AXIOMTEK GOT-3106TL-830 User manual

GOT-3106TL-830
All-in-One
10.4” SVGA TFT Fanless Compact-Size
PANEL PC
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain
accurate information. AXIOMTEK Co., Ltd. assumes no responsibility
for any infringements of patents or any third party’s rights, and any
liability arising from such use.
AXIOMTEK does not warrant or assume any legal liability or
responsibility for the accuracy, completeness or usefulness of any
information in this document. AXIOMTEK does not make any
commitment to update the information in this manual.
AXIOMTEK reserves the right to change or revise this document
and/or product at any time without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
©Copyright 2010 AXIOMTEK Co., Ltd.
All Rights Reserved
February 2011, Version A1
Printed in Taiwan

iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested in compliance with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are meant to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate or
radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to another outlet of a circuit that
doesn’t connect with the receiver.
4. Consult the dealer or an experienced radio/TV technician for
help.
Shielded interface cables must be used in order to comply with the
emission limits.

iv
Safety Precautions
Before getting started, please read the following important safety
precautions.
1. The GOT-3106TL-830 does not come equipped with an
operating system. An operating system must be loaded first
before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist
strap and place all electronic components in any static-
shielded devices. Most electronic components are sensitive
to static electrical charge.
3. Disconnect the power cord from the GOT-3106TL-830
before any installation. Be sure both the system and external
devices are turned OFF. A sudden surge of power could ruin
sensitive components that the GOT-3106TL-830 must be
properly grounded.
4. The brightness of the flat panel display will be getting weaker
as a result of frequent usage. However, the operating period
varies depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the
system using a cloth only. Do not spray any liquid cleaner
directly onto the screen. The GOT-3106TL-830 may come
with or w/o a touchscreen. Although the touchscreen is
chemical resistant, it is recommended that you spray the
liquid cleaner on a cloth first before wiping the screen. In
case your system comes without the touchscreen, you must
follow the same procedure and not spray any cleaner on the
flat panel directly.
6. Avoid using sharp objects to operate the touchscreen.
Scratches on the touchscreen may cause malfunction or
internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration.
When assembling the GOT-3106TL-830, make sure it is
securely installed.
8. Do not open the system’s back cover. If opening the cover
for maintenance is a must, only a trained technician is
allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from
electrostatic discharge, observe the following precautions:

v
zBefore handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few
seconds. This will help to discharge any static
electricity on your body.
zWhen handling boards and components, wear a wrist-
grounding strap, available from most electronic
component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
IBM, PC/AT, PS/2, VGA are trademarks of International
Business Machines Corporation.
Intel®and Atom™are registered trademarks of Intel Corporation.
MS-DOS, Microsoft C and Quick BASIC are trademarks of Microsoft
Corporation.
VIA is a trademark of VIA Technologies, Inc.
SST is a trademark of Silicon Storage Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
Other brand names and trademarks are the properties and registered
brands of their respective owners.
–

vi
Table of Contents
Disclaimers..........................................................................ii
Safety Approvals.................................................................iii
Safety Precautions..............................................................iv
CHAPTER 1 INTRODUCTION......................................... 1
1.1General Description............................................1
1.2Specifications......................................................3
1.2.1Main CPU Board......................................................... 3
1.2.2I/O System .................................................................. 3
1.2.3System Specification .................................................. 4
1.3Dimensions.........................................................5
1.4I/O Outlets...........................................................6
1.5Packing List ........................................................7
CHAPTER 2 HARDWARE INSTALLATION ................ 8
2.1Open back cover.................................................8
2.2CF card Installation...........................................10
2.2Serial Ports Interface........................................11
2.3Ethernet............................................................13
2.4Mountings: Panel / Wall / Desktop / VESA.......14
2.4.1 VESA-ARM/Wall-Mount ............................................... 14
2.4.2 Desktop Kit Assembly ..................................................15
2.4.3 Panel-mount Kit Assembly........................................... 15
2.5HDD Installation................................................16
2.6DRAM Installation.............................................18
2.7Wireless LAN Card Installation.........................20
2.8Power................................................................22
CHAPTER 3 AMI BIOS SETUP UTILITY ..................... 24
3.1Starting .............................................................24
3.2Navigation Keys................................................24
3.3Main Menu........................................................25
3.4Advanced Menu................................................26
3.5PCI PnP Menu..................................................39
3.6Boot Menu ........................................................42
3.7Security Menu...................................................47

