AXIOMTEK GOT5152T-832 User manual

GOT5152T-832
All-in-One
15”XGA TFT Fanless
Touch Panel Computer with
Intel®AtomTM D2550 Processor
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make
any commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted,
in any form or by any means, electronic, mechanical, photocopying, recording, or
otherwise, without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by
the manufacturer that you follow the manufacturer’s instructions to only replace the same
or equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
August 2013, Version A4
Printed in Taiwan

iii
Safety Precautions
Before getting started, read the following important cautions.
1. The GOT5152T-832 does not come equipped with an operating system. An operating
system must be loaded first before installing any software into the computer.
2. Be sure to ground yourself to prevent static charge when installing the internal
components. Use a grounding wrist strap and place all electronic components in any
static-shielded devices. Most electronic components are sensitive to static electrical
charge.
3. Disconnect the power cord from the GOT5152T-832 before any installation. Be sure both
the system and external devices are turned OFF. A sudden surge of power could ruin
sensitive components that the GOT5152T-832 must be properly grounded.
4. The brightness of the flat panel display will be getting weaker as a result of frequent
usage. However, the operating period varies depending on the application environment.
5. Turn OFF the system power before cleaning. Clean the system using a cloth only. Do not
spray any liquid cleaner directly onto the screen. The GOT5152T-832 comes with a
touchscreen. Although the touchscreen is chemical resistant, it is recommended that you
spray the liquid cleaner on a cloth first before wiping the screen. In case your system
comes without the touchscreen, you must follow the same procedure and not spray any
cleaner on the flat panel directly.
6. Avoid using sharp objects to operate the touchscreen. Scratches on the touchscreen
may cause malfunction or internal failure to the touchscreen.
7. The flat panel display is not susceptible to shock or vibration. When assembling the
GOT5152T-832, make sure it is securely installed.
8. Do not open the system’s back cover. If opening the cover for maintenance is a must,
only a trained technician is allowed to do so. Integrated circuits on computer boards are
sensitive to static electricity. To avoid damaging chips from electrostatic discharge,
observe the following precautions:
Before handling a board or integrated circuit, touch an unpainted portion of the
system unit chassis for a few seconds. This will help to discharge any static
electricity on your body.
When handling boards and components, wear a wrist-grounding strap, available
from most electronic component stores.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®and Atom®are trademarks of Intel Corporation.
AMI is trademark of American Megatrend Inc.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
CHAPTER 1 INTRODUCTION .............................................................................. 1
CHAPTER 2 HARDWARE AND INSTALLATION...................................................... 8
2.1 OPEN BACK COVER...............................................................................................9
2.2 CF CARD INSTALLATION.........................................................................................9
2.3 JUMPER AND SWITCH SETTINGS ...........................................................................11
2.4 COM PORT CONNECTOR ...................................................................................13
2.5 ETHERNET.......................................................................................................14
2.6 MOUNTINGS:PANEL /WALL /VESA...................................................................14
2.7 HDD INSTALLATION ...........................................................................................17
2.8 DRAM INSTALLATION ........................................................................................19
2.9 WIRELESS LAN CARD INSTALLATION .....................................................................20
2.10 POWER INPUT ..................................................................................................22
CHAPTER 3 AMI BIOS SETUP UTILITY................................................................23
3.1 STARTING.........................................................................................................23
3.2 NAVIGATION KEYS .............................................................................................23
3.3 MAIN MENU....................................................................................................24
3.4 ADVANCED MENU.............................................................................................25
3.5 CHIPSET MENU.................................................................................................32
3.6 BOOT MENU ....................................................................................................34
3.7 SECURITY MENU ...............................................................................................35
3.8 SAVE &EXIT MENU...........................................................................................36
CHAPTER 4 DRIVERS INSTALLATION................................................................39
4.1 SYSTEM ...........................................................................................................39
4.2 TOUCH SCREEN.................................................................................................39
4.3 EMBEDDED O.S................................................................................................41

v
This page is intentionally left blank.

GOT5152T-832 User’s Manual
Introduction 1
Back
Chapter 1
Introduction
This chapter contains general information and detailed specifications of the
GOT5152T-832. Chapter 1 includes the following sections:
General Description
Specification
Dimensions
I/O Outlets
Package List
1.1 General Description
The GOT5152T-832 is a fan-less and compact-size touch panel computer, equipped
with a 15”TFT LCD display and low power consumption Intel® Atom™D2550
1.86GHz processor. The GOT5152T-832 supports Windows® 7 32-bit, and WES 7.
The panel computer provides a Mini card slot for wireless module. Its excellent ID
and friendly user interface make it a professional yet easy-to-use panel computer.
The GOT5152T-832 is an ideal for space-limited applications in factory
automation, machine maker operating systems, building automation, and more.

