B-K lighting ArtiStar Remote ES16 Metal Halide User manual

THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
NEEDED
FOR
INSTALLATION:
By Others
RELEASED
1-26-16
REFERENCE NUMBER
INS132000
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
NEEDED
FOR
INSTALLATION:
By Others
3/16” and 5/64” Allen wrench
Wire connector
Drill bit and Drill
Mounting hardware
1/4”-28 Stainless Steel
Black Oxide Socket
Head Cap Screw
#8-32 Stainless
Steel set screw
Anchor Base
#8-32 Stainless
Steel set screw
Warning High Voltage Hot Surface
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
anunsafeconditionandvoidproductwarranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafeconditionandvoidproductwarranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING-ToreducetheriskofFIREORINJURYTOPERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turning on.
Donottouchhotlens,guard,orenclosure(seediagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.Oil
fromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingor
damagedshield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
REMOTE WIRING
Remote ballast installations require inter-connected wiring
between the lamp and ballast (By Others) and have specific
wiring requirements between these components. Ballast
manufacturers regularly recommend the following wiring
detailsforsuchinstallations.
Electronic Ballast
• 1FootMinimumand15FootMaximumRemote
WireLength(BallasttoLampSocket).
• Lampleadsmustberuninaseparate,dedicated
metalconduit.
• Lampleadsmustbe18gauge,wire type SF-2 or
SFF-2.
• Lamp leads must be placed in a minimum 1/2”
internal diameter conduit, pipe, or flexible
conduit.
• Theuseofmetalcladcableassembliesorservice
powercords(SJ,SO,etc.)isprohibited.
Magnetic Ballast
• 35Watt=15FootMinimumand50FootMaximum
RemoteWireLength(BallasttoLampSocket).
• >35 Watt = 1 Foot Minimum and 50 Foot
Maximum Remote Wire Length (Ballast to Lamp
Socket).
Please consult the factory through your local B-K Lighting
SalesRepresentativepriortofinalizinganyinstallationdetail
utilizingremoteballastwiring.
Failure to comply with specific wiring
requirements will void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
ArtiStar™ Remote
ES16 Metal Halide
Installation Instructions

8. Tighten the three (3) #8-32 stainless steel set
screws on anchor base and 1/4”-28 stainless
steel locking screw at the knuckle to secure all
aimingpositions.
6. Placefixtureontomountedanchorbaseand
press straight down until the two pieces are
flushwitheachother.
7. Use 3/16” Allen wrench to slightly loosen
¼”-28 stainless steel black oxide socket head
cap screw at the knuckle for vertical aiming
purposes.Rotatefixtureatbaseandaimfixture
todesiredhorizontallocation.
WIRING DIAGRAM
LINE (+)
FIXTURE
COM
WIRING DIAGRAM
REMOTE
POWER
SUPPLY
(-)
GROUND GROUND
RELEASED
1-26-16
REFERENCE NUMBER
INS132000
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
1. Study anchor base plan. Prepare mounting
surfaceforanchorbase.
2. Use 5/64” Allen wrench loosen three (3) #8-32
stainless steel set screws (do not remove set
screwsfromfixturebase).Removeanchorbase
frombottomoffixture.
4. Secureanchorbase tosolidsurface(i.e.wood,
concrete) using appropriate hardware for
specificsurface.
5. Make two connections from remote ballast
housing to fixture leads using proper wire
connectors (By Others). Connect incoming
groundwiretogroundwireprovidedinfixture
body.Seewiringdiagram.
3. Pull wires from remote ballast housing
necessary for installation (By Others). Feed
wiring through anchor base.
All line voltage connections must be
made in compliance with the National
Electrical Code. Failure to do so will void
warranty.
ArtiStar™ Remote
ES16 Metal Halide
Installation Instructions

