wrist-grounding strap, available from most electronic
component stores.

iv
Classification
1. Degree of production against electric shock: not classified
2. Degree of protection against the ingress of water: IPX0
3. Equipment not suitable for use in the presence of a flammable
anesthetic mixture with air or with oxygen or nitrous oxide.
4. Mode of operation: Continuous
5. Type of protection against electric shock: Class I equipment

v
General Cleaning Tips
You may need the following precautions before you begin to clean
the computer. When you clean any single part or component for
the computer, please read and understand the details below fully.
1. When you need to clean the device, please rub it with a piece
of dry cloth.
2. Be cautious of the tiny removable components when you use
a vacuum cleaner to absorb the dirt on the floor.
3. Turn the system off before you start to clean up the
component or computer.
4. Never drop the components inside the computer or get circuit
board damp or wet.
5. Be cautious of all kinds of cleaning solvents or chemicals
when you use it for the sake of cleaning. Some individuals
may be allergic to the ingredients.
6. Try not to put any food, drink or cigarette around the
computer.
Cleaning Tools:
Although many companies have created products to help
improve the process of cleaning your computer and
peripherals users can also use household items to clean their
computers and peripherals. Below is a listing of items you may
need or want to use while cleaning your computer or computer
peripherals.
Keep in mind that some components in your computer may
only be able to be cleaned using a product designed for
cleaning that component, if this is the case it will be mentioned
in the cleaning.
zCloth: A piece of cloth is the best tool to use when rubbing
up a component. Although paper towels or tissues can be
used on most hardware as well, we still recommend you to
rub it with a piece of cloth.
zWater or rubbing alcohol: You may moisten a piece of cloth a
bit with some water or rubbing alcohol and rub it on the
computer. Unknown solvents may be harmful to the plastics
parts.
zVacuum cleaner: Absorb the dust, dirt, hair, cigarette

vi
particles, and other particles out of a computer can be one of
the best methods of cleaning a computer. Over time these
items can restrict the airflow in a computer and cause
circuitry to corrode.
zCotton swabs: Cotton swaps moistened with rubbing alcohol
or water are excellent tools for wiping hard to reach areas in
your keyboard, mouse, and other locations.
zFoam swabs: Whenever possible it is better to use lint free
swabs such as foam swabs.
Note:
We strongly recommended that you should shut down the
system before you start to clean any single components.
Please follow the steps below.
1. Close all application programs
2. Close operating software
3. Turn off power switch
4. Remove all device
5. Pull out power cable

vii
Scrap Computer Recycling
If the computer equipments need the maintenance or are beyond
repair, we strongly recommended that you should inform us as
soon as possible for the suitable solution. For the computers that
are no longer useful or no longer work well, please contact us for
recycling and we will make the proper arrangement.

viii
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
MS-DOS, Microsoft C and QuickBASIC are trademarks of
Microsoft Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties of their
respective owners.

ix
This page does not contain any information.

Table of Contents
x
Table of Contents
Disclaimers...........................................................................ii
Safety Precautions .............................................................iii
Classification......................................................................iv
General Cleaning Tips....................................................... v
Scrap Computer Recycling..............................................vii
C h a p t e r 1 .....................................................................1
Introduction..........................................................................1
1.1 General Description.................................................1
1.2 Specifications ...........................................................2
1.2.1 Main CPU Board........................................................2
1.2.2 I/O System.................................................................2
1.2.3 System Specification................................................3
1.3 Dimensions ...............................................................4
1.4 I/O Outlets .................................................................5
1.5 Package List..............................................................6
C h a p t e r 2 .....................................................................7
Hardware Installation.........................................................7
2.1 HDD Installation........................................................7
2.2 Install Memory Module.............................................12
C h a p t e r 3......................................................................16
BIOS Setting.......................................................................16
3.1 Entering Setup........................................................16
3.2 Control Keys ...........................................................17
3.3 Getting Help ............................................................17
3.4 The Main Menu........................................................18
3.5 Standard CMOS Setup Menu ................................19
3.6 Advanced BIOS Features ......................................24
3.7 Advanced Chipset Features..................................29