GOT5152T-832 User’s Manual
2 Introduction
Back
Reliable and Stable Design
The GOT5152T-832 adopts a fanless cooling system, which makes it suitable for
vibration environments.
Embedded O.S. Supported
The GOT5152T-832 not only supports Windows® 7 32-bit, but also supports
embedded OS, such as WES 7. For storage device, the GOT5152T-832 supports
CompactFlash™ card(optional) and 2.5” SATA device.
Industrial-grade Product Design
The GOT5152T-832 has an incredible design to be used in different industrial
environments.
The front bezel meets the IP65/NEMA4 standard.
For connecting other devices, the GOT5152T-832 also features several interfaces: USB,
Ethernet, and RS-232/422/485.
1.2 Specifications
Main CPU Board
CPU
Intel®AtomTM D2550 1.86GHz processor onboard
System Chipset
Intel®NM10 Express
System Memory
One 204-pin DDR3 SO-DIMM socket
Maximum memory up to 4GB
BIOS
America Megatrends BIOS
I/O System
Standard I/O
Two RS-232 and one RS-232/422/485
Four USB 2.0
One VGA
Ethernet
Two Gigabit Ethernet

GOT5152T-832 User’s Manual
Introduction 3
Back
Audio
One Line-out
Expansion
One Mini card
Storage
One slot for CF card
One SATA
Power connector
GOT5152T-832: DC Power input +10~30VDC (phoenix type)
GOT5152T-832-J: AC 100~240V to DC +12V adapter(Screw type)
System Specification
15”XGA(1024x768) LCD with LED backlight
5 wired resistive Touch
Fanless Heat Dispensing Design
Disk drive housing:
One 2.5”SATA drive
Net Weight
3.2 Kg (7.05 lb)
Dimension (Main Body Size)
387.9mm x 307.7mm x 54.6mm
Operation Temperature
0℃to 50℃
Relative Humidity
10% to 90% @ 40℃, Non-Condensing
Vibration
5 to 500 Hz, 2.0 G random for CompactFlash™/ SSD
Power input
10~30VDC with phoenix power connector
External 60W AC Adapter
—Input: 100VAC to 240VAC
—Output: 12VDC, Max. 5A
Note: All specifications and images are subject to change without notice.
Note: If the operation temperature is higher than 35 ℃ , the wide operating
temperature HDD is recommended to be used on the device.
Note: If the operation temperature is higher than 45 ℃ , the wide temperature DRAM
and CF are recommended to be used o the device.

GOT5152T-832 User’s Manual
4 Introduction
Back
1.3 Dimensions and Outlines
The following diagrams show the dimensions and outlines of GOT5152T-832.

GOT5152T-832 User’s Manual
Introduction 5
Back

GOT5152T-832 User’s Manual
6 Introduction
Back
1.4 I/O Outlets
Please refer to the following illustration for I/O locations of the GOT5152T-832.
No
Function
No
Function
1
POWER SWITCH (ATX)
7
COM 1 (RS-232/422/485)
2
Power Input connector (Phoenix)
8
COM 2 (RS-232)
3
Power Input connector (Screw)
9
Ethernet (RJ-45)
4
Dual USB 2.0 ports
10
Dual USB 2.0 ports
5
COM 3(RS-232)
11
AUDIO (LINE-OUT)
6
VGA

GOT5152T-832 User’s Manual
Introduction 7
Back
1.5 Packing List
When you receive the GOT5152T-832, the bundled package should contain the
following items:
GOT5152T-832 unit x 1
Driver CD x 1
Panel mount kit x 10
Wall mount kit x 1
Screws for HDD x 4
HDD Mylar Sticker x 1
Phoenix connector x 1 (for GOT5152T-832)
Power Adapter & Cord x 1 (for GOT5152T-832-J)
If you cannot find the package or any items are missing, please contact Axiomtek
distributors immediately.

GOT5152T-832 User’s Manual
8 Hardware and Installation
Back
Chapter 2
Hardware and Installation
The GOT5152T-832 provides rich I/O ports and flexible expansions for you to meet different
demand, for example CF card. The chapter will show you how to install the hardware. It
includes:
Open Back Cover
CompactFlash™Card
Serial Port
Ethernet
Mounting Method
Hard disk
DRAM
Wireless LAN Card

GOT5152T-832 User’s Manual
Hardware and Installation 9
Back
2.1 Open back cover
This section tells users how to open back cover. Please follow the steps below.
Step 1 Unscrew 12 screws on the back cover. Please refer the photo below.
Step 2 Remove the back cover.