vii
3.8Chipset Menu....................................................49
3.9Exit Menu..........................................................54
CHAPTER 4 DRIVERS INSTALLATION ..................... 56
4.1System..............................................................56
4.2Touch Screen ...................................................57
4.2.1Specification.............................................................. 57
4.2.2Driver Installation- Windows XP ............................... 57
4.3Embedded O.S.................................................60
4.3.1Windows XP Embedded...........................................60

viii
MEMO

GOT-3106TL-830 User’s Manual
Introduction 1
CHAPTER 1
INTRODUCTION
This chapter contains general information and detailed specifications
of the GOT-3106TL-830. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT-3106TL-830 adopts a 10.4-inch SVGA TFT LCD with
400 nits brightness and an Intel®AtomTM processor N270 1.6
GHz to provide excellent computing performance and thermal
resistance. This fanless platform is especially designed for
operating under heavy-duty environment including steel
refinery, oil pipe, ship, machine maker operating systems and
many more. Having below abilities makes GOT-3106TL-830
surely a most robust and cost-effective solution.

GOT-3106TL-830 User’s Manual
Introduction
2
Wide Operating Temperature Range
GOT-3106TL-830 features a technology of wide operating
temperature range which allows it to work between -10°C to
+55°C. It incorporates compact ID and fanless cooling system
with a low power Intel®AtomTM processor N270 1.6 GHz,
making the platform a power-efficient solution.
Reliable and Stable Design
The GOT-3106TL-830 adopts a fan-less cooling system and a
CompactFlash™card, which makes it especially suitable for
vibration-heavy environments, best for the transportation, ship,
and industrial machinery markets. For high capacity storage
requirement, GOT-3106TL-830 can work under 1.3G (5 ~
500Hz, random for 2.5” HDD) in operation mode with a patent
of anti-vibration design. The patent improves the system
reliability and sustainability.
WLAN Antenna Supported (optional)
GOT-3106TL-830 has a PCI Express Mini Card slot for optional
add-ons such as wireless LAN card for 802.11 b/g connections
& 3G/GPRS application, graphics-enhanced video card,
universal analog TV/FM tuner/AV capture card, and more. It
also provides an optional fixed rotational WLAN antenna for
wireless network connection.
More Features
GOT-3106TL-830 utilizes one 200-pin DDR2 533 SODIMM system
memory max. up to 2GB, one SATA HDD and one CompactFlashTM
slot. It provides over-current protection-fuse and a full set of I/O
including 3 RS-232, 1 RS-232/422/485, 4 USB 2.0, 1 audio (line-out),
1 Gigabit Ethernet and 1 VGA. Additionally, this slim unit supports
panel mount, wall mount (optional), VESA mount (optional) and
desktop stand (optional).

GOT-3106TL-830 User’s Manual
Introduction 3
1.2 Specifications
1.2.1 Main CPU Board
zCPU
Intel○RAtomTM N270 1.6GHz processor with FSB 533MHz
onboard
zSystem Chipset
945GSE + ICH7M
zBIOS
America Megatrends BIOS
zSystem Memory
One 200-pin DDR2 SO-DIMM socket
Maximum memory up to 2GB
1.2.2 I/O System
zStandard I/O
Three RS-232 and one RS-232/422/485
Four USB 2.0
zEthernet
One RTL81111b Gigabit Ethernet
zAudio
One Line-out
zExpansion
One Mini card
zStorage
One slot for CF card
One SATA
zPower connector
Phoenix power connector

GOT-3106TL-830 User’s Manual
Introduction
4
1.2.3 System Specification
z10.4” SVGA(800x600) LCD with LED backlight
z5 wired resistive Touch
zFanless Heat Dispensing Design
zIP65 aluminum front bezel
zDisk drive housing:
One 2.5” SATA drive
zNet Weight
3.6 Kg (7.93 lb)
zDimension (Main Body Size)
290mm x 248mm x 65.8mm
zOperation Temperature
-10℃to 55℃
zRelative Humidity
10% to 90% @ 40℃, Non-Condensing
zPower input
12/24VDC with phoenix power connector
NOTE All specifications and images are subject to change
without notice.
NOTE If the operation temperature is higher than 40℃, the
wide temperature DRAM is recommended to be used on
the device.