RELEASED
1-26-16
REFERENCE NUMBER
INS132000.1
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
By Others
ArtiStar ™ Knuckle
Stability
Flange™
Power Pipe™
NEEDED
FOR
INSTALLATION:
By Others
3/16” and 5/64” Allen Wrench
WaterproofWireConnectors
Phillips Screwdriver
Warning High Voltage Hot Surface
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
anunsafeconditionandvoidproductwarranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafeconditionandvoidproductwarranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING-ToreducetheriskofFIREORINJURYTOPERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turning on.
Donottouchhotlens,guard,orenclosure(seediagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.Oil
fromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingor
damagedshield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
REMOTE WIRING
Remote ballast installations require inter-connected wiring
between the lamp and ballast (By Others) and have specific
wiring requirements between these components. Ballast
manufacturers regularly recommend the following wiring
detailsforsuchinstallations.
Electronic Ballast
• 1FootMinimumand15Foot Maximum Remote
WireLength(BallasttoLampSocket).
• Lampleadsmustberuninaseparate,dedicated
metalconduit.
• Lampleadsmustbe18gauge,wire type SF-2 or
SFF-2.
• Lamp leads must be placed in a minimum 1/2”
internal diameter conduit, pipe, or flexible
conduit.
• Theuseofmetalcladcableassembliesorservice
powercords(SJ,SO,etc.)isprohibited.
Magnetic Ballast
• 35Watt=15FootMinimumand50FootMaximum
RemoteWireLength(BallasttoLampSocket).
• >35 Watt = 1 Foot Minimum and 50 Foot
Maximum Remote Wire Length (Ballast to Lamp
Socket).
Please consult the factory through your local B-K Lighting
SalesRepresentativepriortofinalizinganyinstallationdetail
utilizingremoteballastwiring.
Failure to comply with specific wiring
requirements will void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
ArtiStar™ Remote
ES16 Metal Halide
Installation Instructions
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.

ARTISTAR™ RM ES16 METAL HALIDE
Power Pipe™Installation
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
4. Backfillwithpeagravelorsandpriortopour.
WIRING DIAGRAM
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade
Stability Flange Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
5. Pour concrete (By Others).
Label on Power Pipe™ indicates installation
depth with finished grade.
8. Tighten three (3) #8-32 stainless steel round
head Phillips screws at base and 1/4”-28
stainless steel black oxide socket head screw
attheknuckletosecureallaimingpositions.
RELEASED
1-26-16
REFERENCE NUMBER
INS132000.1
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade
Stability Flange Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
Finished grade
Pea gravel or sand
Concrete
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
2. Slide optional Stability Flange onto Power
Pipe™. Use optional Stability Flange to aid in
installationofPowerPipe™.
1. Excavate trench according to designed lighting
plan.Digholeaminimumof18”deepand10”wide
to accommodate Power Pipe™ at desired fixture
location(s).
Power Pipe Mounting Option
7. Insert wires and connectors into fixture base
and attach to Power Pipe™.    To aim fixture,
use 3/16” Allen wrench to slightly loosen ¼”-28
stainless steel black oxide socket head screw at
theknuckleforverticalaimingpurposes.Rotate
fixturetoaimtodesiredhorizontallocation.
6.  Make two connections from remote ballast
housing to fixture leads using proper wire
connectors (By Others). Connect incoming
ground wire to ground wire provided in
fixturebody.Seewiringdiagram.
3. Pull wires from remote ballast housing
necessaryforinstallation(ByOthers)through
Power Pipe™. Allow for additional cable to
makeconnectionstofixtureleadandfuture
service. Place Power Pipe™ in hole.
All line voltage connections must be made
in compliance with the National Electrical
Code. Failure to do so will void warranty.
LINE (+)
FIXTURE
COM
WIRING DIAGRAM
REMOTE
POWER
SUPPLY
(-)
GROUND GROUND
ArtiStar™ Remote
ES16 Metal Halide
Installation Instructions
DRIVER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.
DRIVER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY

PRELIMINARY
1-26-16
REFERENCE NUMBER
INS132000.2
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
TOOLS
NEEDED:
By Others
Universal Mounting Ring™
18 Gauge Wire
Warning High Voltage Hot Surface
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Followproductlabelinformationandinstructions.
• QualifiedPersonnel mustperform allservicing orrelamping of
this product.
• Beforewiringtopowersupplyandduringservicingorrelamping,
turnoffpoweratfuseorcircuitbreakerbeforeservice.
• The use of accessory equipment not recommended by the
manufacturerorinstalledcontrarytoinstructionsmaycausean
unsafecondition.Theuseofdamagedcomponentsmaycause
anunsafeconditionandvoidproductwarranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Donotblocklightemanatingfromproductinwholeorpart,
asthismaycauseanunsafecondition.
• Never operate the fixture with missing or damaged lens.
Lensmustbecleanedonregularbasis.
• Entire fixture may become extremely hot. Do not touch hot
lensorfixturebody.Donottouchthelampatanytime.Use
aclean,dry,softclothtohandlethelamp.Oilfromskinmay
damagethelampandcauseittorupture.
• Replace lamp only with correct wattage and type of lamp
markedonfixturelabel.
• All gaskets, o-rings and sealing surfaces must be kept clean
duringinstallationandservice;failuretodothismaycausean
unsafeconditionandvoidproductwarranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
LightedlampisHOT!
WARNING-ToreducetheriskofFIREORINJURYTOPERSONS:
Turnoff/unplugandallowtocoolbeforereplacinglamp.
LampgetsHOTquickly!Contactonlyswitch/plugwhen
turning on.
Donottouchhotlens,guard,orenclosure(seediagram/
picture).
Keeplampawayfrommaterialsthatmayburn.
Donotouchthelampatanytime.Useasoftcloth.Oil
fromskinmaydamagelamp.
Donotoperatetheluminairefittingwithamissingor
damagedshield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations · Additionally suitable for mounting within 4 ft. of the ground
IMPORTANT LISTINGS AND CERTIFICATIONS
3/16”, 1/8” and 5/64” Allen Wrench
WaterproofWireConnectors
Mounting Hardware
ArtiStar™ Knuckle
Canopy
REMOTE WIRING
Remote ballast installations require inter-connected wiring
between the lamp and ballast (By Others) and have specific
wiring requirements between these components. Ballast
manufacturers regularly recommend the following wiring
detailsforsuchinstallations.
Electronic Ballast
• 1FootMinimumand15Foot Maximum Remote
WireLength(BallasttoLampSocket).
• Lampleadsmustberuninaseparate,dedicated
metalconduit.
• Lampleadsmustbe18gauge,wire type SF-2 or
SFF-2.
• Lamp leads must be placed in a minimum 1/2”
internal diameter conduit, pipe, or flexible
conduit.
• Theuseofmetalcladcableassembliesorservice
powercords(SJ,SO,etc.)isprohibited.
Magnetic Ballast
• 35Watt=15FootMinimumand50FootMaximum
RemoteWireLength(BallasttoLampSocket).
• >35 Watt = 1 Foot Minimum and 50 Foot
Maximum Remote Wire Length (Ballast to Lamp
Socket).
Please consult the factory through your local B-K Lighting
SalesRepresentativepriortofinalizinganyinstallationdetail
utilizingremoteballastwiring.
Failure to comply with specific wiring
requirements will void product warranty.
ArtiStar™ Remote
ES16 Metal Halide
Installation Instructions

40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX [phone]
www.bklighting.com • [email protected]
B-K LIGHTING
WIRING DIAGRAM
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
PRELIMINARY
1-26-16
REFERENCE NUMBER
INS132000.2
3. Use 1/8” Allen wrench to mount fixture with
two (2) #10-24 hex screws to installed back
box. Do not over tighten.
Phase 2 - Finish Installation of Fixture.
1. Install universal mounting ring (supplied with
fixture)usingappropriatemountinghardware
(By Others). Align fixture mounting holes to
finalmountingposition.
2. Pull wires from remote ballast housing
necessary for installation (By Others). Make
two connections from remote ballast
housing to fixture leads using proper wire
connectors (By Others). Connect incoming
ground wire to ground wire provided in
fixturebody.Seewiringdiagram.
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
4. Use 3/16” Allen wrench to slightly loosen
¼”-28 stainless steel black oxide socket head
cap screw at the knuckle for vertical aiming
purposes. Use 5/64” Allen wrench to loosen
the three (3) #8-32 stainless steel set screws.
Rotate to aim fixture to desired horizontal
location.
5. Tighten the three (3) #8-32 stainless steel
set screws and 1/4”-28 stainless steel black
oxide socket head cap screw at the knuckle
tosecureallaimingpositions.
Phase 1 - Rough In
InstallationofBackbox
1. Install Conduit (By Others) to be used with this
product.
2. Installjunctionboxsothatfrontface
isflushwithfinishedwallorceiling.
3. Connect box to conduit and pull wires for
connections(SeeWiringDiagram).
Additional Info
• Please follow National and Local electrical codes for your
area.
• Suitableforthroughwire.
• Suitableforinstallationintocombustiblematerials.
• Ratedfor90°C.
LINE (+)
FIXTURE
COM
WIRING DIAGRAM
REMOTE
POWER
SUPPLY
(-)
GROUND GROUND
All line voltage connections must be
made in compliance with the National
Electrical Code. Failure to do so will
void warranty.
ArtiStar™ Remote
ES16 Metal Halide
Installation Instructions