GOT5152T-832 User’s Manual
10 Hardware and Installation
Back
2.2 CF card Installation
The GOT5152T-832 provides one CF slot for users to install CompactFlash™card. Please
refer to the following instructions for installation:
Step 1 Turn off the system, and unplug the power cord.
Step 2 Find out the cover on the side of the system.
Step 3 Locate the CompactFlash™socket, and insert the card into the socket.

GOT5152T-832 User’s Manual
Hardware and Installation 11
Back
2.3 Jumper and Switch Settings
Jumper is a small component consisting of jumper clip and jumper pins. Install
jumper clip on 2 jumper pins to close. And remove jumper clip from 2 jumper pins
to open. The following illustration shows how to set up jumper.
Before applying power to GOT5152T-832, please make sure all of the jumpers and
switch are in factory default position. Below you can find a summary table and
onboard default settings.
Jumper
Description
Setting
JP4
Auto Power On
Default: Disable
2-3 close
JP5
CF Voltage Selection
Default: +3.3V
1-2 close
JP6
Restore BIOS Optimal Defaults (Clear CMOS)
Default: Normal Operation
1-2 close
JP7
COM1 RS-232/422/485 Mode Setting
Default: RS-232
3-5, 4-6 close
JP8
3-5, 4-6 close
JP9
1-2 close
JP10
COM1 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP11
COM2 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close
JP12
COM3 Data/Power Selection
Default: RS-232 Data
Pin 1: DCD
3-5 close
Pin 9: RI
4-6 close

GOT5152T-832 User’s Manual
12 Hardware and Installation
Back
2.3.1 COM1 Configuration
The COM1~3 are a standard DB-9 connector. Those connectors are equipped with
The GOT5152T-832 has three serial ports. COM1 is RS-232/422/485, while COM2 and COM3 are
RS-232. The following table shows you set COM1 port mode:
Description
Jumper Setting
RS-232 (Default)
JP7
JP8
JP9
RS-422
JP8
JP7
JP9
RS-485
JP8
JP7
JP9
2.3.2 COM port Power Configuration
All of the serial ports can output data or power through jumper setting.
The following table shows you how to do that.
Description
JP10~JP12
Pin1: DCD
Pin9: RI
(Default)
Pin1: +5V
Pin9: +12V
Pin1: +5V
Pin9: RI
Pin1: DCD
Pin9: +12V
Note: Each port +5V Maximum: 2A, +12V Maximum: 1A.

GOT5152T-832 User’s Manual
Hardware and Installation 13
Back
2.3.3 Auto Power On (JP4)
If JP4 is enabled for power input, the system will be automatically power on
without pressing soft power button. If JP4 is disabled for power input, it is
necessary to manually press soft power button to power on the system.
2.3.4 Restore BIOS Optimal Defaults (JP6)
Put jumper clip to pin 2-3 for a few seconds then move it back to pin 1-2. Doing
this procedure can restore BIOS optimal defaults.
2.4 COM port Connector
The pin assignment of RS-232/RS-422/RS-485 is listed on the following table. If
you need COM1 port to support RS-422 or RS-485 mode, please refer to Jumper
Settings
Function
Setting
Enable auto power on
1-2 close
Disable auto power on (Default)
2-3 close
Function
Setting
Normal operation (Default)
1-2 close
Restore BIOS optimal defaults
2-3 close
Pin
RS-232
RS-422
RS-485
1
DCD
TX-
Data-
2
RXD
TX+
Data+
3
TXD
RX+
No use
4
DTR
RX-
No use
5
GND
GND
GND
6
DSR
No use
No use
7
RTS
No use
No use
8
CTS
No use
No use
9
RI
No use
No use

GOT5152T-832 User’s Manual
14 Hardware and Installation
Back
2.5 Ethernet
The GOT5152T-832 is equipped with a high performance Plug and Play Ethernet
interface, full compliant with IEEE 802.3 standard, and can be connected with a
RJ-45 LAN connector.
Please refer to detailed pin assignment list below:
Pin
100Base-T
1000Base-T
1
TX+
BI-DA+
2
TX-
BI-DA-
3
RX+
BI-DB+
4
NC
BI-DB-
5
NC
BI-DC+
6
RX-
BI-DC-
7
NC
BI-DD+
8
NC
BI-DD-
2.6 Mountings: Panel / Wall / Desktop / VESA
There are several mounting ways for the GOT5152T-832, Panel, Wall, Desktop and
VESA mountings.
2.6.1 Wall Mount
The GOT5152T-832 is designed for Wall mounting application. Please refer below
picture to equip the mounting kit.
Find out the screws as marked on the back side of chassis.
1
2
3
4
5
6
7
8
RJ-45