GOT-3106TL-830 User’s Manual
Introduction 5
1.3 Dimensions
The following diagrams show the dimensions and outlines of
GOT-3106TL-830.

GOT-3106TL-830 User’s Manual
Introduction
6
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT-
3106TL-830.
No Function No Function
1 POWER SWITCH (ATX) 7 COM 2 (RS-232)
2 Power Input connector (phoenix type) 8 VGA
3 2 X USB 2.0 9 1X ETHERNET (RJ-45)
4 COM 3 (RS-232) 10 2 X USB 2.0
5 COM 1 (RS-232/422/485) 11 AUDIO (LINE-OUT)
6 COM 4 (RS-232)

GOT-3106TL-830 User’s Manual
Introduction 7
1.5 Packing List
When you receive the GOT-3106TL-830, the bundled package should
contain the following items:
zGOT-3106TL-830 unit x 1
zDriver CD x1
zPhoenix connector x 1
zPanel mount kit x 6
zScrews for HDD x 4
If you can not find the package or any items are missing, please
contact AXIOMTEK distributors immediately.

GOT-3106TL-830 User’s Manual
Hardware Installation
8
CHAPTER 2
HARDWARE INSTALLATION
The GOT-3106TL-830 provides rich I/O ports and flexible expansions
for you to meet different demand, for example, CF card. The chapter
will show you how to install the hardware. It includes:
CompactFlash™Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card
2.1 Open back cover
This section tells users how to open back cover. Please follow the
steps below.
Step 1 Unscrew ten screws on the back cover. Please refer
the photo below.

GOT-3106TL-830 series User’s Manual
Hardware Installation 9
Step 2 Remove the back cover.

GOT-3106TL-830 User’s Manual
Hardware Installation
10
2.2 CF card Installation
The GOT-3106TL-830 provides one CF slot for users to install
CompactFlash™card. Please refer to the following instructions for
installation:
Step 1 Unscrew two screws on the cover of CF card slot on right
side of GOT.
Î
Step 2 Insert the card into the socket.
Î
Step 3 Close the cover of CF card slot and fix it. Installation
completes.

GOT-3106TL-830 series User’s Manual
Hardware Installation 11
2.2 Serial Ports Interface
The GOT-3106TL-830 has four serial ports. COM1 is RS-232/422/485,
while COM2, COM3, and COM4 are RS-232.
The following table shows you the pin assignments of this connector:
Pin Signal Pin Signal
1 Data Carrier Detect (DCD) 6 Data Set Ready (DSR)
2 Receive Data (RXD) 7 Request To Send (RTS)
3 Transmit Data (TXD) 8 Clear To Send (CTS)
4 Data Terminal Ready (DTR) 9 Ring Indicator (RI)
5 Ground (GND)
In addition, COM1 can be set for RS-232/422/485 by jumper. The
jump setting is listed as below:
COM1 JP11 JP12 JP13
RS-232 (default) 3-5, 4-6 3-5, 4-6 1-2
RS-422 1-3, 2-4 1-3, 2-4 3-4, 7-8
RS-485 1-3, 2-4 1-3, 2-4 5-6, 7-8

GOT-3106TL-830 User’s Manual
Hardware Installation
12
When COM1 is set to RS-422 or RS-485, the pin assignments are
listed below:
Pin # Signal Name
RS-422 RS-485
1 TX- DATA-
2 TX+ DATA+
3 RX+ No connector
4 RX- No connector
5 No connector No connector
6 No connector No connector
7 No connector No connector
8 No connector No connector
9 GND GND